12-08-2013, 04:03 PM | #155 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
Today I installed some oracle ghost side markers that I picked up at a h-town Camaro club gathering last night.
__________________
|
12-24-2013, 09:54 AM | #156 |
Drives: 2013 Black Camaro 2SS/RS Convert. Join Date: Jun 2013
Location: Sauk Village, Illinois
Posts: 506
|
Nice build man
__________________
2013 Camaro 2SS/RS-Smoked tail lights and side markers, HID log lights, & LED lighting inside/outside the car, SJM LED Cupholder, SJM full dashboard ABL lighting, ZL1 Rockers, 1LE Splitter, Showstopper LED Mirrors, Showstopper LED Side Markers, & Showstopper Heat Extractor Hood, 20" Niche Concourse ZL1 Styled wheels 20X8.5 & 20X10 with 275/40/20 & 315/35/20 Nitto Invos, Black Gorilla Lug Nuts/Locks, Black Billet Elite Camaro License Plate Holder, and Hydro Dipped Speedo/Shifter/AC-Heat Bezels.
|
12-27-2013, 08:35 AM | #157 |
Drives: 05 GTO / JETTA TDI Join Date: Jan 2012
Location: St Pete Fl
Posts: 630
|
Did you ever get a Chiller that works?
|
12-27-2013, 12:53 PM | #158 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
Thanks. So Tracy at RX sent me a bigger chiller (30 plate vs 20 plate). I have not had time to change it out yet. I'm still little worries about the competition switch. Haven't had any luck with it. Going to try and fix it when I change out the chiller. I hope to do it next week. I'll post up results. I definitely appreciate Tracy working with me on this. He gets a bad wrap, but I think he means well. Just hard for these performance shops to go from local to national overnight.
__________________
|
12-31-2013, 06:18 PM | #159 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
Road race at NOLA Motorsports park
I went road racing again Sunday. I'm really liking this. I have my StopTech rotors and cobalt friction brake pads on the way. Unfortunately I may have needed them Sunday...I ran off the track going into turn a little hot... There was minor damage...you can see in the video the back panel peeled off a bit. However, as I was trying to clean off the mud and grass from underneath...I wasn't paying attention and jack slid off and punctured my radiator... What a dumb ass...
Video of my fasted lap and when I slid off track (from rear and front): http://youtu.be/eDSs2GJabEQ I installed my custom RPM transmission last week...it worked fine, but I still can't shift to 5th over 6K rpm...wth? I'll be working on my new nitrous kit, brake upgrades, and bigger chiller between now and my next drag race event on Jan 26th at Royal Purple raceway (Home of Camaro Fest 2014 ).
__________________
|
01-01-2014, 10:50 AM | #160 |
Drives: 05 GTO / JETTA TDI Join Date: Jan 2012
Location: St Pete Fl
Posts: 630
|
All the RX kits I removed had the wrong switch, he is still using my idea but an On/Off switch so if yours is wired the same you need to get an ON/ON switch. This gives the Freon solenoid ground in one position and the LED ground in the other. I could send you an old diagram or you could go to my new setup that has 2 relays primarily for ¼ mile. Let me know if I can hook you up, one of my wiring harnesses would not fit, things are in a different location but the diagram still applies.
|
01-01-2014, 05:42 PM | #161 | |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
Quote:
Thanks!
__________________
|
|
01-02-2014, 05:01 AM | #162 |
SoCal HT5
Drives: The Punisher Join Date: Oct 2012
Location: Lebanon
Posts: 646
|
Happy New Year!!
Best wishes... |
01-04-2014, 04:22 PM | #163 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
thanks, Happy New Year to you too!
__________________
|
01-05-2014, 12:37 PM | #164 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
PMJ's 2SS/RS Whipped 416 M6 aka BlackWidow [COTW 6/10/13]
So I didn't get to install my Nitrous and brake upgrades over the holidays like I hoped, but I did get my RPM transmission installed and repaired my radiator from stupid incident at NOLA Motorsports park last Sunday.
Anyway, I made it out to RPR (hope of the next C5 Fest) Friday night and set a new personal best 10.72 @ 137. It was ridiculously busy...I was there 7 hours never got out of line and got 3 runs in. Here are some videos: My first 2 runs...lots of angles: http://youtu.be/MxYy2s7IUfE Just my 10.72 run... http://youtu.be/k8T2E-Mij2U Here is the video of my 3rd run. I paired up with Jaime in BeaSSt...he took the hole shot, but he missed 3rd gear. It would have been a great finish. I ran a 10.8. http://youtu.be/Y3jTB8ZgvKI
__________________
Last edited by PMJ; 01-05-2014 at 04:15 PM. |
01-29-2014, 11:26 PM | #165 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
I raced last Sunday at Royal Purple again at the Texas Speed Syndicates Fast 30 event... I just got my nitrous system installed and was excited.
Turns out I brought a broken car...my whipple belt tensioner pin broke and I wasn't getting any boost. Made a new pin from a bolt. Drilled hole there the original pin was and was back in business. Nitrous increased my trap 7 mph...to 144. And lowered my et .3. But I think there's more to be gained. http://youtu.be/NM4WKl2PWSc
__________________
|
01-30-2014, 07:26 AM | #166 |
Drives: 2013 Camaro ZL1 bone stock 9K miles Join Date: Oct 2010
Location: Philadelphia, PA
Posts: 389
|
Looking good!
I see your getting your 60 foot times to 1.5's! that's not bad at all! What gear are you running for the 1/4 mile, the 4.11's still? I was thinking if I ran a 1.5 60 foot I'd be at 12.2's! Man I can't wait to I really dig in mine! Track opens in a couple months. Can't wait to try my new twin disc clutch! Have fun be safe. George.
__________________
SLP- long tube headers, hi flow cats w/full SLP 3'' PowerFlo exhaust incl/X-pipe, 160 degree stat, SLP Blackwing CAI. Dyno tuned by ECS-407/409RWHP&TQ. BMR- trailing arms w/poly knuckle bushings, toe links, cradle bushings and differential bushings. QA1 rear lower control arms. Hurst short throw shifter, SS- level 4 axles, DSS- aluminum driveshaft, Pfadt- sport 1.5" rear sway-bar. SPOHN 1.25" front sway-bar. Monster LT1-S twin clutch. Prothane motor mounts. Best 1/4 mile so far- 12:70ET @ 112.24 MPH w/ 2.06 second 60'.
SOLD. |
01-30-2014, 07:54 AM | #167 | |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
Quote:
It was at an event last April that i was talking to a guy (friend now) describing his launch technique...i've been trying to master ever since. Definitely helped. He runs 9s in a manual (Corevette)! The first time i tried it that night, i broke a stock axel . Ironic thing is i had my ZL1 driveline at home...just didn't have time to install yet. THe ZL1 seems to hold up (and my RXT clutch). THe technique is simply on the launch to slowly release the clutch as you slowly move to open throttle. Feathers the clutch and keeps the engine power up. My biggest problem is a mental block concerned with spinning the tires....i very rarely get to WOT in 1st gear. That's something i'm going to concentrate on my next trip to the track!
__________________
|
|
01-30-2014, 01:10 PM | #168 | ||||
Drives: 2013 Camaro ZL1 bone stock 9K miles Join Date: Oct 2010
Location: Philadelphia, PA
Posts: 389
|
Quote:
I'm thinking of putting the 3.91's in my stock diff untill I can get the HammerHead, I already got the axles installed, just have to change the stubs that go into the diff to use my axles. I was going to go with the ZL1 diff, but I wanted to piece it together. I broke a axle at the line too, I even got a video (in car) of it I will post when I get home from work. I love the twin disc Monster clutch, I'm hoping I can slip it a little better then the single. I leave the line at only 2500 RPM, due to stock tires & gears, my average is about a 2.3 without killing it, wheel hop is violent if any better, with the stock low profile tires! I'm used to an auto at the track so this is a learning experience with me too, but you got a whole lot more POWER then me, I'll get there soon enough! Here's the video link when I broke an axle- Here's one spinning 1st- Here's one of my stock decent runs-
__________________
SLP- long tube headers, hi flow cats w/full SLP 3'' PowerFlo exhaust incl/X-pipe, 160 degree stat, SLP Blackwing CAI. Dyno tuned by ECS-407/409RWHP&TQ. BMR- trailing arms w/poly knuckle bushings, toe links, cradle bushings and differential bushings. QA1 rear lower control arms. Hurst short throw shifter, SS- level 4 axles, DSS- aluminum driveshaft, Pfadt- sport 1.5" rear sway-bar. SPOHN 1.25" front sway-bar. Monster LT1-S twin clutch. Prothane motor mounts. Best 1/4 mile so far- 12:70ET @ 112.24 MPH w/ 2.06 second 60'.
SOLD. Last edited by 10 2SS/RS 6M; 01-30-2014 at 07:19 PM. Reason: Added video's |
||||
|
|
|
|