2017 ZL1 Eibach Pro Kit Springs installed

AZ Charlie · 07-22-2017, 04:09 PM

I had a great experience once again with Eibach and Rich, Mike and the team at DynoComp in Scottsdale, Arizona that performed all the work. I talked to them by phone to make sure I received the correct springs that would not affect my existing stock suspension but would lower the car to a satisfactory height. I am extremely pleased.

Part number: E10-23-018-01-22

Some things I did while we had the wheels off:
1. Removed the large disc covers up front and installed the smaller covers. Since I live in Arizona and not my daily driver their is no need for me to have the larger disc covers. I installed the smaller disc covers that is recommended for track use so the rotors will get proper cooling.
2. I installed the ZL1 Add Ons rock guards on all four corners. This will be discussed in another thread and a complete build thread I will start on my car for forum friends to follow.
3. Since we should do a wheel alingment after replacing springs I went ahead and did the ZL1 Chevrolet specs for camber, caster and toe for track setup.

Here are the specs: https://my.chevrolet.com/content/dam...tion-guide.pdf

Per Eibach I should see a one inch drop in front and half inch drop in back. When we did the conversion at DynoComp in Scottsdale, AZ we were surprised how much better the car looked and it did look like it dropped the car significantly more than what Eibach stated but as you can see by the images Eibach was on point.

USP45 · 07-22-2017, 04:39 PM

Exactly what I have been looking at doing... have you noticed much difference in ride/handling? Might be too soon to answer that since you just had them installed...

Bow Tie Affair · 07-22-2017, 04:42 PM

What is the Eibach part number on the box?

Infern0 · 07-22-2017, 05:29 PM

Love it. Accent pieces look great too.

Stephen12ZL1 · 07-22-2017, 07:33 PM

Very nice!

AZ Charlie · 07-22-2017, 07:57 PM

Quote:

Originally Posted by USP45

Exactly what I have been looking at doing... have you noticed much difference in ride/handling? Might be too soon to answer that since you just had them installed...

I have only driven it about 30 miles since completed and honestly can not tell the difference but I always drive it in track mode for the exhaust note until my cat back comes in. At least in track mode no difference.

AZ Charlie · 07-22-2017, 07:58 PM

Quote:

Originally Posted by Bow Tie Affair

What is the Eibach part number on the box?

Part number from my receipt is in initial thread. I can verify next week when I get to my office if it is the same part number which I am sure it will be.

AZ Charlie · 07-22-2017, 08:00 PM

Quote:

Originally Posted by Stephen12ZL1

Very nice!

Thanks Infern0 and Stephen! Look forward to seeing what your new ZL1 will time at VIR! When are you going to track it there?

Bow Tie Affair · 07-22-2017, 08:28 PM

Quote:

Originally Posted by AZ Charlie

Part number from my receipt is in initial thread. I can verify next week when I get to my office if it is the same part number which I am sure it will be.

Thank You Sir!

Good job on the mods!

Stephen12ZL1 · 07-22-2017, 09:20 PM

Quote:

Originally Posted by AZ Charlie

Thanks Infern0 and Stephen! Look forward to seeing what your new ZL1 will time at VIR! When are you going to track it there?

VIR certainly in November but possibly sooner if my calendar allows

laynlo15 · 07-22-2017, 10:04 PM

It looks awesome. I love my lowered ss and you'll love your zl1

Bunksy · 07-23-2017, 03:20 AM

Looks great. And I love the pin strip around the splitters and side skirts - stunning, plus the bonnet and roof wrap. Did you think about wrapping the rear spoiler, too?

GoneBoy · 07-23-2017, 05:57 AM

very sharp looking car. Somehow you were able to pull off white, 2 shades of black, and red without it looking too busy. That, my friend, takes skills.

soceur77 · 07-23-2017, 09:45 AM

Looks awsome bro and i love the red pin striping you applied!

07-22-2017, 04:09 PM	#1
AZ Charlie Drives: 2017 ZL1 A10 Join Date: Jan 2012 Location: Arizona Posts: 308 View My Garage	2017 ZL1 Eibach Pro Kit Springs installed I had a great experience once again with Eibach and Rich, Mike and the team at DynoComp in Scottsdale, Arizona that performed all the work. I talked to them by phone to make sure I received the correct springs that would not affect my existing stock suspension but would lower the car to a satisfactory height. I am extremely pleased. Part number: E10-23-018-01-22 Some things I did while we had the wheels off: 1. Removed the large disc covers up front and installed the smaller covers. Since I live in Arizona and not my daily driver their is no need for me to have the larger disc covers. I installed the smaller disc covers that is recommended for track use so the rotors will get proper cooling. 2. I installed the ZL1 Add Ons rock guards on all four corners. This will be discussed in another thread and a complete build thread I will start on my car for forum friends to follow. 3. Since we should do a wheel alingment after replacing springs I went ahead and did the ZL1 Chevrolet specs for camber, caster and toe for track setup. Here are the specs: https://my.chevrolet.com/content/dam...tion-guide.pdf Per Eibach I should see a one inch drop in front and half inch drop in back. When we did the conversion at DynoComp in Scottsdale, AZ we were surprised how much better the car looked and it did look like it dropped the car significantly more than what Eibach stated but as you can see by the images Eibach was on point. Attached Images __________________ 2017 ZL1 A10 PDR NAV 2007 Lamborghini LP640 2010 Tundra Pre Runner 2012 Ford F450 Super Duty Prior cars: 2015 Z/28 Redline Motorsports SC725 (see profile for build details, Redline Motorsports youtube, Super Chevy article, etc) 2010 SS Supercharged with other mods...(two of this model) 2003 Lamborghini Murcielago (two of this model) 1998 Lamborghini Diablo SV 2004 Lamborghini Gallardo Ferrari 348 Spider Saleen Mustang

07-22-2017, 05:29 PM	#4
Infern0 Bring It Drives: In Between Join Date: Sep 2009 Location: San Antonio, TX Posts: 2,929 View My Garage	Love it. Accent pieces look great too. __________________ 2017 Camaro ZL1 M6 - Everything but the sunroof - Sold 2010 Camaro SS - 650RWHP Daily Driver - Traded

07-22-2017, 07:33 PM	#5
Stephen12ZL1 Drives: '21 ZLE A10 Join Date: May 2012 Location: Mechanicsville, VA Posts: 6,815	Very nice! __________________ '21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60' '17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold)

07-22-2017, 10:04 PM	#11
laynlo15 Drives: 2022 Lt1 A10 Join Date: Nov 2015 Location: clark, mo Posts: 8,862	It looks awesome. I love my lowered ss and you'll love your zl1 __________________ 2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff

07-22-2017, 04:39 PM	#2
USP45 Drives: 2017 ZL1 A10 Join Date: Aug 2016 Location: McKinney TX Posts: 334	Exactly what I have been looking at doing... have you noticed much difference in ride/handling? Might be too soon to answer that since you just had them installed...

07-22-2017, 04:42 PM	#3
Bow Tie Affair Drives: 6th. Gen ZL1 Join Date: Jan 2017 Location: Texas Posts: 424	What is the Eibach part number on the box?

07-23-2017, 03:20 AM	#12
Bunksy Drives: Gen 6 ZL1 White Join Date: Jul 2017 Location: Dubai Posts: 12	Looks great. And I love the pin strip around the splitters and side skirts - stunning, plus the bonnet and roof wrap. Did you think about wrapping the rear spoiler, too?

07-23-2017, 05:57 AM	#13
GoneBoy Drives: '17 ZL1 Join Date: Dec 2015 Location: Atlanta Posts: 410	very sharp looking car. Somehow you were able to pull off white, 2 shades of black, and red without it looking too busy. That, my friend, takes skills.

07-23-2017, 09:45 AM	#14
soceur77 Drives: 17 NFG ZL1 17 GTR 22 RS6 Join Date: Apr 2017 Location: Upper Marlboro MD Posts: 625	Looks awsome bro and i love the red pin striping you applied!

User Name		Remember Me?
Password