04-13-2013, 04:35 PM | #1 |
|
with a +44 rear offset. how far out will the tire come out the rear fender
With..... 20X11 5X120, offset +44 rears, 2.5" lip. How far will the tire come out to the rear fenders with a 315/35/20 or 305/40/20 ? with verdstien ultra sassanta tires or nitto invo's thanks if anybody knows
|
04-14-2013, 10:01 AM | #2 |
|
I have 20x11 Forgestars (+42 offset), with Continental Extreme Contact DWS Tires (315/35R20). If I was to hold a straight edge up against the tire, I would say they probably stick out about a 1/4" beyond the fender lip. But these tires have a pretty good curb protection lip on them, they do stick out past the wheel more than other tires I've seen....which is fine with me, I don't like curb rash!!! I would think the wheel/tire combination you are talking about should be flush, or maybe stick out slightly less than mine.
Last edited by blazzin1; 04-15-2013 at 01:42 PM. |
04-14-2013, 11:20 AM | #3 |
Drives: 2SS/RS CGM LS3 Join Date: Aug 2009
Location: NJ
Posts: 1,619
|
I currently have 20x11 +45 with (315/35) NT05 and they are just within the fender when viewed straight down. IMO a +44 with with invos should be fine, I have read that they are a touch smaller than the NT05? Depending on brand a 305/35 would should obviously be smaller.
|
04-14-2013, 02:57 PM | #4 | |
|
Quote:
|
|
04-14-2013, 03:00 PM | #5 | |
|
Quote:
|
|
04-14-2013, 05:52 PM | #6 |
|
|
04-14-2013, 06:24 PM | #7 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
35 off sets fit with 315 Invos at edge (agressive ) 42 no problem .
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
04-14-2013, 09:24 PM | #8 | |
|
Quote:
|
|
04-14-2013, 09:26 PM | #9 |
|
|
04-16-2013, 04:09 PM | #10 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
Need better ones.
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
04-24-2013, 01:41 PM | #11 |
|
nice skar, looks like they come a little past the fender looks nice however. its tuff, I might go with 305 rear, but might be to far inboard with my +44.
|
04-24-2013, 02:46 PM | #12 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
[/ATTACH]Flush even with edge using broom stick touching bottom and top of tire and fender .All depends on angle that you look at.
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
|
|
|
|