12-18-2011, 05:44 AM | #1 |
My First Chevy
Drives: 2011 Camaro 1LT/RS M6 Join Date: Jan 2011
Location: Whittier, CA
Posts: 47
|
Removing/installing throttle body?
I'll be installing my catch can tomorrow and want to clean off the throttle body. How do I remove and reinstall the throttle body? I hear it's only 4 bolts, so is it really that simple? I'm not that great of a mechanic so I don't want to mess anything up LOL.
|
12-18-2011, 06:01 AM | #2 | |
having FUN now 13.66@101
|
Quote:
Yes it is that easy. 4 bolts. The key is to NOT over tighten the bolts on the re-install. It is only like 89 inch lbs. Not ft. lbs.
__________________
|
|
12-18-2011, 09:39 AM | #3 |
Account Suspended
Drives: 2012 Camaro RS, RX supercharged Join Date: Dec 2009
Location: Bradenton, FL
Posts: 6,063
|
Look inside the intake manifold snout at the oil caught in the depression just inside the bottom of the snout. That needs to be soaked out with paper towel.
|
12-18-2011, 10:57 AM | #4 |
Drives: Really Slow Join Date: Apr 2010
Location: PA
Posts: 56,957
|
There is also a connector that needs to be unplugged.
__________________
|
12-18-2011, 08:55 PM | #5 |
|
Make sure to push this vvv
Sent from my iPhone using Tapatalk
__________________
IPF supercharger kit, IPF tune, SW LT's, R. Tech HFC's, ARK DT-S catback, SS Brembo brake upgrade, BC Racing adjustable coilovers, Hurst STS, Pfadt rear arm package, Pfadt adjustable sways & end links, Pfadt diff bushings, BMR rear cradle full kit blk bezels,SS diffuser, Innovate gauges.
|
12-19-2011, 09:38 AM | #6 |
Account Suspended
Drives: 2012 Camaro RS, RX supercharged Join Date: Dec 2009
Location: Bradenton, FL
Posts: 6,063
|
LOL SixJak!!! My wife HAS one of these!!!!
|
12-19-2011, 09:52 AM | #7 |
The Mark of Excellence
Drives: 2010 ABM 1SS RS LS3 Join Date: Jan 2009
Location: Smallest State in the Union
Posts: 8,690
|
It has an O-ring, not a gasket, the TB will fall off when the bolts come out, so hang on to it and the O-ring. I think the retorque is 89 in lbs.
__________________
BMR, CAI, DynoMax, Elite Eng., Hurst, Jannetty, Clear Image Headers & Hi Flow cats, Jet Hot, LSR, TSW, VMax, Vredestein Last edited by PAUL SS; 12-19-2011 at 10:03 AM. |
12-19-2011, 10:43 AM | #8 | |
having FUN now 13.66@101
|
Quote:
The V6 is not an O ring, but a steel gasket. True I recommend hanging onto the TB when removing the bolts. And yes, I did post that it is 89 INCH lbs. Be careful when applying the pressure back on those bolts.
__________________
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cold Air intake, throttle body, headers, lots of questions. | shadowghost21 | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 6 | 10-09-2011 03:59 PM |
95mm Wilson Throttle Body | Jim85IROC | V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment | 0 | 12-29-2009 09:17 AM |
Best method to clean a throttle body on '99 Z | Broshot | 4th Generation Camaros | 5 | 07-19-2009 11:50 PM |