what part is this and what glue works - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ABM Camaro · 12-01-2019, 04:41 PM

This is coming off on my car, and was glued on but its not holding.
What glue did you use to hold it on? Or whats the name of the part or part number to order a new one?

sbubbaklein · 12-01-2019, 08:58 PM

that is part of the quarter window and comes on it. 22829813 Left, 22829814 Right they cost about $210 each

ABM Camaro · 12-01-2019, 09:13 PM

I google those numbers and it comes up the glass window. I just need the rubber molding part number.

sbubbaklein · 12-01-2019, 09:39 PM

the rubber piece is attached to the window glass. It only comes as part of the glass already. attached to it.

ABM Camaro · 12-02-2019, 11:55 AM

well that's a fun sucker.

Anyone glue it and make it stick?

ABM Camaro · 12-04-2019, 07:07 AM

Anyone glue this with rubber molding back to the window with success?

sbubbaklein · 12-04-2019, 10:54 AM

why not try clear silicone seal. It will bond, waterproof, withstands temp changes. Get name brand such as 3m, loctite, gorilla.

ABM Camaro · 12-04-2019, 12:55 PM

I picked up Gorilla gel glue, JB weld ( which looks like its on the window ) and a tube of Flex Glue. Im not sure which Ill use yet. I do have a clear tube of silicon around.

sbubbaklein · 12-04-2019, 01:59 PM

on the locktite web site you chose the material to be bonded and they recommend clear silicone seal for rubber to glass.

ABM Camaro · 12-04-2019, 05:27 PM

Ill give it a shot. I removed the rubber, scrapped out the old glue, and tomorrow Ill reapply silicon

ABM Camaro · 12-08-2019, 04:24 PM

I used the Flex Glue and it seems to hold well for now. I did one window at a time so I could leave my clamps on it for 24 hours. If its doesnt hold, its not to hard to redo.

DaddySS · 12-29-2019, 05:57 AM

I would also look into why it's coming apart. The rubber shouldn't encounter anything that separates it from the glass and the pressure from the door window sealing against it should be slight. It seems either the door window or the quarter should be adjusted.

Sam9Fender · 01-21-2021, 12:29 PM

I solved a similar problem with hot glue from a nearby store. The glue holds perfectly for six months, while the result suits me as I do not see any cracks or something like that. I used the best glue gun model of 2020 because it was the only thing I had on hand at the time, and I needed to fix the problem quickly. Also, this glue gun did a great job when I was trying to fix one of the broken windshield wipers. I can vouch for its reliability as this glue has survived more than a dozen rains and damp air. I can't name the specific name of the glue since I bought the most standard glue gun glue from a hardware store.

mikeman · 02-02-2021, 03:04 PM

A urethane adhesive for windshields would probably work best for that application.

12-01-2019, 04:41 PM	#1
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	what part is this and what glue works This is coming off on my car, and was glued on but its not holding. What glue did you use to hold it on? Or whats the name of the part or part number to order a new one? Attached Images __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-01-2019, 08:58 PM	#2
sbubbaklein Drives: early 2011 Camaro convertible Join Date: Jul 2014 Location: House Springs, Mo Posts: 2,002 View My Garage	that is part of the quarter window and comes on it. 22829813 Left, 22829814 Right they cost about $210 each __________________ Early 2011 LT Convertible, ZL1 bumper, hood, side skirts, belly pan and wheels, Truecarbon ECF hood extractor, K&N CAI, Elite catch can, Big Worm Bow Tie emblems, Jacfab bracket, Vitesse TC, BMR strut brace, BMR tunnel brace, NPP exhaust

12-01-2019, 09:13 PM	#3
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	I google those numbers and it comes up the glass window. I just need the rubber molding part number. __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-01-2019, 09:39 PM	#4
sbubbaklein Drives: early 2011 Camaro convertible Join Date: Jul 2014 Location: House Springs, Mo Posts: 2,002 View My Garage	the rubber piece is attached to the window glass. It only comes as part of the glass already. attached to it. __________________ Early 2011 LT Convertible, ZL1 bumper, hood, side skirts, belly pan and wheels, Truecarbon ECF hood extractor, K&N CAI, Elite catch can, Big Worm Bow Tie emblems, Jacfab bracket, Vitesse TC, BMR strut brace, BMR tunnel brace, NPP exhaust

12-02-2019, 11:55 AM	#5
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	well that's a fun sucker. Anyone glue it and make it stick? __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-04-2019, 07:07 AM	#6
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	Anyone glue this with rubber molding back to the window with success? __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-04-2019, 10:54 AM	#7
sbubbaklein Drives: early 2011 Camaro convertible Join Date: Jul 2014 Location: House Springs, Mo Posts: 2,002 View My Garage	why not try clear silicone seal. It will bond, waterproof, withstands temp changes. Get name brand such as 3m, loctite, gorilla. __________________ Early 2011 LT Convertible, ZL1 bumper, hood, side skirts, belly pan and wheels, Truecarbon ECF hood extractor, K&N CAI, Elite catch can, Big Worm Bow Tie emblems, Jacfab bracket, Vitesse TC, BMR strut brace, BMR tunnel brace, NPP exhaust

12-04-2019, 12:55 PM	#8
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	I picked up Gorilla gel glue, JB weld ( which looks like its on the window ) and a tube of Flex Glue. Im not sure which Ill use yet. I do have a clear tube of silicon around. __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-04-2019, 01:59 PM	#9
sbubbaklein Drives: early 2011 Camaro convertible Join Date: Jul 2014 Location: House Springs, Mo Posts: 2,002 View My Garage	on the locktite web site you chose the material to be bonded and they recommend clear silicone seal for rubber to glass. __________________ Early 2011 LT Convertible, ZL1 bumper, hood, side skirts, belly pan and wheels, Truecarbon ECF hood extractor, K&N CAI, Elite catch can, Big Worm Bow Tie emblems, Jacfab bracket, Vitesse TC, BMR strut brace, BMR tunnel brace, NPP exhaust

12-04-2019, 05:27 PM	#10
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	Ill give it a shot. I removed the rubber, scrapped out the old glue, and tomorrow Ill reapply silicon __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-08-2019, 04:24 PM	#11
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	I used the Flex Glue and it seems to hold well for now. I did one window at a time so I could leave my clamps on it for 24 hours. If its doesnt hold, its not to hard to redo. __________________ 2013 ZL1 Camaro A6. ARH Headers, K&N intake, Tuned by Tampa Tuning 2014 V6 Camaro bolt ons and E85 Tuned by Tampa Tuning

12-29-2019, 05:57 AM	#12
DaddySS Kept The Faith Drives: 2011 Camaro SS Convertible Join Date: Jan 2007 Location: Bergen County, New Jersey Posts: 418	I would also look into why it's coming apart. The rubber shouldn't encounter anything that separates it from the glass and the pressure from the door window sealing against it should be slight. It seems either the door window or the quarter should be adjusted. __________________ 2011 Vert - 2SS/RS 6spd Triple Black

01-21-2021, 12:29 PM	#13
Sam9Fender Drives: chevrolet camaro Join Date: Jan 2021 Location: USA Posts: 1	I solved a similar problem with hot glue from a nearby store. The glue holds perfectly for six months, while the result suits me as I do not see any cracks or something like that. I used the best glue gun model of 2020 because it was the only thing I had on hand at the time, and I needed to fix the problem quickly. Also, this glue gun did a great job when I was trying to fix one of the broken windshield wipers. I can vouch for its reliability as this glue has survived more than a dozen rains and damp air. I can't name the specific name of the glue since I bought the most standard glue gun glue from a hardware store. Last edited by Sam9Fender; 01-26-2021 at 12:07 PM.

02-02-2021, 03:04 PM	#14
mikeman Banned Drives: 2015 Camaro Join Date: Aug 2018 Location: My Garage Posts: 1,125	A urethane adhesive for windshields would probably work best for that application.