RX Catch Can installed, love it!!! - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

nyrfan · 11-20-2011, 04:46 PM

I must say I love it!! Unfortunately I was sent the wrong brackets (unpainted) but Tracy is sending me the correct CGM ones (I ordered both brackets). I am in no way upset by the error, shit happens, no worries. Tracy addressed all my concerns (I probably drove him nuts) and seems like a great guy, no wonder everyone speaks so highly of him. I love my CC, here are some pics (buy RX):

Nmbr1gmfan · 11-20-2011, 05:25 PM

RX does make the best catchcan.

OOLIE · 11-20-2011, 05:41 PM

Quote:

Originally Posted by Nmbr1gmfan

RX does make the best catchcan.

+1 over 15,000 miles with mine and no drops of oil behind TB. Plenty before that though. I have had a lot of work done by Tracy and he has unbelievable customer service.

rtcat600man · 11-20-2011, 05:42 PM

Looks like a great setup. I too agree that Tracy will take care of any customer questions, concerns, comments, etc. He goes out of his way to satisfy his customers.

nyrfan · 11-20-2011, 06:09 PM

Quote:

Originally Posted by rtcat600man

Looks like a great setup. I too agree that Tracy will take care of any customer questions, concerns, comments, etc. He goes out of his way to satisfy his customers.

I have to say he really cares about his products/brand name! Class act!!

Cincy10SSRS · 11-21-2011, 12:19 PM

I'm not trying to be critical but those hoses coming out from under the engine cover look a little funky and big. Does the one always come out on top of the intake tube like that? I don't think my engine cover would seat/fit right if I had a hose on top of the intake tube like that with my K&N Typhoon.

nyrfan · 11-21-2011, 12:40 PM

Quote:

Originally Posted by Cincy11RS

I'm not trying to be critical but those hoses coming out from under the engine cover look a little funky and big. Does the one always come out on top of the intake tube like that? I don't think my engine cover would seat/fit right if I had a hose on top of the intake tube like that with my K&N Typhoon.

I agree with you, does look a bit out of place, but this was my fault. I tried to get to neat and cut the tubing too short, so I temporarily had to run it this way. Tracy is sending me some new tubing when he sends the brackets, both should be here tomorrow. Once I get the tubing it will be properly run to the side of the engine cover and out of the way.

I may even decide to move it to the drivers side, this would be the neatest option.

velociSSimo · 11-21-2011, 12:48 PM

Quote:

Originally Posted by Nmbr1gmfan

RX does make the best catchcan.

PLuche · 11-21-2011, 12:59 PM

How much does an RX catch can cost ... Im guessing its the same for all camaros? I have a 2012 V6

nyrfan · 11-21-2011, 01:02 PM

Quote:

Originally Posted by IrvingLudwig

How much does an RX catch can cost ... Im guessing its the same for all camaros? I have a 2012 V6

The RX catch can is $154 shipped, see below:

http://www.camaro5.com/forums/showthread.php?t=109416

Cincy10SSRS · 11-21-2011, 01:23 PM

Quote:

Originally Posted by nyrfan

I agree with you, does look a bit out of place, but this was my fault. I tried to get to neat and cut the tubing too short, so I temporarily had to run it this way. Tracy is sending me some new tubing when he sends the brackets, both should be here tomorrow. Once I get the tubing it will be properly run to the side of the engine cover and out of the way.

I may even decide to move it to the drivers side, this would be the neatest option.

Gotcha; thanks for the reply. I am seriously considering getting one of these also.

nyrfan · 11-21-2011, 01:34 PM

Quote:

Originally Posted by Cincy11RS

Gotcha; thanks for the reply. I am seriously considering getting one of these also.

If you do learn from my mistake. I tried to run it fully under the cover (like I said to neat), that cannot be done and I cut the hose to short. Measure your path 1st, then cut.

nyrfan · 11-22-2011, 10:13 AM

So I received the correct bracket from Tracy along with the extra hose I needed, the install is now complete. Here are some pics:

General pictures:

JoshBobGuptaMarley · 11-22-2011, 10:19 AM

Quote:

Originally Posted by IrvingLudwig

How much does an RX catch can cost ... Im guessing its the same for all camaros? I have a 2012 V6

I just installed mine on my 2012 v6. Looks great!

11-20-2011, 04:46 PM	#1
nyrfan Let's go Rangers! Drives: 13' AGM 2SS/RS L99 Join Date: Jun 2011 Location: Orlando, FL Posts: 10,742 View My Garage	RX Catch Can installed, love it!!! I must say I love it!! Unfortunately I was sent the wrong brackets (unpainted) but Tracy is sending me the correct CGM ones (I ordered both brackets). I am in no way upset by the error, shit happens, no worries. Tracy addressed all my concerns (I probably drove him nuts) and seems like a great guy, no wonder everyone speaks so highly of him. I love my CC, here are some pics (buy RX): __________________ Soprano 4/1/00-6/14/11, Gone but NEVER forgotten! FSP tuned: 377/389 Last edited by nyrfan; 11-21-2011 at 09:59 AM.

11-20-2011, 05:25 PM	#2
Nmbr1gmfan Drives: Fast Join Date: Feb 2010 Location: Sarasota, FL. Posts: 410	RX does make the best catchcan. __________________ http://www.youtube.com/watch?v=fPvVm...&feature=share New and improved non-violation sig vid!!

11-20-2011, 05:42 PM	#4
rtcat600man having FUN now 13.66@101 Drives: 2010 2LT IOM Join Date: Nov 2009 Location: Clarkston, Michigan Posts: 9,231 View My Garage	Looks like a great setup. I too agree that Tracy will take care of any customer questions, concerns, comments, etc. He goes out of his way to satisfy his customers. __________________ MY BUILD

11-22-2011, 10:13 AM	#13
nyrfan Let's go Rangers! Drives: 13' AGM 2SS/RS L99 Join Date: Jun 2011 Location: Orlando, FL Posts: 10,742 View My Garage	So I received the correct bracket from Tracy along with the extra hose I needed, the install is now complete. Here are some pics: General pictures: __________________ Soprano 4/1/00-6/14/11, Gone but NEVER forgotten! FSP tuned: 377/389 Last edited by nyrfan; 11-22-2011 at 01:33 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Installed my catch can - L99	SSGUNNER	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	0	11-11-2011 04:30 PM
Elite Engineering Catch Cans Now Available At APEX Motorsports! Multiple Colors!	Apex Motorsports	V8 Bolt-Ons & Tunes	136	06-30-2011 05:24 AM
RX Catch Can with breather installed!	95RedCamaroz28	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	42	02-03-2011 06:27 PM
RX Catch Can installed with pics!	ssmike	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	11	01-08-2011 08:05 PM
Dumbest Camaro5 Question EVER!	Beemer	5th Gen Camaro SS LS LT General Discussions	209	05-23-2010 06:11 PM

11-21-2011, 12:19 PM	#6
Cincy10SSRS Drives: 2010 2SS RS M6 Join Date: Mar 2011 Location: Cincinnati area Posts: 1,522	I'm not trying to be critical but those hoses coming out from under the engine cover look a little funky and big. Does the one always come out on top of the intake tube like that? I don't think my engine cover would seat/fit right if I had a hose on top of the intake tube like that with my K&N Typhoon.

11-21-2011, 12:59 PM	#9
PLuche Drives: 2012 Camaro 1LT manual Join Date: Aug 2011 Location: GA Posts: 489	How much does an RX catch can cost ... Im guessing its the same for all camaros? I have a 2012 V6