Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Phastek Performance
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons


Reply
 
Thread Tools
Old 08-07-2010, 09:23 AM   #1
Jekyll-N-Hyde
I put the FU back in FUN
 
Jekyll-N-Hyde's Avatar
 
Drives: 1969 SS 396 , 2010 Camaro SS
Join Date: Jun 2009
Location: Between Weatherford and Azle TX hway730
Posts: 2,129
Thanks Adm once gain for the 3200 Yank Install

Thanks once again Andy , pat and Rick

After the ls3 conversion and cam install to my a6 Camaro the car had me thinking she finally reached her potential however after a few days above 105 degrees and a few tweaks to the tune Andy advised me the car needed a stall since this stage 2 cam that we used was proabably a little stout on the exhaust end and for the Stock converter.

( Note this Cam is normally used on manual Cars )

Despite the BUSY Schedule Andy once again made the time and accepted my car and installed a Yank 3200 Torque converter in less than a day.

As I am still under the 150 mile break in period I have not seen what she can do however I can say the car runs like a champ and feels almost stock under normal driving situations. Despite the lope of the cam you wouldnt know its a modded car which is awsome. Even though I have not done anything yet with the car since the addition of the stall I can feel the Torque down low BIG TIME just driving normal out of the hole.

Something tells me im going to need lots of hours of practicing to get this car to hook up.
Pat I think I need a set of Rear Z06 wheels with Sticky rubber

Thank's guys for making this Conversion VERY enjoiable There is no Pull , Hesitation or any discomfort driving this car at all. she still needs a few weeks to relearn everything as in the tune and driving style however it all takes time.

I will probably give it a good 200 miles instead of 150 for the break in therefore I know the torque converter is not being abused early.




For any of you guys who want a good Bang for the Buck go with the ADM stage 2 cam and pair it with the ADM Race CAI it will give your butt dyno a rush for sure and your ears a tune that you will look forward to everytime you crank it over.

Back to the Roads

Now
Jekyll-N-Hyde is offline   Reply With Quote
Old 08-07-2010, 09:08 PM   #2
Jason 98 TA

 
Drives: Camaro
Join Date: Apr 2009
Location: Texas
Posts: 1,670
That's awesome you liked the yank, we just did a buy in with them and are planning on stocking them. I'll install my 3600 next week!!!
Jason 98 TA is offline   Reply With Quote
 
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
My ADM street intake review*long and informative* pictures to keep you entertained ackeight Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 40 12-29-2016 08:41 AM
ADM PERFORMANCE DOES CUSTOM AEROFORCE INTERCEPTOR INSTALL ON CAMARO ADM PERFORMANCE Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 50 08-06-2016 12:11 PM
DIY : Install Performance Swaybars in 2010 Camaro Nine Ball Camaro DIY & HOW-TO instructions & discussions 17 09-14-2015 12:36 AM
DIY : Install underdrive pulley on 2010 Camaro SS Nine Ball Camaro DIY & HOW-TO instructions & discussions 34 09-30-2013 08:25 PM


All times are GMT -5. The time now is 06:15 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.