01-27-2018, 08:42 PM | #1 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
fuel line flip
did it and my fuel line (part number 10401798) is 3 inches TOO SHORT! got the part number off here in the dyi section. what should I do? spent a hundred bucks on the line. not chicken feed. any help or part number for a longer one would be greatly appreciated. 2014 1ss/ls3. the oldman....
|
01-27-2018, 09:00 PM | #2 |
Drives: 2011 convertible 2ss/rs Join Date: Sep 2015
Location: Houston
Posts: 971
|
Get roughly 18 feet and cut when done routing
Sent from my SM-N950U using Tapatalk |
01-27-2018, 09:06 PM | #3 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
just the short piece from hard line to fuel rail. checked here in other places and the c5 line might be longer anybody have that part number or experience with this ? a previous thread said to take the plastic clip loose on the fuel line but I'm not hip to that tune.
|
01-27-2018, 09:51 PM | #4 |
Geoff
Drives: 2020 ZL1 Green Join Date: May 2013
Location: Houston
Posts: 1,733
|
The Corvette line is short for 2013 and up, may be 12s too. Need to release the hard fuel line from the frame rail to make it fit
An alternative is to add a flex fuel sensor so the Vette line works
__________________
|
01-27-2018, 09:56 PM | #5 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
will I be able to support the hard line else where?
|
01-27-2018, 09:57 PM | #6 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
figure I might go to a used car lot and pop some hoods to see what might be long enough
|
01-28-2018, 01:22 AM | #7 |
Drives: 2012 SS/RS MN6 Join Date: Mar 2016
Location: Covington Ga
Posts: 783
|
You need the return line from a C5 Corvette.
|
01-28-2018, 06:46 AM | #8 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
thanks 0331 marine, thanks for your service also! have a young marine as my apprentice right now. trying to teach him as much as I can before I retire. the oldman........
|
01-28-2018, 07:11 AM | #9 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
next question; part number for said return line,PLEASE.
|
01-28-2018, 10:55 AM | #10 |
old school chevy rodder
Drives: 2013 2SS/RS Manual,DM exhaust,CRT Join Date: Jul 2012
Location: Oregon
Posts: 5,587
|
there used to be a vendor on here that specialized in the parts to do the fuel line flip BTW, you might be able to check fuel rail flip or other key words to find them I have way too many saved favorites............
__________________
2021 Wild Cherry ZL1 A10, Sunroof, Data, Carbon, Nav, RotoFab Dry CAI, Elite x2, Borla ATK, Driveshaft shop
|
01-28-2018, 01:23 PM | #11 | |
Drives: 2012 SS/RS MN6 Join Date: Mar 2016
Location: Covington Ga
Posts: 783
|
Quote:
You can still get them on eBay. There's a set on there now for $70. |
|
01-28-2018, 05:12 PM | #12 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
thanks, once again, you folks. taking my valve covers and brackets to the powder coater tomorrow, its behind a chevy dealer . i'll get them to do a dealer search. I did that when I went 6 spd for my 02' dealer found me what they call a number 6 boot in Puerto rico back In 10' I wiil look on e-bay thanks,
|
|
|
|
|