BCM wiring - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

HaZe_X · 11-29-2009, 02:49 PM

So I got to thinking, I saw a couple of DIY's about killing the DRL's, and having fogs come on at night, and all these guides are not using the BCM wiring.

Now I know on my Trailblazer SS we can splice 2-3 wires, and add a relay to the BCM to kill the DRL's, or kill the auto lights, or even have High+lows on at the same time.

Wouldn't it be a simpler solution for the camaro to do this all in the BCM wiring rather then go to the headlights? Im sure all those functions are controlled by the BCM, and I have the wiring diagram for my 07 TBSS, cant be to far off from the new camaros.

If anyone has a the BCM wiring diagram, post it up..

HeavyD · 11-30-2009, 09:10 AM

I wouldn't mind some more wire diagrams too.

slick rick · 11-30-2009, 11:32 AM

http://www.camaro5.com/forums/showthread.php?t=24704

http://www.camaro5.com/forums/showthread.php?t=33592

?

HeavyD · 12-01-2009, 11:44 AM

I'd like to see ignition feed circuits and BC inputs and outputs.

ABB · 11-03-2012, 06:57 PM

Quote:

Originally Posted by HaZe_X

So I got to thinking, I saw a couple of DIY's about killing the DRL's, and having fogs come on at night, and all these guides are not using the BCM wiring.

Now I know on my Trailblazer SS we can splice 2-3 wires, and add a relay to the BCM to kill the DRL's, or kill the auto lights, or even have High+lows on at the same time.

Wouldn't it be a simpler solution for the camaro to do this all in the BCM wiring rather then go to the headlights? Im sure all those functions are controlled by the BCM, and I have the wiring diagram for my 07 TBSS, cant be to far off from the new camaros.

If anyone has a the BCM wiring diagram, post it up..

Below are some, hope it helps

Slip n Slide MN · 09-26-2019, 12:28 PM

I understand this is a very old thread, but I have a question and hopefully someone can give an answer... I have replaced my Halo lights with red LED rings 'demon eyes'. I love them and have used them for years. But recently I have needed to disconnect them because the police do not like red lights on the front of a civilian car.

I have found the +12 wire for each LED ring at the BCM right above the gas pedal.
My Question is, can I bridge these into one SPST switch to manually interrupt them? Or should I get a DPST switch to keep the two channels separate?
The two wires do not have continuity when switched on. But I don't know if it would hurt the BCM to bridge the two +12 wires.

Thank you for any help/advice/thoughts on this... :-)

11-29-2009, 02:49 PM	#1
HaZe_X Drives: Trailblazer SS & Camaro SS Join Date: Nov 2009 Location: North Jersey Posts: 758	BCM wiring So I got to thinking, I saw a couple of DIY's about killing the DRL's, and having fogs come on at night, and all these guides are not using the BCM wiring. Now I know on my Trailblazer SS we can splice 2-3 wires, and add a relay to the BCM to kill the DRL's, or kill the auto lights, or even have High+lows on at the same time. Wouldn't it be a simpler solution for the camaro to do this all in the BCM wiring rather then go to the headlights? Im sure all those functions are controlled by the BCM, and I have the wiring diagram for my 07 TBSS, cant be to far off from the new camaros. If anyone has a the BCM wiring diagram, post it up..

11-30-2009, 11:32 AM	#3
slick rick SoCal Mayhem Drives: 2010 Camaro 1SS/RS Join Date: Aug 2008 Location: Foothill Ranch, CA Posts: 5,488 View My Garage	http://www.camaro5.com/forums/showthread.php?t=24704 http://www.camaro5.com/forums/showthread.php?t=33592 ? __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wiring in a KB Boost a pump	R8cerX	Forced Induction - V8	59	11-25-2019 05:34 PM
Garmin nuvi > mounting & wiring for the Camaro	67 GTO	Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum	25	11-05-2011 01:52 PM
Halos/HID on 2 LT wiring ?	lostinvt	Camaro DIY & HOW-TO instructions & discussions	2	12-29-2009 09:54 AM
Anyone have picts/info on the factory infotainment system wiring harness & plugs?	Matt'sSS	Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum	3	10-01-2009 01:48 AM

11-30-2009, 09:10 AM	#2
HeavyD Drives: 1SSRS RY L99 Join Date: Aug 2009 Location: Ontario Posts: 1,323	I wouldn't mind some more wire diagrams too.

12-01-2009, 11:44 AM	#4
HeavyD Drives: 1SSRS RY L99 Join Date: Aug 2009 Location: Ontario Posts: 1,323	I'd like to see ignition feed circuits and BC inputs and outputs.

09-26-2019, 12:28 PM	#6
Slip n Slide MN Drives: 2011 Camaro 2SS - RED Join Date: Sep 2019 Location: Minnesota Posts: 6	I understand this is a very old thread, but I have a question and hopefully someone can give an answer... I have replaced my Halo lights with red LED rings 'demon eyes'. I love them and have used them for years. But recently I have needed to disconnect them because the police do not like red lights on the front of a civilian car. I have found the +12 wire for each LED ring at the BCM right above the gas pedal. My Question is, can I bridge these into one SPST switch to manually interrupt them? Or should I get a DPST switch to keep the two channels separate? The two wires do not have continuity when switched on. But I don't know if it would hurt the BCM to bridge the two +12 wires. Thank you for any help/advice/thoughts on this... :-)