What Did You Do To Your Camaro Today? [v2 thread] - Page 46 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Infidel67 · 11-05-2023, 07:42 AM

Quote:

Originally Posted by SlowLS1

Ole gal has been put to bed for the winter, ready to be put on the lifts and have tranny pulled out. Pig Mat on the floor for any spills. Don't want to mess up my new flooring

Gosh Bro is that Baby that Low

and btw nice Undies

1JEWLDSSRS · 11-05-2023, 09:43 AM

Quote:

Originally Posted by ariZona28

I went with the regular wet battery, since that's what was in there. Not cheap at $190 but gotta have volts and amps to start.
The Z trunk is bare bones, no mat or carpet but the car has less than 7000 miles so maybe that's why the trunk is so clean. LOL!

Cool, thanks. Yeah I've had 2 wet batteries puke already in my trunk in the past 4 years, so I'm going with the AGM this time. Just haven't bought it yet. 254 bucks for the Diehard one. They have the best reviews over the Duralast.

1JEWLDSSRS · 11-05-2023, 09:46 AM

Quote:

Originally Posted by SlowLS1

Ole gal has been put to bed for the winter, ready to be put on the lifts and have tranny pulled out. Pig Mat on the floor for any spills. Don't want to mess up my new flooring

Here ya go sir, I flipped your pic for you.

Name: IMG-0646.jpg
Views: 209
Size: 206.9 KB

SlowLS1 · 11-05-2023, 10:03 AM

Quote:

Originally Posted by 1JEWLDSSRS

Here ya go sir, I flipped your pic for you.

Attachment 1140028

Appreciate it sir! No matter what way I flipped it, always uploaded the same. I gave up lol.

SlowLS1 · 11-05-2023, 10:06 AM

Quote:

Originally Posted by Detleg

Gosh Bro is that Baby that Low

and btw nice Undies

That’s the nice thing about being on air. Can be as low or as high as the situation requires. As for the undies, can’t go wrong with pig mat.

1JEWLDSSRS · 11-05-2023, 10:13 AM

Quote:

Originally Posted by SlowLS1

Appreciate it sir! No matter what way I flipped it, always uploaded the same. I gave up lol.

No worries sir!! My pleasure..

SlowLS1 · 11-05-2023, 12:11 PM

She is ready for some major surgery. Gonna be a while before she moves again.

1JEWLDSSRS · 11-05-2023, 01:05 PM

Quote:

Originally Posted by SlowLS1

She is ready for some major surgery. Gonna be a while before she moves again.

Awesome! Have fun, be careful and enjoy!!

SlowLS1 · 11-05-2023, 01:34 PM

Quote:

Originally Posted by 1JEWLDSSRS

Awesome! Have fun, be careful and enjoy!!

Got exhaust out, prop shaft out, shifter disconnected, cussed the person who thought it would be funny if the connection in the o2 sensors wouldn’t let you reach the connector well, and got kroil on the studs for the cats.

Trying to have fun, but I forgot that I’m too old to enjoy crawling around on the floor. I also realize I need all my tools on the wall to actually be under the car since I’ve got no one to fetch tools. lol

Need to find me a good toolbag to keep under the car with me.

1JEWLDSSRS · 11-05-2023, 07:40 PM

Quote:

Originally Posted by SlowLS1

Got exhaust out, prop shaft out, shifter disconnected, cussed the person who thought it would be funny if the connection in the o2 sensors wouldn’t let you reach the connector well, and got kroil on the studs for the cats.

Trying to have fun, but I forgot that I’m too old to enjoy crawling around on the floor. I also realize I need all my tools on the wall to actually be under the car since I’ve got no one to fetch tools. lol

Need to find me a good toolbag to keep under the car with me.

lol. I hear ya on that one!! But at least you got a good start on it. Just be careful!! I also love how you used "protection", lol, on the front end. We did the same when we did my cam swap. Cheers my brother!!

George-CZ · 11-06-2023, 03:17 PM

After two months of waiting for a custom driveshaft finally the first ride with the Tetemec TKX after replacing it with a TH350.

A car from another world!

Name: 20231102_112826.jpg
Views: 191
Size: 222.1 KB

Name: 20231102_112826.jpg
Views: 191
Size: 222.1 KB

Name: 20231103_151730_HDR.jpg
Views: 172
Size: 122.1 KB

Name: 20230802_101812.jpg
Views: 182
Size: 191.8 KB

Infidel67 · 11-06-2023, 03:37 PM

Quote:

Originally Posted by SlowLS1

She is ready for some major surgery. Gonna be a while before she moves again.

I need to come by one weekend and check out what you got cooking

Infidel67 · 11-06-2023, 06:56 PM

Got an Alignment done today, wasn't off that bad beside rear driver side.
Did a rear Bow Tie Delete

Greased all fitting besides rear sway bar, I will change out the fittings to a either 45 or 90 degree elbow one, should have done it before but didn't have the correct grease. Started to paint the front SS emblem , all I got left is fill the inside with black, probably using a syringe for it, don't know yet.
My Center Brace sits perfect

1JEWLDSSRS · 11-07-2023, 07:46 PM

Quote:

Originally Posted by George-CZ

After two months of waiting for a custom driveshaft finally the first ride with the Tetemec TKX after replacing it with a TH350.

A car from another world!

Attachment 1140096

Attachment 1140097

Attachment 1140098

Very nice George!!

11-05-2023, 12:11 PM	#637
SlowLS1 Drives: 2010 Camaro SS , 2011 Colorado LS1 Join Date: Jan 2022 Location: Greenville, SC Posts: 1,217	She is ready for some major surgery. Gonna be a while before she moves again. Attached Images __________________

11-06-2023, 03:17 PM	#641
George-CZ Drives: 2010 2SS LS3 and 1978 STROKER 383 Join Date: Feb 2018 Location: Czech Republic Posts: 1,611	After two months of waiting for a custom driveshaft finally the first ride with the Tetemec TKX after replacing it with a TH350. A car from another world! __________________ My life is a constant struggle with Camaro. K&N CAI, Stainless Power longtubes, high flow cats, modified Ragazzon High Performance axle back, Soler Performance ported throttle body, Soler Performance throttle controller, RAM clutch adjuster, modified LS7 clutch kit, Tick Performance billet bearing support, Tick Performance remote bleeder, separate clutch reservoir, BMR trailing arms, BMR toe rods, Pedders Suspension cradle bushing inserts, Control Arm Bushings, Strut tower brace, oil catch can, Hurst T-handle shifter, 20mm wheel spacers, DBA brakes, QTP Cutouts, Dynosteve tune.

11-06-2023, 06:56 PM	#643
Infidel67 Life's just a Ride Drives: 2011 Synergy Camaro 2SS/RS LS3 Join Date: Oct 2013 Location: Columbia SC Posts: 885 View My Garage	Got an Alignment done today, wasn't off that bad beside rear driver side. Did a rear Bow Tie Delete Greased all fitting besides rear sway bar, I will change out the fittings to a either 45 or 90 degree elbow one, should have done it before but didn't have the correct grease. Started to paint the front SS emblem , all I got left is fill the inside with black, probably using a syringe for it, don't know yet. My Center Brace sits perfect Attached Images __________________ 2011 Synergy Camaro 2SS/RS Ls3, LTH, CAI Custom Intake, TSP stage-3 111-LSA Cam, RWHP 503/508