What Did You Do To Your Camaro Today? - Page 1582 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

SSMY1LE · 04-19-2019, 10:25 AM

-Bronze solid Trunion Upgrade
-Valve springs/retainers/locks
-Valve seals
-Oil/filter change
-Trans fluid change (Redline D4)
-Rear end fluid change (Redline 75W90)

Arogg · 04-19-2019, 10:45 AM

Pics of the Calipers as promised. I originally had them plastidipped purple metallic and I had purple metallic stripes. Then I switched to Blue metallic. Now my whole car is going a mixture of gloss black / Flat black / and Gloss Red. Im loving this setup so far.

davesnever · 04-19-2019, 03:27 PM

Quote:

Originally Posted by grandpamike

yeah is just some body filler/bondo. no problems, I just roughed it up a bit and put some bondo on it and let it dry then sanded it. I should have sanded it a bit better but it is hardly noticeable. I plan on getting the actual stripes. I made these myself.

Well it looks a lot better and I will probably do the same here, thanks!

Cheap Guy · 04-19-2019, 03:47 PM

Quote:

Originally Posted by Arogg

Ordered a heritage grille, 6th gen Redline Camaro Badges, new R1 Concepts Rotors/Pads, and BMR Lowering springs! Last week I finally refinished my calipers to Red with the G2 kit. Ill post some pics of those later. ITS MOD SEASON!!

Did you get an OEM grille? If so, how much and where? If not, let us know how it fit when you install it.

George-CZ · 04-19-2019, 04:01 PM

A little trip with my girlfriend...
1978 is slower, but horsepower is comparable with 2010
We enjoyed it very much

Arogg · 04-19-2019, 04:31 PM

Quote:

Originally Posted by Cheap Guy

Did you get an OEM grille? If so, how much and where? If not, let us know how it fit when you install it.

Nah, couldn't find an OEM one. I bought one of the ebay knockoffs that have started popping up. ive already seen a few posts saying the quality is good. Ill post pics as I start receiving and installing all the upgrades

George-CZ · 04-21-2019, 04:44 PM

Again, I made a little progress in working on the HURST custom shifter.
The original hole with a nonsensical slope of the thread blinded, sanded, polished and drilling a new smaller threaded hole.

He made a piece between the handle and the cuff.

..just it looks better.

Just a powder paint shop and I can mount it in the car.

grandpamike · 04-21-2019, 06:59 PM

Putting a splitter on the car. Painted it today. will buff it out tomorrow and get in put on the car.

Mike14bumblebee · 04-21-2019, 11:59 PM

Quote:

Originally Posted by SSMY1LE

-Bronze solid Trunion Upgrade
-Valve springs/retainers/locks
-Valve seals
-Oil/filter change
-Trans fluid change (Redline D4)
-Rear end fluid change (Redline 75W90)

How many kms do you have on ur cam that your replacing the trunions, springs, etc? I no urs is a manual but how do you feel about the Howard's cam so far?

Panda1LE · 04-22-2019, 02:28 AM

My emblem pros hood badge

Tabes · 04-22-2019, 12:42 PM

Dropped the car off at Speed Inc to install my Magnuson supercharger.

LINYSS · 04-22-2019, 04:29 PM

Quote:

Originally Posted by Tabes

Dropped the car off at Speed Inc to install my Magnuson supercharger.

You Will LOVE IT!

Tajefe Couple · 04-22-2019, 04:46 PM

Quote:

Originally Posted by Panda1LE

My emblem pros hood badge

Those look really nice on your beautiful car match perfect!

Deputy347k9 · 04-22-2019, 10:06 PM

Quote:

Originally Posted by Deputy347k9

Just finished a great detailing of my 2014 Camaro. Once I finish reading Forum posts I am hitting the rack and will be on the road at 0400. I decided to treat myself to a few days on the road, first stop will be a couple of days in Gettysburg, Pa touring. From there it's onto NJ and NYC to be with a great bunch of friends the "Hired Guns". Hired Guns is a police motorcycle club with our mother chapter in NJ. The plan is a safe trip behind the wheel of the Camaro. Just in case I put her bra on, don't want any chips! So I will get back with you folks on the flip side next Sunday or Monday. Larry

Arrived back home Saturday evening. Total trip saw the Camaro adding just a bit over 2K miles. It was nothing less than a pleasure. Scary at times, especially around Washington DC and NYC... OMG you move your butt around in the seats, apply a firm grip on the steering wheels and shout it out, "come on you bastards, bring it on!

This week she is do an oil change and I will schedule her for a front end alignment just in case the couple of pot holes I hit did jar her out a tad.

Gas... well NC and VA were not to bad, PA, NJ NY was another story as was the tolls. Overall I had a killer trip, loved it.

The girl wore her bra the entire time, tomorrow I will wash the 182,312 bugs off then removed and put her away for next trip. Then it's back to detailing her again.

04-19-2019, 10:25 AM	#22135
SSMY1LE Drives: '14 1LE RS NPP Recaro Join Date: Dec 2013 Location: YYZ Posts: 1,676 View My Garage	-Bronze solid Trunion Upgrade -Valve springs/retainers/locks -Valve seals -Oil/filter change -Trans fluid change (Redline D4) -Rear end fluid change (Redline 75W90) __________________ '14 1LE, Recaro, Cammed, Headers, Hi Flows, CAI, Tuned, 486 RWHP https://www.youtube.com/watch?v=H57UfKCO0EY&feature=youtu.be Last edited by SSMY1LE; 04-19-2019 at 10:56 PM.

04-19-2019, 10:45 AM	#22136
Arogg A legend in his own mind Drives: 2010 2SS/RS M6 Join Date: May 2013 Location: Long Island, New York Posts: 917	Pics of the Calipers as promised. I originally had them plastidipped purple metallic and I had purple metallic stripes. Then I switched to Blue metallic. Now my whole car is going a mixture of gloss black / Flat black / and Gloss Red. Im loving this setup so far. Attached Images __________________ 2010 2SS/RS "The Mistress" Color matched OEM GFX / VIS Carbon Fiber Hood (absolute trash quality and customer service ) / Heritage Grille / 5% Windows / 30% Windshield tint with 5% visor strip / Tinted Exterior Lights / Streetfighter LA Spoiler / Morimoto XB LED fogs / LED sidemarkers / Airaid CAI / Hurst Short Throw / TSP LT's / No cats / No resonator / Corsa Xtreme Catback / Trifecta Tune / Factory amp replaced / 2 JL Audio 12's / MRR 228 Wheels / BMR Springs / Koni Yellows / R1 Concepts Rotors & Pads 2006 Dodge Magnum RT "The daily"

04-21-2019, 06:59 PM	#22142
grandpamike Drives: 2014 2lt rs Join Date: Nov 2017 Location: georgia Posts: 90	Putting a splitter on the car. Painted it today. will buff it out tomorrow and get in put on the car. Attached Images

04-22-2019, 02:28 AM	#22144
Panda1LE Drives: 2013 2SS/RS 1LE (6spd) Join Date: Mar 2018 Location: Temecula, CA Posts: 281	My emblem pros hood badge Attached Images __________________ CAI intake, Stainless Power LTH, SCT X4, NPP exhaust

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GM memo to dealers	Moose	5th Gen Camaro SS LS LT General Discussions	41	02-04-2010 08:33 PM
Major Pedders Event in Houston! Saturday, Jan 30th! Meet DMS	Info@PeddersUSA.com	USA - Texas	39	02-01-2010 01:48 PM
Answeres to questions I have stumbled on	dieseldave24v	5th Gen Camaro SS LS LT General Discussions	13	02-23-2009 07:56 PM

04-19-2019, 04:01 PM	#22139
George-CZ Drives: 2010 2SS LS3 and 1978 STROKER 383 Join Date: Feb 2018 Location: Czech Republic Posts: 1,611	A little trip with my girlfriend... 1978 is slower, but horsepower is comparable with 2010 We enjoyed it very much

04-21-2019, 04:44 PM	#22141
George-CZ Drives: 2010 2SS LS3 and 1978 STROKER 383 Join Date: Feb 2018 Location: Czech Republic Posts: 1,611	Again, I made a little progress in working on the HURST custom shifter. The original hole with a nonsensical slope of the thread blinded, sanded, polished and drilling a new smaller threaded hole. He made a piece between the handle and the cuff. ..just it looks better. Just a powder paint shop and I can mount it in the car.

04-22-2019, 12:42 PM	#22145
Tabes Drives: 2013 2SS camaro convertible L99 Join Date: Apr 2016 Location: chicago Posts: 106 View My Garage	Dropped the car off at Speed Inc to install my Magnuson supercharger.