10-18-2022, 04:47 PM | #239 |
PaPa Smurf
|
I used a modeling knife to get behind it and work it off slowly. It will bend if you just go at prying on it. Then used 3M 50lb "tape" to attach it to the core support under the Chevrolet "plaque". It's not very difficult at all to remove the cover and work on it at a table. Also moved it as I changed to the LT2 IM and LT5 TB.
__________________
2022 Rapid Blue SS 1LE
|
12-09-2022, 06:58 AM | #240 |
Drives: 2020 SS Join Date: Nov 2022
Location: San Marcos CA
Posts: 35
|
After lurking for a little, this topic caught my attention and I had to check my recently purchased 2020 SS M6. Low and behold, another Latrice Carothers built engine.
Thanks Latrice, it runs strong! |
12-09-2022, 10:19 AM | #241 |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,726
|
She is very prolific with you guys' engine builds, that's for sure
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
05-09-2023, 11:28 AM | #242 |
Drives: Chevrolet Camaro Join Date: Apr 2023
Location: St Louis
Posts: 14
|
Here's mine, 2023 ZL1 A10, purchased last week off the dealer showroom floor.
|
09-23-2023, 11:18 PM | #243 |
Drives: Chevrolet Camaro 2SS 1LE Join Date: Apr 2023
Location: TX
Posts: 12
|
Just looked today and found this. 23 2SS 1LE M6 bought off the showroom floor in April
|
09-24-2023, 08:16 AM | #244 |
Drives: 19 ZR1 20 350R Wife -> 24 ZL1 Vert Join Date: Nov 2016
Location: Graham, Texas
Posts: 246
|
Congrats
|
02-10-2024, 10:31 PM | #245 |
Drives: Chrysler Pacifica Join Date: Aug 2022
Location: Michiga
Posts: 4
|
I considered relocating it but ended up finding a place that could make a replica. (slightly larger than the 'real' one by my request)
2023 M6 2SS Convertible |
02-10-2024, 11:06 PM | #246 |
Drives: 1987 IROC, 2020 ZL1 Join Date: Nov 2023
Location: Nashvile
Posts: 74
|
|
02-10-2024, 11:14 PM | #247 | |
Drives: 2020 Chevrolet Camaro Coupe 2SS 1LE Join Date: Feb 2020
Location: Nevada
Posts: 300
|
Quote:
Your Vette intake looks good. Can you remove those studs for the old intake cover? That would clean up your engine bay even more. |
|
02-12-2024, 10:23 PM | #248 | |
Drives: Chrysler Pacifica Join Date: Aug 2022
Location: Michiga
Posts: 4
|
Quote:
I contacted https://anchor-room.com/ and showed them a picture of what I wanted. They worked up an example and sent it to me for approval over email. I also had them make that plate I put on the strut tower brace. |
|
02-13-2024, 03:05 PM | #249 |
Drives: '23 2SS RSblue 6MT, sold '19 ND2 Join Date: Dec 2021
Location: Los Angeles
Posts: 269
|
Found it!
Popped it off with plastic trim tool. Moved to the proper spot with some new double sided duct tape. 2023 2SS 6 speed
__________________
'23 2SS, 6 speed, NPP, Copper-free brakes, 56V Carbon Flash Rims, Riverside Blue
1LE sway bars EOS front splitter 5-6-22:1100, 7-19-22: 3000, 8-3-22: TPW 8/15/22, 10-4-22: ETA 10/13/2022 10-15-22 6000 |
02-13-2024, 06:18 PM | #250 |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,726
|
Looks a bit strange to me... the plaque was attached to the engine in the first place because the builder assembled the engine, not the entire car...
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
02-13-2024, 11:37 PM | #251 |
Drives: '23 2SS RSblue 6MT, sold '19 ND2 Join Date: Dec 2021
Location: Los Angeles
Posts: 269
|
I thought that's where they are placed for the other lt4's made in bowling green. Now I see there's a spot for it. If I have to swap the engine I guess I'll have to remove it.
__________________
'23 2SS, 6 speed, NPP, Copper-free brakes, 56V Carbon Flash Rims, Riverside Blue
1LE sway bars EOS front splitter 5-6-22:1100, 7-19-22: 3000, 8-3-22: TPW 8/15/22, 10-4-22: ETA 10/13/2022 10-15-22 6000 |
02-14-2024, 12:28 AM | #252 | |
Drives: 1987 IROC, 2020 ZL1 Join Date: Nov 2023
Location: Nashvile
Posts: 74
|
Quote:
Thank you for sharing! |
|
|
|
Post Reply
|
|
|