08-27-2011, 03:48 PM | #1 |
Quit being a pu$$y
|
Sealed up intake scoop, increased flow & relocate washer bottle.
Another big shout out to Apex Motorsports for their AWESOME products and THE BEST price! I had pretty much decided that I wasn't going to buy any more parts for my car because I was happy where it was and have a cam & springs sitting on the shelf waiting to be installed, but this thread got me thinking. http://www.camaro5.com/forums/showthread.php?t=166416
I has seen the scoop before, but didn't think it was worth $100 and i didn't want to loose windshield washer capabilities. Then steps in Apex with their affordable bundle of the scoop and a smaller, lighter for under $135 shipped! I didn't think much of the scoop from the pics online but once installed I really liked it. It really forms a good ram air pathway from the lower front grill. I had previously sealed up my Volant cold air intake and so I sealed all the gaps to make the scoop more efficient. I used aluminum A/C ducting tape and good old regular duct tape. I know what you are thinking, "That isn't going to hold up well.". I know that, I first sealed up my intake about 4 months ago and most of the tape has help up great. I figure I'm going to pull my fender well every few months to get to my filter to clean it and re oil it, so I'll just fix any tape that comes up. The tape not only helps keep all the air going straight to the filter, but more importantly it helps keep all the hot under hood air out. I also increased the airflow by at least 10% by removing the little triangular tab that sticks into the scoops air pathway. I measured the scoop pathway at 19.25 sq inches and the little triangular tab at 2 sq inches. I actually had to remove the scoop to be able to cut the tab a little higher and completely remove it. The washer bottle relocate was very high quality and wash VERY easy to install. AutoAgenda said that you might only get 3 uses out of this washer bottle before it runs out, but unless you use 5-6 cups of washer fluid per use that is NOT going to happen. In fact I marked where my stock washer bottle level was when I pulled it out (I have never used it so it was still full and I didn't spill any while swapping it out) and the Apex bottle hols more than half of what was in the stock washer bottle holds. The bottles fill cap also fits PERFECTLY in my Volant washer hole. I only secured it with a crap ton of duct tape for now until I fab up more sturdy way to hold it in place (to be honest I will probably leave it like this to see how long it holds up). Cost of today's mods: $134.99
__________________
|
02-03-2012, 05:51 AM | #2 | |
Drives: 2000 Camaro SS Join Date: Feb 2010
Location: Louisville, Ky.
Posts: 25,179
|
Outstanding post, I can't believe I had not seen it until now. Thank you for the great review.
Quote:
That is awesome how seamlessly it mated up with your Volant. It looks like it was meant to be there from the beginning. Last edited by Apex Motorsports; 02-03-2012 at 06:10 AM. |
|
09-05-2014, 09:20 PM | #3 |
Drives: 2010 CGM Chevrolet Camaro LS Join Date: Feb 2014
Location: St. Louis, MO
Posts: 510
|
I have a Volant CAI. Looks like I need to add some more airflow into my CAI and this mod will do the trick!
__________________
2010 Chevrolet Camaro CGM LS - Performance Mods: "Everything I can get bolt-on wise to make it run good!"
Exterior Mods: "Everything I can get to make it look good!" Interior Mods: "Everything I can get to make it look good!" |
09-06-2014, 12:18 PM | #4 |
Drives: 73 VETTE ,, 05 2500hd diesel,14 1LE Join Date: Feb 2014
Location: The Left lane PHOENIX AZ
Posts: 2,626
|
And the best part is it works great .
__________________
OLD GUY FLYING FAST AND LOW
|
09-08-2014, 05:10 AM | #5 |
Drives: 2000 Camaro SS Join Date: Feb 2010
Location: Louisville, Ky.
Posts: 25,179
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cold Air Inductions Intake System! ADM Performance Cold Air Scoop! & Packages! | AutoAgenda | V8 Bolt-Ons & Tunes | 438 | 11-23-2013 10:49 PM |
question about CAI & Relocation of the washer Bottle | luis nunez | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 1 | 07-28-2011 10:48 PM |
ADM Performance "Street" and "Race" intake systems from Apex Motorsports | Apex Motorsports | V8 Bolt-Ons & Tunes | 12 | 07-16-2010 07:47 PM |
Great Read and Info on Oil Weight | Banshee | Mechanical Maintenance: Break-in / Oil & Fluids / Servicing | 1 | 11-23-2009 09:03 PM |
My New ADM Painted RJT High Flow Intake is on w/ Pics! | GMRULZ | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 21 | 10-26-2009 04:54 PM |