Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com - Tom Henry Racing THR22 2010/LS3/IBM/Supercharged SS Camaro [COTW 10/29/12]

:iono:

What ever happened to the real car guys? They weld the exhaust in place so they don't have to worry about a little scrape here and there and they knew the :rules: -- exhaust, headers and cats are SELF CLEARANCING. As for front and side fascias they keep painted spares in the garage painted and ready to go. :thumbup: If they even contemplated racing they knew their car couldn't possibly be low enough if it didn't throw sparks when you hit the brakes let alone the little bumps in the gas station.

There is no whining or complaining if you own a Muscle Car :paddle:

This is the end of this Public Service Announcement.

the 45* is in reference to not plowing the front end into any gradient more than 1* - not some pansy gas filing ports :thumbsup:

ya know... for the guys who actually went that low ;)

Mr Twisty

06-16-2012 09:28 AM

Looks good with the stock upper grill and ZL1 lower :thumbsup:

JusticePete

06-16-2012 01:29 PM

Quote:

Originally Posted by zebra (Post 5136404)

the 45* is in reference to not plowing the front end into any gradient more than 1* - not some pansy gas filing ports :thumbsup:

ya know... for the guys who actually went that low ;)

Why would Chris need a 45 degree approach angle when he drives THIS?

http://www.camaro5.com/forums/attach...2&d=1338928722

garcmol

06-16-2012 03:51 PM

Quote:

Originally Posted by mlee (Post 5135563)

...but mine was faster...;)

You got me there! :laugh:

speedster

06-16-2012 05:24 PM

Hey, I bet you could sell those up north as High Performance 'snow removal' equipment. What a deal for local municipalities. What used to take a truck 3 hours can now be done with a THR Camaro in 45 minutes...:D

Quote:

Originally Posted by JusticePete (Post 5137399)

Why would Chris need a 45 degree approach angle when he drives THIS?

http://www.camaro5.com/forums/attach...2&d=1338928722

600hp-lpe

06-16-2012 09:28 PM

Quote:

Originally Posted by JusticePete (Post 5135874)

What ever happened to the real car guys? They weld the exhaust in place so they don't have to worry about a little scrape here and there and they knew the :rules: -- exhaust, headers and cats are SELF CLEARANCING. As for front and side fascias they keep painted spares in the garage painted and ready to go. :thumbup: If they even contemplated racing they knew their car couldn't possibly be low enough if it didn't throw sparks when you hit the brakes let alone the little bumps in the gas station.

There is no whining or complaining if you own a Muscle Car :paddle:

This is the end of this Public Service Announcement.

Chris...sick MRS. GTAHAVIT on DEB. That'll get Pete to FLY STRAIGHT...:yikes:

He just cost you.. about $6-7K in spare, throw away parts (according to Pete's replacement swap policy, above).

Self clearanceing exhausts in the old days were 2 hundred bucks. Not on today's Camaro.. and you havn't even swapped the front end yet.

BAD BAD BAD!!!!

Redemption

06-16-2012 09:36 PM

Quote:

Originally Posted by 600hp-lpe (Post 5138965)

Qft

Oh snap. Just Got real in here!!

speedster

06-17-2012 08:16 AM

Quote:

Originally Posted by 600hp-lpe (Post 5138965)

I remember flattening two of the primary pipes on a set of headers during a 'clearance' run. Back then, you went to a welding shop, they cut out the flat pieces and welded in new pipes. Heck on those Hooker Super Competition headers, the welding shop replaced that section with roll cage tubing. Never had them bend there again... :bellyroll:

600hp-lpe

06-17-2012 11:56 AM

My '67 Camaro would jack the wheels in 2nd and 3rd gear 2feet off the ground.. sending sparks on landing from the exhaust. I had spare headers and swapped them like oil changes. No problem at around $100 a pair.

Those were the good old days...

JusticePete

06-17-2012 03:19 PM

Do it like the pros and use carbon fiber protection. http://www.dragonplate.com/ecart/categories.asp?cID=127

GTAHVIT

06-18-2012 10:53 AM

Quote:

Originally Posted by 600hp-lpe (Post 5138965)

I know!! :D I don't have it yet to swap... :(

Quote:

Originally Posted by JusticePete (Post 5141527)

Do it like the pros and use carbon fiber protection. http://www.dragonplate.com/ecart/categories.asp?cID=127

There is a whole 'nother level you can go to isn't there....