Electric Window problem - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Eulogy · 10-17-2009, 08:25 AM

I disconnected my battery to install a catback and CA intake. I finished my business and reconnected the battery.
The once automatic slight roll up or roll down when the door is opened is missing now. The door will not shut properly now. I plan on taking it to the dealer, but would like to avoid that if necessary Any suggestions?.

Eulogy · 10-17-2009, 08:35 AM

I found this post:

Try this procedure from the manual:

1. With the ignition in ACC/
ACCESSORY, ON/RUN,
or when Retained Accessory
Power (RAP) is active, close
all doors.
2. Press and hold the power
window switch until the window
is fully open.
3. Pull the power window switch up
until the window is fully closed.
4. Continue holding the switch up
for approximately two seconds
after the window is completely
closed.
The window is now reprogrammed.
Repeat the process for the other
window.

Haha,it worked!

Wileytrigger21 · 10-17-2009, 08:41 AM

Now this is the kind of helpful post that I luv!!!!!

Kudos Eulogy!!!

Just Jim · 10-17-2009, 08:44 AM

Try this from page 1-16 of the owner's manusl.

Programming the Power Windows

If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work.

Before reprogramming, replace or recharge the vehicle’s battery.

To program each front window, follow these steps:

1. With the ignition in ACC/ACCESSORY, ON/RUN, or when Retained Accessory Power (RAP) is active; close all doors.

2. Press and hold the power window switch until the window is fully open.

3. Pull the power window switch up until the window is fully closed.

4. Continue holding the switch up for approximately two seconds after the window is completely closed.

The window is now reprogrammed. Repeat the process for the other windows.

10-17-2009, 08:25 AM	#1
Eulogy Drives: 2010 Camaro Join Date: Oct 2009 Location: Va Beach Posts: 2	Electric Window problem I disconnected my battery to install a catback and CA intake. I finished my business and reconnected the battery. The once automatic slight roll up or roll down when the door is opened is missing now. The door will not shut properly now. I plan on taking it to the dealer, but would like to avoid that if necessary Any suggestions?.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2010 Camaro Rear Window Lower Window Seal Improperly Installed at Delivery/Fix	Alan C. Higgs	Camaro Issues / Problems \| Warranty Discussions \| TSB and Recalls	14	03-11-2011 04:35 PM
window tint questions...	haleyd	5th Gen Camaro SS LS LT General Discussions	11	08-16-2009 12:02 AM
Window Indexing	Merlin1187	Camaro Issues / Problems \| Warranty Discussions \| TSB and Recalls	4	07-13-2009 09:07 PM
Somewhat Annoying Back Seat Problem!	ZNOLMT	5th Gen Camaro SS LS LT General Discussions	5	06-21-2009 10:22 AM
Problem with my v6	TonytheTiger	4th Generation Camaros	12	08-22-2008 03:34 PM

10-17-2009, 08:35 AM	#2
Eulogy Drives: 2010 Camaro Join Date: Oct 2009 Location: Va Beach Posts: 2	I found this post: Try this procedure from the manual: 1. With the ignition in ACC/ ACCESSORY, ON/RUN, or when Retained Accessory Power (RAP) is active, close all doors. 2. Press and hold the power window switch until the window is fully open. 3. Pull the power window switch up until the window is fully closed. 4. Continue holding the switch up for approximately two seconds after the window is completely closed. The window is now reprogrammed. Repeat the process for the other window. Haha,it worked!

10-17-2009, 08:41 AM	#3
Wileytrigger21 Drives: 2010 CGM 2LT / RS, Blk 1SS/RS Join Date: Sep 2009 Location: TEXAS Posts: 404	Now this is the kind of helpful post that I luv!!!!! Kudos Eulogy!!!

10-17-2009, 08:44 AM	#4
Just Jim Drives: 2010 Camaro SS Join Date: Jan 2009 Location: Sarasota, FL Posts: 19	Try this from page 1-16 of the owner's manusl. Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, replace or recharge the vehicle’s battery. To program each front window, follow these steps: 1. With the ignition in ACC/ACCESSORY, ON/RUN, or when Retained Accessory Power (RAP) is active; close all doors. 2. Press and hold the power window switch until the window is fully open. 3. Pull the power window switch up until the window is fully closed. 4. Continue holding the switch up for approximately two seconds after the window is completely closed. The window is now reprogrammed. Repeat the process for the other windows.