What Did You Do To Your Camaro Today? [v2 thread] - Page 80 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

2010sgm · 04-30-2024, 08:51 PM

Quote:

Originally Posted by 1JEWLDSSRS

Brother man, boy she is looking better and better each time you post!! Love the look! Also in looking at your front bumper cover in the center where it touches the bottom of the grille, either the cover isn't installed all the way, or it's sagging, or the bottom of the grille isn't pulled all the way out to meet the top of the cover, because I can see the notches in the cover, or the bottom of the grille.. But otherwise, looks great!!

humm i Tried pulling it in with no luck not really wanting to take cover off again...ugh...

chevy pilot · 04-30-2024, 10:43 PM

Quote:

Originally Posted by 2010sgm

heritage grill on my 2010 synergy

Looks even better.

trashbasket · 05-01-2024, 07:11 AM

Quote:

Originally Posted by 2010sgm

humm i Tried pulling it in with no luck not really wanting to take cover off again...ugh...

I had to transfer same grill between bumpers and its not fun, but yea yours aint in all the way. Its absolutely a pain. A real fun thing is getting it put on all the way and then having it pushed back out over 120mph. I had to install these shark teeth clips on the back of those tabs to stop that from happening. Good luck with it. Car looks great otherwise.

1JEWLDSSRS · 05-01-2024, 08:42 AM

Quote:

Originally Posted by 2010sgm

humm i Tried pulling it in with no luck not really wanting to take cover off again...ugh...

Yeah, it is quite the PITA!!! Hope you can get it adjusted. Car looks great.

ariZona28 · 05-03-2024, 03:25 AM

Late night oil change. Weather was nice, I had all of the stuff so I said WTF, might as well get something accomplished.

Jeff_SS · 05-03-2024, 06:17 PM

Quote:

Originally Posted by ariZona28

Late night oil change. Weather was nice, I had all of the stuff so I said WTF, might as well get something accomplished.

I did the same thing the other night. Fairly enjoyable outside when it's 9pm or later here right now.
Only drawback is starting the car and pulling back into the garage late at night which my neighbors likely don't enjoy as much as I do.

NoDakZ/28 · 05-06-2024, 07:58 AM

Got the 2" ARH longtubes with high flow cats, 3" stainless exhaust with x-pipe to the factory npp mufflers done this weekend. Sounds great, just have to finish my ported TB and get a nice tune done, can't wait!
Name: 88A7F03B-F2C5-4CBB-88F8-3B2B8C7C7E6C.jpg
Views: 366
Size: 148.4 KB

Name: 88A7F03B-F2C5-4CBB-88F8-3B2B8C7C7E6C.jpg
Views: 366
Size: 148.4 KB

Name: A74165DC-20B2-4CED-9E66-E5B4FE36FBD8.JPG
Views: 384
Size: 128.3 KB

Name: IMG_0745.jpg
Views: 370
Size: 156.0 KB

Unaf-Ford-able · 05-06-2024, 11:19 AM

I stared at the chipped windshield that I'm going to have to replace after a local firetruck kicked up a rock and launched it at me.

Odd, I thought that everyone had to follow the "must have mudflaps" rule.

The_bald_eagle_machine · 05-06-2024, 11:22 AM

Quote:

Originally Posted by Unaf-Ford-able

I stared at the chipped windshield that I'm going to have to replace after a local firetruck kicked up a rock and launched it at me.

Odd, I thought that everyone had to follow the "must have mudflaps" rule.

I bet if you have a dashcam video of the incident, you could get the county to pay for it. Otherwise its your word against them and chances are you will lose and look like an a** in the process.

That sucks though... do you also need a blend door replacement? Would be a great time to do it if you do. I'm a glass half full type of guy though.

The_bald_eagle_machine · 05-06-2024, 11:23 AM

Quote:

Originally Posted by NoDakZ/28

Got the 2" ARH longtubes with high flow cats, 3" stainless exhaust with x-pipe to the factory npp mufflers done this weekend. Sounds great, just have to finish my ported TB and get a nice tune done, can't wait!
Attachment 1150970
Attachment 1150971
Attachment 1150972

Man... I'd love to hear that thing sing its song.

Blue 13 · 05-06-2024, 11:30 AM

Awesome NoDak!!!!!

NoDakZ/28 · 05-06-2024, 11:50 AM

Quote:

Originally Posted by The_bald_eagle_machine

Man... I'd love to hear that thing sing its song.

Quote:

Originally Posted by Blue 13

Awesome NoDak!!!!!

Thank you, I will try and get a sound clip. Its nice and throaty at idle, and really wakes up past 4k rpms!

InFiD3ViL · 05-06-2024, 09:16 PM

Removed my hood wrap....after 6 years (yeah, I know). Made sure to use a heat gun, but still left staining from the glue. Now I have to figure out how the heck to get the glue stains/remnants off the finish. You can barely feel the glue, but you can see it in certain light.

When I bring the car to get the ZL1 front bumper paint quote, I am also going to inquire about an entire front clip respray. And yes, I am aware that I have excessive gap between hood and front bumper cover. That will be addressed with the new bumper.

chevy pilot · 05-07-2024, 04:13 AM

Glue possibly with this substance carefully.
Maybe you have to polish lightly

05-03-2024, 03:25 AM	#1111
ariZona28 Give speed a chance Drives: 2015 Camaro 2LS, 2015 Camaro Z/28 Join Date: Nov 2019 Location: Mesa, Az Posts: 2,830	Late night oil change. Weather was nice, I had all of the stuff so I said WTF, might as well get something accomplished. Attached Images __________________ 2LS: a TREMENDOUS machine. Z/28: it's a BIT MORE POWERFUL, of course.

05-06-2024, 07:58 AM	#1113
NoDakZ/28 Drives: 2014 Z/28 CTF Join Date: Sep 2017 Location: North Dakota Posts: 692 View My Garage	Got the 2" ARH longtubes with high flow cats, 3" stainless exhaust with x-pipe to the factory npp mufflers done this weekend. Sounds great, just have to finish my ported TB and get a nice tune done, can't wait! __________________ 2014 1LE - Sold 2014 Z/28 #99008 CTF SIM

05-06-2024, 11:30 AM	#1117
Blue 13 3P171 USAF Combat Arms Drives: 2013 SS/RS Join Date: Jul 2021 Location: Olmsted AFB Posts: 416	Awesome NoDak!!!!! __________________ 416ci LS3/Vortech V7/Built 6L80 996.6 RWHP 794.9 RWTQ

05-06-2024, 09:16 PM	#1119
InFiD3ViL Drives: 2010 CGM 2SS/RS LS3 Swapped A6 Join Date: Sep 2016 Location: Spring Hill, FL Posts: 4,737	Removed my hood wrap....after 6 years (yeah, I know). Made sure to use a heat gun, but still left staining from the glue. Now I have to figure out how the heck to get the glue stains/remnants off the finish. You can barely feel the glue, but you can see it in certain light. When I bring the car to get the ZL1 front bumper paint quote, I am also going to inquire about an entire front clip respray. And yes, I am aware that I have excessive gap between hood and front bumper cover. That will be addressed with the new bumper. Attached Images __________________ 2010 CGM Camaro 2SS LS3 Swapped A6 - GPI LS3 SS1 .647/.638, (224/237, 112 +4, 7º overlap) on CamMotion 8620 core, BTR Platinum .660" Dual Spring kit w/titanium retainers, CHE bronze trunnion upgrade, stock heads milled @ .015, Melling HV 10296 oil pump, TSP 1-7/8" long tube headers (W/Catless Off-road Pipes), Corsa Xtreme 3" Catback, GPI Ported/Rod Mod Intake, Stage 2 Ported Throttle Body, Vararam OTR CAI, Mike Norris Gen 2 catch can + GM 1LE clean side separator, 160º thermostat - Megan Racing adjustable coilovers (lowered 1.75"), MRR M017 10/11" wheels-Tuned by Ryan @ GPI

05-07-2024, 04:13 AM	#1120
chevy pilot Drives: 2010 2SS/RS A6 Join Date: May 2019 Location: Hki.Finland Posts: 1,323	Glue possibly with this substance carefully. Maybe you have to polish lightly Attached Images

05-06-2024, 11:19 AM	#1114
Unaf-Ford-able Drives: 2010 Synergy Camaro Join Date: Apr 2023 Location: Oregon, the State Park! Posts: 69	I stared at the chipped windshield that I'm going to have to replace after a local firetruck kicked up a rock and launched it at me. Odd, I thought that everyone had to follow the "must have mudflaps" rule.