12-26-2012, 01:37 PM | #29 |
Drives: 2018 Camaro ZL1 Join Date: Feb 2011
Location: Midwest
Posts: 257
|
pm pricing to 53089 please!!
|
12-26-2012, 06:28 PM | #30 |
|
Please PM pricing to business zip 37932, if it makes a difference I'm with an AC Delco auto repair shop.
Ed M.
__________________
RJT 2SS/RS, AAM 3.70's, MTI Sway Bars, Shifter & SS brake lines, ZLI calipers, rotors & pads, BMR Trailing & Toe Arms, rear cradle & diff bushes, Pedders XA's, Camber/Toe eccentrics, Radius arm inserts, GTO clutch reservoir, LS9 cam, Comp valve springs, Melling 10296 oil pump, CR5 timing chain, LS6 damper, CAI Cold Air Intake, ARH LT headers w/HF cats, GMPP touring axle back, Elite Engineering Catch Can, Forgeline 20x9.5 & 20x11 DS3 whls, 275/40/20 & 315/35/20 tires, 2011 Convertible spoiler, 1LE front spoiler, Lloyd "SS" Floor Mats, GM Camaro Trunk Mat, wrapped console & Grant steering wheel.
|
12-26-2012, 08:12 PM | #31 |
Emerald Coast Camaros
Drives: 2010 RS/SS Rally Yellow & 68 SS Join Date: Dec 2012
Location: Woodville,FL.
Posts: 1,814
|
Your car has a cross member but kit does not why not? I just run the 1/4 mile are you saying all i would need is the rear with out cross member. And will it work for a all stock suspension with out other up grades?
|
12-26-2012, 08:30 PM | #32 |
Emerald Coast Camaros
Drives: 2010 RS/SS Rally Yellow & 68 SS Join Date: Dec 2012
Location: Woodville,FL.
Posts: 1,814
|
On the front two bolts with out full kit would it bolt to the sub frame???
|
12-27-2012, 04:21 PM | #33 |
Drives: 2018 white redline edition Join Date: May 2011
Location: PA
Posts: 52
|
Can you pm me a price? Thank you
|
12-27-2012, 11:40 PM | #34 |
pm price please
|
|
12-27-2012, 11:54 PM | #35 |
Drives: Florida Speed & Power Join Date: Jan 2011
Location: Pinellas Park, FL
Posts: 3,185
|
Pm price pls
|
12-28-2012, 12:05 AM | #36 |
instigator
Drives: 2020 6.2 Trail Boss, 2022 XC90 Join Date: Jan 2010
Location: 72034
Posts: 3,979
|
the install instructions are on their website. One tip I can pass on...put the 2 outer center bolts in with the inserts and the carrier bearing brace bolts x4 in first. Bring the rear cradle four bolts and forward 2 most bolts all down evenly. Just work your way around back and forth. The brace pre-loads and this is the easiest way I found. Two guys with air impacts knock it out in 5 min. lol
__________________
-John S.
|
12-28-2012, 09:33 AM | #37 | |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
Quote:
It does not interfere with any of the control arms, or mounting locations so any subframe bushing kit, or aftermarket control arms would be fine to use, as would all stock pieces. |
|
12-28-2012, 09:38 AM | #38 |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
Pricing sent!
|
12-30-2012, 08:31 AM | #39 |
pm pricing please
__________________
TSP 1 7/8, CNT catback, VMAX, CAI intake, ADM scoop, 3.70s, Adm Tuned(374/391), SLP UDP, 18" nurbs/NT05r's , 3200 stall, Granatelli trailing arms....1/4 mi best 12.7
|
|
12-31-2012, 09:15 AM | #40 |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
|
12-31-2012, 09:51 AM | #41 |
Drives: 2010 CAMARO RALLY YELLOW SS/RS/M6 Join Date: Aug 2012
Location: Aransas Pass Texas
Posts: 565
|
PM Price please!
__________________
I LIKE TO GO FAST!
Lethal Racing Night Fury Cam Kit, Melling oil pump, C5R Timing Chain, Dyno Tuned by Shawn@Lethal Racing, Vararam Tuned intake, Vararam Power Wedge, LSR Tri Ax Short throw Shifter, VMAX Ported T/B, TSP 2" L/T Headers, TSP Cat delete, Borla axle back exhaust, Innovate A/F monitor, 471.7 HP/438.8 TQ |
12-31-2012, 10:08 AM | #42 |
Account Suspended
Drives: 2011 2SS RS 6M Inferno Orange Join Date: Nov 2010
Location: San Clemente CA
Posts: 309
|
Pm price please
|
|
|
|
|