03-23-2013, 07:14 AM | #1 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
NH-SS brass vs Hurst updated bushing.
NH-SS brass vs Hurst updated bushing.
I have the brass bushing from NH-SS and have not installed It yet. Hurst is sending me a couple of there new updated nylon Bushing with o-rings. I only want to do this once. Pro and cons please.
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
03-23-2013, 07:28 AM | #2 |
BL1ZZRD
Drives: '16 Camaro 2SS, '20 Equinox Redline Join Date: Jul 2009
Location: Buffalo, NY
Posts: 7,840
|
I have the NH-SS brass bushing and it really made a big difference! Nice crisp shifts with nearly zero slop! The only drawback is increased buzzing and vibration during hard acceleration. I can't compare it to the Hurst bushings though so it's your call. Hopefully someone can chime in here that has installed them. The only thing that would worry me about the Hurst fix is that they are still NYLON! When I removed the original Hurst nylons they were toast! Hopefully the new nylon bushings are more durable! Good luck!
|
03-23-2013, 08:00 AM | #3 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
Maybe I should buy the MGW and be done with it. Hate to spend more cash.
Did you use the vibration tape on install. May help ?
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
03-23-2013, 08:50 AM | #4 |
BL1ZZRD
Drives: '16 Camaro 2SS, '20 Equinox Redline Join Date: Jul 2009
Location: Buffalo, NY
Posts: 7,840
|
I used the vibration pads on the upper shaft where the 2 bolt together. I didn't use the tape that they suggest on the lower linkage part because I didn't want it interfering with shift action. If you are in the market for a new shifter and haven't bought the Hurst yet save up for the MGW!
edit: I just noticed in you first post that you already have the Hurst. The MGW is a better set-up but it's pricy and you'd have to sell the Hurst! |
03-23-2013, 09:51 AM | #5 |
Drives: chevy Join Date: Jan 2011
Location: cleveland ohio
Posts: 847
|
Hurst really needs to make a better product I sold mine cheap because of the slop bought the lsr tri ax and no problem since and it adjustable
|
03-23-2013, 10:05 AM | #6 |
2010 Camaro 2 SS/RS M6
Drives: 2010 Camaro SS/RS Join Date: May 2009
Location: Clayton Delaware
Posts: 1,218
|
Mgw FTW
__________________
Forged LS3, FED M311 heads, CAI Inc, ARH 1 7/8, Corsa Xtreme, Taylor Wires, MGW Shifter, Street slayer twin carbon clutch, Tick braided clutch line & speed bleeder, ZL1 Diff Swap, BMR Split drop, Sway Bars, Trailing Arms, Toe Rods, Pro bushing kit, Carslyle racing 15in conversion, Whipple, LPE dual fuel pumps, Rx catch can, Id1300x, Alky Control
|
03-23-2013, 03:01 PM | #7 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
Yes I have the hurst installed. Also have the fix brass bushing and the hurst updated on it way. Neither installed yet. Which to use?
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
03-23-2013, 04:31 PM | #8 |
|
If it were me, I would go with the brass bushing. If you only want to do it once, use the one you KNOW will fix the problem, not the one you hope and think might fix the problem.
__________________
ProCharger P1X, Vengeance Racing Kaotic Cam, ARH Headers and Exhaust with Borla ATAK mufflers, MGW Shifter, MTI Drop Springs, Forgeline RB3C Wheels, 3.91 gears, Night Owl LED Control System
|
03-23-2013, 06:09 PM | #9 |
BL1ZZRD
Drives: '16 Camaro 2SS, '20 Equinox Redline Join Date: Jul 2009
Location: Buffalo, NY
Posts: 7,840
|
1) MGW
2) Brass 3) Hurst nylon |
03-25-2013, 05:23 AM | #10 |
Drives: 11 IBM n White 2SS/RS M6 Join Date: May 2011
Location: Tewksbury Ma
Posts: 358
|
Forget about nylon bushings from Hurst
Install the NH-SS improved bushing Making sure yo burnish it If you dont like it then move off to the MGW Jus-saying the NH-SS bushings does make that much of an improvement I have 5k miles on mine Hurst with NH-SS bushing still tight no slop Sent from my DROID X2 using Tapatalk 2
__________________
Black CIA -Powder Coated Red Air Scoop - Vmax Ported Throttle Body - Ceramic Coated Dynatek Headers - High Flow Cats out thru factory Cat Back - JRE rough idle cam package - Trunion Upgrade - Valve Springs - Hardened Push rods - 3 bolt timing gear - SLP Under drive pully- Washer bottle relo kit - Hurst Short Throw Shifter with updated pin bushing from C5 member NH-SS - IdealG's improved Master Cylinder - GTO Clutch reservoir - L99 Brake Reservoir - Stainless Braided clutch line - wrapped up with a JRE Tune My SS layed down 462 hp on JRE's Superflow Dyno
|
03-25-2013, 06:51 AM | #11 |
Drives: 2010 2SSRS headers/CAI/tune/corsa, Join Date: May 2010
Location: Commerce twp Michigan
Posts: 1,413
|
RogerBzSS
? Any vibration noise.
__________________
Stainless works headers/cats Roto fab CAI /
Corsa install and tune Livernois TSW Nuburgring 9 &10" x 20 on Invos (315 & 275 ) JL Audio XD400/4 amp Pfadt trailing arms & tie rods sway bars. pedders street 1 package. ,Hurst short throw shifter With bronze bushings . |
03-25-2013, 07:18 AM | #12 |
Drives: 11 IBM n White 2SS/RS M6 Join Date: May 2011
Location: Tewksbury Ma
Posts: 358
|
extreemly minor vibration IMPO
I feel it when I ride with the shifter as a hand rest Noise No..
__________________
Black CIA -Powder Coated Red Air Scoop - Vmax Ported Throttle Body - Ceramic Coated Dynatek Headers - High Flow Cats out thru factory Cat Back - JRE rough idle cam package - Trunion Upgrade - Valve Springs - Hardened Push rods - 3 bolt timing gear - SLP Under drive pully- Washer bottle relo kit - Hurst Short Throw Shifter with updated pin bushing from C5 member NH-SS - IdealG's improved Master Cylinder - GTO Clutch reservoir - L99 Brake Reservoir - Stainless Braided clutch line - wrapped up with a JRE Tune My SS layed down 462 hp on JRE's Superflow Dyno
|
03-25-2013, 07:20 AM | #13 |
Drives: 2013 Chevy Truck Join Date: Mar 2010
Location: Copperas Cove, Texas
Posts: 1,782
|
where did you purchase the brass bushing from? I have the hurst and did not want to bother with the updated Hurst bushing because I knew it was still nylon.
__________________
Texas speed LT Headers and High Flow Cats, Magnaflow 3 inch cat-back Exhaust, SNL V2 Comp CAM, Texas Speed Underdrive Pully, G5CR CAI, Hurst Short Throw Shifter, JetFlo Mass Air Sensor, Custom Grill, Amber AAC Headlight and Fog Light Halo, Amber footwell Lighting, Amber under hood lighting, RK Sport Ram Air /Heat Extractor Hood and ADM Racing Scoop. 447.9 RWHP 428 TQ
My car is exactly that, No one has to like it but me! |
03-25-2013, 07:23 AM | #14 |
Drives: 11 IBM n White 2SS/RS M6 Join Date: May 2011
Location: Tewksbury Ma
Posts: 358
|
See Here
http://www.camaro5.com/forums/showthread.php?t=226328 The Material that NH-SS uses is actually a split 2 piece bushing made from oilite bronze
__________________
Black CIA -Powder Coated Red Air Scoop - Vmax Ported Throttle Body - Ceramic Coated Dynatek Headers - High Flow Cats out thru factory Cat Back - JRE rough idle cam package - Trunion Upgrade - Valve Springs - Hardened Push rods - 3 bolt timing gear - SLP Under drive pully- Washer bottle relo kit - Hurst Short Throw Shifter with updated pin bushing from C5 member NH-SS - IdealG's improved Master Cylinder - GTO Clutch reservoir - L99 Brake Reservoir - Stainless Braided clutch line - wrapped up with a JRE Tune My SS layed down 462 hp on JRE's Superflow Dyno
Last edited by RogerBzSS; 03-25-2013 at 07:35 AM. |
|
|
|
|