You are browsing camaro5 
 |
|
01-31-2010, 09:04 PM
|
#1 |
 Drives: 2010 Summit White Camaro SS Join Date: Jan 2010
Location: Phoenix
Posts: 35
|
How To Remove Stock Spoiler And Install Sawtooth?
Hey everyone, I am going to buy the Sawtooth spoiler for my Camaro. I was just wondering, how do I remove the stock spoiler, and how do I install the Sawtooth? Any installation guides or write-ups would be helpful.
Thanks 
|
|
|
|
01-31-2010, 09:15 PM
|
#2 |
 
Drives: 2010 IOM SS/RS, 69 Camaro Join Date: Nov 2008
Location: Douglasville, Georgia
Posts: 563
|
I don't know about the sawtooth but to remove your factory spoiler, there are six nuts. You can see the four plastic caps for the two left and two right nuts. for the other two, you have to remove some of your plastic discs to look under the trunk lid felt where you will find the other two. Be careful because you can lose these down inside the trunk lid. The spoiler may be hard to pull off due to the studs binding against the holes and there is also an alignment pin. Just work it loose carefully.
__________________
R6P - Kooks 1-7/8 Catted LT Headers, Roto-Fab CAI, MGW Shifter, Revolution SS Front Spoiler, Unrestricted Motorsports Rear Spoiler, Razzi Side and Rear EFX, Heritage Grill, Hawk HPS Pads, G2 Matched Calipers, SAV-3 Wheels, Vengeance Racing Stage II Cam 227/239.614/.624 115+3, 25% Underdrive Pulley, Oil Catch Can, 461 RWHP - 420 Torque
|
|
|
|
|
05-06-2011, 05:14 AM
|
#3 |
|
2010 Camaro SS/RS
Drives: 2010 Camaro SS/RS Join Date: Jan 2011
Location: Elk Grove CA
Posts: 155
|
Hope you bought the ORIGINAL that mounts with the factory holes. The CHEAP eBay knockoff is shorter then the stock and shows the holes when mounted.... I know I have BOTH!
|
|
|
|
|
05-06-2011, 05:24 AM
|
#4 |
 
Drives: 2010 2SS/RS L99 RJT/Black Join Date: Feb 2011
Location: Mechanicsville, VA
Posts: 375
|
__________________
 USAF Retired 1994 |
|
|
|
|
01-06-2012, 09:27 AM
|
#5 |
Drives: 2010 Camaro 2SS - Black on Black Join Date: Aug 2010
Location: Jackson, TN
Posts: 731
|
Ok so I am removing my spoiler to install the NLP aftermarket dovetail...while I was removing the 6th and final bolt my socket came off and fell inside the trunk lid panels. My only idea so far is to back my car on my steep driveway incline and see if it will roll to the end where I can grab it thru the bolt access holes. Any other ideas?
__________________
 |
|
|
|
|
01-06-2012, 09:51 AM
|
#6 |
|
Drives: 2013 WRX Sedan Join Date: Aug 2009
Location: Austin, TX
Posts: 705
|
A super-long magnet?
|
|
|
|
|
01-06-2012, 10:26 AM
|
#7 |
|
Drives: 2010 Camaro 2SS - Black on Black Join Date: Aug 2010
Location: Jackson, TN
Posts: 731
|
Anyone know where to find a flexible snake magnet?
__________________
|
|
|
|
|
01-06-2012, 11:01 AM
|
#8 | |
  
Drives: BLACK 2SS/RS Join Date: Sep 2009
Location: Florida
Posts: 1,092
|
Quote:
I have seen long flexible handles (16" or so) with a magnet on the end. Check some auto parts stores. Last resort would be to remove trunk lid.
__________________
CCW polished 505a's
Front 20x10 w/275/40/20's Rear 20x11.5 w/305/35/20's Eibach 1" Pro Spring Kit Factory GFX MPD1 spoiler painted bowties 15% tint |
|
|
|
|
|
01-06-2012, 11:04 AM
|
#9 | |
|
Drives: 2010 Camaro 2SS - Black on Black Join Date: Aug 2010
Location: Jackson, TN
Posts: 731
|
Quote:
yeah I found a few online at Advanced Auto Parts. might not be a bad thing to have laying around for such occasions...
__________________
|
|
|
|
|
|
01-06-2012, 11:04 AM
|
#10 |
Drives: CGM 2SS/RS, 1987 & 2014 Silverado Join Date: Oct 2010
Location: Spencerport, NY
Posts: 1,012
|
My garage
 I got mine from Harbor Freight.  How about trying a shop vac?
__________________
 |
|
|
|
|
01-06-2012, 11:07 AM
|
#11 |
    
Drives: 2011 Camaro 2SS/RS (Black) L99 Join Date: Aug 2010
Location: Pilot Point, Texas
Posts: 2,185
|
sawtooth?
__________________
 Follow me on Instagram @C7Corvettes |
|
|
|
|
01-10-2012, 08:28 AM
|
#12 | |
|
gmans 10
|
Quote:
__________________
k&n intake,borla catback
trifecta tune, doug thorley headers |
|
|
|
|
|
01-10-2012, 08:39 AM
|
#13 |
 
|
I got the cheap one from ebay ($116 shipped). Doesn't line up exactly w/existing holes but it's close enough you wouldn't notice if I didn't point it out. Didn't drill extra holes for the 2 middle posts (in case I want to change back. Filled in unused holes w/silicone so they wouldn't leak.
__________________
![C][SIGPIC]](image.php?s=c5c7bd80d0643d157ab4dcf77c353e3f&u=50984&type=sigpic&dateline=1321558757) Going as fast as my accountant will let me! |
|
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 2010 Camaro Pre-Painted CDC Rear Spoiler! All Camaro Colors Available! | RPI Designs | Exterior Parts & Accessories | 42 | 12-09-2017 12:47 PM |
| New from RPI! 2010 Camaro Pre-Painted Body Color Rear Spoiler! $399.00, painted! | RPI Designs | Exterior Parts & Accessories | 10 | 03-25-2010 03:42 PM |
| Anyone have this chin spoiler or this rear spoiler? | gtothep123 | Cosmetics and Lighting Modification Discussions | 6 | 01-31-2010 09:16 PM |
| Spoiler install hose my stripes? | lostinvt | Cosmetics and Lighting Modification Discussions | 12 | 08-24-2009 03:13 PM |
| Spoiler LPOs questions about install | thecamaroguy | Camaro Price | Ordering | Tracking | Dealers Discussions | 2 | 10-23-2008 08:44 AM |
