EOM Retrofit Morimoto HID (possibly LED)

[rsrsrs]

Originally Posted by Leo72793

shouldnt be too hard. it appears to be the same size as the ring on the D1S. Remember too, you can put the cable in on the outside of the headlight or once in.

Removing the adapter from the headlight isn't an issue, it's the other end, believe it's the ballast(?). I think it's clipped in. I just wasn't able to get at it. If I remember correctly it's right up against a plastic wall. Figured all I needed to do was remove the 4 screws holding the piece in but it's blocked by something else under it. I know a picture would be show what I mean. Maybe I'll try doing that later.

[rsrsrs]

Originally Posted by rsrsrs

Removing the adapter from the headlight isn't an issue, it's the other end, believe it's the ballast(?). I think it's clipped in. I just wasn't able to get at it. If I remember correctly it's right up against a plastic wall. Figured all I needed to do was remove the 4 screws holding the piece in but it's blocked by something else under it. I know a picture would be show what I mean. Maybe I'll try doing that later.

Okay, got pics. So in one pic we'll see the adapter butted right up against the wall. Maybe there's a way to take it off but I didn't want to risk it. So like I said I wanted to remove the piece. The other pic is showing the small space there is between that ballast (?) and the body.

[Leo72793]

Originally Posted by rsrsrs

Okay, got pics. So in one pic we'll see the adapter butted right up against the wall. Maybe there's a way to take it off but I didn't want to risk it. So like I said I wanted to remove the piece. The other pic is showing the small space there is between that ballast (?) and the body.

the mentioned parts would only affect inside the headlight and reuse the OEM ballast (bottom picture) and igniter wire. The adaptor takes the D1S plug inside the light to the D2S connector.

[SummitWhite11]

Originally Posted by Leo72793

NOT 100% but i believe this is what we will be using:

Theres a few parts we will need:

Projectors (upgrading our stocks):
https://www.morimotohid.com/bi-xenon...s_3?quantity=1

D2S bulbs (because D1S fit differently)
https://www.morimotohid.com/morimoto...lbs?quantity=1

D2S to D1S Adaptors (to reuse OEM ballasts and wiring):
https://www.morimotohid.com/morimoto...s_2?quantity=1

After looking at the first link it is not clear we will need any of the other “optional” components from each of the drop down menu fields. Can you confirm?


Sent from my iPhone using Tapatalk

[Leo72793]

Originally Posted by SummitWhite11

After looking at the first link it is not clear we will need any of the other “optional” components from each of the drop down menu fields. Can you confirm?


Sent from my iPhone using Tapatalk

We shouldnt need any of them since we are using the bracket to mount not the lock ring, the shroud is a cover for around the lense which we wont use (oem area covers it) and the other part we shouldnt need either.

[SaReNi]

Originally Posted by Leo72793

Don't fret. I'll handle it

no worries. thanks.

[SummitWhite11]

Originally Posted by Leo72793

We shouldnt need any of them since we are using the bracket to mount not the lock ring, the shroud is a cover for around the lense which we wont use (oem area covers it) and the other part we shouldnt need either.

Good to know. Did they mention a turn around time for when these would be produced and shipped once we met their group buy requirements?

[Leo72793]

Originally Posted by SummitWhite11

Good to know. Did they mention a turn around time for when these would be produced and shipped once we met their group buy requirements?

As of now no. RnD may take a few weeks but I'll keep everyone updated best possible.

[SummitWhite11]

Originally Posted by Leo72793

As of now no. RnD may take a few weeks but I'll keep everyone updated best possible.

Sent from my iPhone using Tapatalk

[rsrsrs]

Originally Posted by Leo72793

the mentioned parts would only affect inside the headlight and reuse the OEM ballast (bottom picture) and igniter wire. The adaptor takes the D1S plug inside the light to the D2S connector.

Oooooh okay okay. Great.

[Leo72793]

Update: prototypes are being developed. Possibly fitting a 3" as well. That will require the lights be opened but we shall see!

[camguynj]

Originally Posted by Leo72793

Update: prototypes are being developed. Possibly fitting a 3" as well. That will require the lights be opened but we shall see!

Does this mean all the invoices have now been paid?

[Leo72793]

Originally Posted by camguynj

Does this mean all the invoices have now been paid?

From my understanding yes. This may also be a NO BAKE options too. 3" would require baking but we are exploring the option for those who want 3"

[Leo72793]

Those who over payed should have credits by now, i have seen the prototype and it looks VERY promising to be a no bake option!