What Did You Do To Your Camaro Today? - Page 1639 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

X77-69z28 · 10-26-2019, 09:20 AM

Pushed the 69 and 70 outside to finally finish sheet rocking the ceiling in my garage!

Leo72793 · 10-27-2019, 10:43 AM

Picking a new wheel color for my M017 because MRR wheels paint is so brittle. No curbing or acidic washes and the paints liteally chipping off. No pressure washing either. Im thinking this https://www.prismaticpowders.com/gal...kingsport-grey

GearheadSS · 10-28-2019, 09:33 AM

New rotors and pads. OEM rotors with Powerstop Extreme Z26 pads.

15RS2NV · 10-30-2019, 12:06 AM

Ordered some toys:
- Overkill 80mm Throttle Body
- Accel ignition coils
- Intake manifold spacer insulator (MACE)
- Made an appointment to get intake manifold ported

They start coming in Friday so she'll be in the garage for a week or two.

Leo72793 · 11-01-2019, 06:12 PM

Debating on either 2 10 boston acoustics 10.4LF old schools or s ingle Alpine 10 X series new 2019 sub

Spec · 11-01-2019, 09:02 PM

Got it fixed! Can't wait to have some fun again with my ride this weekend!! First a nice thorough wash! Then, the sky's the limit.

Leo72793 · 11-01-2019, 10:47 PM

Quote:

Originally Posted by Spec

Got it fixed! Can't wait to have some fun again with my ride this weekend!! First a nice thorough wash! Then, the sky's the limit.

Still love those wheels! What broke?

Spec · 11-01-2019, 11:00 PM

Quote:

Originally Posted by Leo72793

Still love those wheels! What broke?

Nothing broke thank goodness. But had some suspension shaking that started a few weeks ago, progressively getting worse. Turned out to be badly worn out lower control arm bushings. I swapped all of the front end bushings to BMR years ago.

https://s3.amazonaws.com/shopware.at...mp4?1572542588

Leo72793 · 11-01-2019, 11:24 PM

Quote:

Originally Posted by Spec

Nothing broke thank goodness. But had some suspension shaking that started a few weeks ago, progressively getting worse. Turned out to be badly worn out lower control arm bushings. I swapped all of the front end bushings to BMR years ago.

https://s3.amazonaws.com/shopware.at...mp4?1572542588

I feel you there. I had a spring isolator go bad and was insanely difficult to drive. Rear wheel bounced a heck of a lot. Now i have an axle seal leaking from it. New parts are here thankfully (seals and axle nuts)

lemontwist · 11-03-2019, 05:05 PM

did the frameless mirror thing.i found this video to be the best guide,and i would like to add the color HUD upgrade is cool while i had my dash out i put 1 in it came from a ZL1 for what that's worth. i got it from https://www.hawksmotorsports.com/ for 150 shipped. i find myself on the page with the g-meter and the shift light arrows all the time.

SS_CTS-V · 11-04-2019, 03:00 PM

Just a little vinyl work on Sunday afternoon. Not my design, but I did have to tweak it a bit to fit the window as well as flip everything for the other side. Nothing special, just a Cricut machine and some basic graphics work.

Name: thumbnail_IMG_0523.jpg
Views: 515
Size: 91.1 KB

Name: thumbnail_IMG_0523.jpg
Views: 515
Size: 91.1 KB

redcoats1976 · 11-04-2019, 03:16 PM

good to see you back on the road and out of the dumps spec.all i did to mine was fix a few paint chips today.next monday its gotta go to the dealer,engine light is on.something in the emissions system is gone bad...

Spec · 11-05-2019, 06:25 PM

Quote:

Originally Posted by redcoats1976

good to see you back on the road and out of the dumps spec.all i did to mine was fix a few paint chips today.next monday its gotta go to the dealer,engine light is on.something in the emissions system is gone bad...

Thanks bro! Be careful with 'dem dealers.......

15RS2NV · 11-07-2019, 11:14 PM

Well, this is more of a "what have i done with your Camaro this week". I ordered and received the Overkill 80mm throttle body, MACE Engineering 1" intake manifold insulator (spacer), and had them and the intake manifold sent out to have the intake manifold fully ported and matched to the TB and the insulators to all match the manifold and engine.

Not being happy sitting around waiting, I'm sanding the camshaft covers (where valve covers are on V8s) and polishing. Not leaving well enough alone, I'm not sanding and polishing the water pump and brackets along the front of the engine.

10-26-2019, 09:20 AM	#22933
X77-69z28 Drives: 69 Z/28, 70 Z28, 99SS, 15 Z/28 2018 Join Date: Sep 2016 Location: Long Island, NY Posts: 407	Pushed the 69 and 70 outside to finally finish sheet rocking the ceiling in my garage! __________________ Buddy 69 Z/28 burnished brown, m-21 owned since 1978 70Z/28 forest green M40 CE block PROJECT 99 SS hugger orange 6spd no t-tops 1 of 54 15 Z/28 white AC, radio

10-27-2019, 10:43 AM	#22934
Leo72793 Drives: 2011 2SS/RS Join Date: Feb 2016 Location: Jacksonville FL Posts: 1,227	Picking a new wheel color for my M017 because MRR wheels paint is so brittle. No curbing or acidic washes and the paints liteally chipping off. No pressure washing either. Im thinking this https://www.prismaticpowders.com/gal...kingsport-grey __________________ •2011 Camaro SS 2SS/RS A6 •MRR M017 1le Replica Wheels •Vararam Ram Air Intake •Speed Engineering Longtube Headers w/ Magnaflow HF Cats •Bo White PnP Stage 2 TB •GPI SS2 VVT Cam w Cometic thin gaskets 10.69 compression •Xpipe w/ Res Delete and NPP Exhaust •Tuned By Anonymous Calibrations •Gen5DIY Mylink Conversion W/ Backup Cam •Morel 3 way custom speakers, Infinity 860w Subwoofers in trunk baffle •Helix P6 6ch amp w/ 8ch DSP and P1 Sub amp

10-28-2019, 09:33 AM	#22935
GearheadSS Drives: 23 LT1/86 IROC-Z Join Date: Jun 2006 Location: Greenville, Tx Posts: 5,044 View My Garage	New rotors and pads. OEM rotors with Powerstop Extreme Z26 pads. Attached Images

10-30-2019, 12:06 AM	#22936
15RS2NV Ponies are for girls Drives: 2015 RS LFX Red Hot A6 Join Date: Sep 2018 Location: Southern AZ Posts: 315 View My Garage	Ordered some toys: - Overkill 80mm Throttle Body - Accel ignition coils - Intake manifold spacer insulator (MACE) - Made an appointment to get intake manifold ported They start coming in Friday so she'll be in the garage for a week or two. __________________ H&R 1.8/1.7” drop, Overkill 80mm + intake ported by AFS, 1" insulator MACE, Accel Super Coils, THR cai, JET MAF sensor, Hurst shifter handle, GPP strut tower brace, CI ice cube tray hood vents (functional) @SemperFiCamaro

11-01-2019, 06:12 PM	#22937
Leo72793 Drives: 2011 2SS/RS Join Date: Feb 2016 Location: Jacksonville FL Posts: 1,227	Debating on either 2 10 boston acoustics 10.4LF old schools or s ingle Alpine 10 X series new 2019 sub __________________ •2011 Camaro SS 2SS/RS A6 •MRR M017 1le Replica Wheels •Vararam Ram Air Intake •Speed Engineering Longtube Headers w/ Magnaflow HF Cats •Bo White PnP Stage 2 TB •GPI SS2 VVT Cam w Cometic thin gaskets 10.69 compression •Xpipe w/ Res Delete and NPP Exhaust •Tuned By Anonymous Calibrations •Gen5DIY Mylink Conversion W/ Backup Cam •Morel 3 way custom speakers, Infinity 860w Subwoofers in trunk baffle •Helix P6 6ch amp w/ 8ch DSP and P1 Sub amp

11-01-2019, 09:02 PM	#22938
Spec Account Suspended Drives: 2010 Camaro 1SS LS3 Join Date: Jan 2015 Location: Riverside, CA Posts: 4,018	Got it fixed! Can't wait to have some fun again with my ride this weekend!! First a nice thorough wash! Then, the sky's the limit. Attached Images

11-04-2019, 03:00 PM	#22943
SS_CTS-V Drives: 2015 SS, 2006 CTS-V (wrecked...) Join Date: Jul 2017 Location: Tampa Posts: 151	Just a little vinyl work on Sunday afternoon. Not my design, but I did have to tweak it a bit to fit the window as well as flip everything for the other side. Nothing special, just a Cricut machine and some basic graphics work.

11-04-2019, 03:16 PM	#22944
redcoats1976 Drives: LT W/2LT,blue metallic Join Date: Jul 2016 Location: central florida Posts: 5,032	good to see you back on the road and out of the dumps spec.all i did to mine was fix a few paint chips today.next monday its gotta go to the dealer,engine light is on.something in the emissions system is gone bad...

11-07-2019, 11:14 PM	#22946
15RS2NV Ponies are for girls Drives: 2015 RS LFX Red Hot A6 Join Date: Sep 2018 Location: Southern AZ Posts: 315 View My Garage	Well, this is more of a "what have i done with your Camaro this week". I ordered and received the Overkill 80mm throttle body, MACE Engineering 1" intake manifold insulator (spacer), and had them and the intake manifold sent out to have the intake manifold fully ported and matched to the TB and the insulators to all match the manifold and engine. Not being happy sitting around waiting, I'm sanding the camshaft covers (where valve covers are on V8s) and polishing. Not leaving well enough alone, I'm not sanding and polishing the water pump and brackets along the front of the engine. __________________ H&R 1.8/1.7” drop, Overkill 80mm + intake ported by AFS, 1" insulator MACE, Accel Super Coils, THR cai, JET MAF sensor, Hurst shifter handle, GPP strut tower brace, CI ice cube tray hood vents (functional) @SemperFiCamaro

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GM memo to dealers	Moose	5th Gen Camaro SS LS LT General Discussions	41	02-04-2010 08:33 PM
Major Pedders Event in Houston! Saturday, Jan 30th! Meet DMS	Info@PeddersUSA.com	USA - Texas	39	02-01-2010 01:48 PM
Answeres to questions I have stumbled on	dieseldave24v	5th Gen Camaro SS LS LT General Discussions	13	02-23-2009 07:56 PM