What mods are you doing this winter? (part II) - Page 3 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

KirkB · 11-30-2011, 09:13 AM

Will be doing
- taillight, side marker, headlight tint
- lowering springs
- CIA
- MRT 2 exhaust
- dark grey hood spears
- dark grey side vents
- stereo and speaker upgrade in wife's avalanche (required to do all the above)

May do
- engine cover air brushing
- throttle body spacer
- window tint
- black out silver trim rings in dash

all on my new black 2012 1LS with dark grey rial 18" rims. Just completed debadging, black tail light trim and C&C stereo upgrade. Can't wait to complete it all!!!

SSawdusty · 11-30-2011, 10:13 AM

Sounds good Shayne. I'll will get in touch with them. Enjoy the sun.

Quote:

Originally Posted by BUMBLE-B-TUNA

We will definately get together next summer, I was just so friggin busy with the house and yard. I'm in Phoenix for the winter, without my car this time

so I'll be in touch in the spring.

Malcolm at Harbour City is a good guy and so are the techs, Dave installed my gears. The only problem I had was with the LPW cover vent leak and it took a bit to find but they stuck with me, which says alot. The fact that they did mine with caps and posi mod should make it easier for you. It is pricey but they do it right.

They did come up with a fix for the LPW as well, they put an expandable bellows on the vent so I can now go 4x4ing lol.

Cheers, Shayne

ps: If you have any questions about anything let me know.

[/QUOTE]

Camaro21 · 11-30-2011, 10:17 AM

I will be getting my NOS Kit installed Monday at ADM Performance. I also have Pfadt Solid Subframe bushings on the way. I also have a Driveshaft Safety Loop to install. I can't wait until Spring arrives and brings some good weather !!

lakersftbl69 · 11-30-2011, 10:21 AM

Hurst short throw ordered already
Couple more days will be ordering a catch can
In the spring when I take it out again it'll be getting cammed

christcringle · 12-01-2011, 10:13 PM

Start my project

calbert1999 · 12-01-2011, 11:03 PM

Scrap that thing and get one of these.

christcringle · 12-03-2011, 02:17 PM

When finish anytime dude

Burnt_RS · 12-17-2011, 06:27 PM

No plans to spend any money. NOT A CENT

With that said, so far...

-spoke with SPi about springs/swaybars and line lock install in the spring
-have a set of interior and trunk red LEDs and footwell ambient lighting in red, coming from AAC.

As far as not spending money, I'm off to a bad start. No plans to do anything else, but you see how that's going already

2L82RUN · 12-17-2011, 07:27 PM

SUSPENSION MODS!!!

Pfadt:
Rear trailing arms
Rear toe rods
Solid subframe bushings
Differential bushings
Upgraded sway bar end links

Driveshaft Shop:
Level 5 1400 axles
Carbon Fiber driveshaft

Oh....and TIRES!!!!

calbert1999 · 12-18-2011, 12:45 PM

Just added Aerofoce gauges, pillar pod and shift light. ACT 1150 clutch finally arriving next week.

LIM3 · 12-18-2011, 12:55 PM

Throttle body
Reverse hood
Tints
And god knows what else

69 Rebel · 12-18-2011, 02:55 PM

Just when i though i was done, i come across the Unrestricted Motorsports Comp Series Extractor Hood.

stratman2SSRS · 12-18-2011, 07:13 PM

Quote:

Originally Posted by calbert1999

Just added Aerofoce gauges, pillar pod and shift light. ACT 1150 clutch finally arriving next week.

The aeroforce guages have a shift light built into them. Just in case you didn't know.

tpower · 12-18-2011, 07:18 PM

I traded my SS in for a ZL1 big mod

11-30-2011, 10:21 AM	#32
lakersftbl69 Drives: 2010 camaro ss Join Date: Mar 2009 Location: conway sc. Posts: 1,453 View My Garage	Hurst short throw ordered already Couple more days will be ordering a catch can In the spring when I take it out again it'll be getting cammed __________________ ordered dec 15 2008 picked up on june 8 2009. upgrades kooks 1 7/8" LTH w/ deleted cats, corsa exhaust, hurst short throw shifter stage 3 comp cam, 3.91 gears ecs kit blower, meth injection, upgraded axles, drive shaft, McLeod rxt clutch, fully forged 416ci stroker all installed and dyno tuned by slowhawk performance in bridgewater ma.

12-01-2011, 10:13 PM	#33
christcringle Drives: 2010 2SS/2011 Pacecar/2011 LS/ZL1 Join Date: Jul 2009 Location: Mtl,Qc,Canada Posts: 820	Start my project Attached Images __________________ Member ¨'' Club Elite '' #99

12-01-2011, 11:03 PM	#34
calbert1999 Camaro SS Lover Drives: 2010 Camaro 2SS/RS Black IOM Join Date: Jun 2010 Location: Toronto, Ontario (Canada) Posts: 2,862	Scrap that thing and get one of these. Attached Images

12-03-2011, 02:17 PM	#35
christcringle Drives: 2010 2SS/2011 Pacecar/2011 LS/ZL1 Join Date: Jul 2009 Location: Mtl,Qc,Canada Posts: 820	When finish anytime dude __________________ Member ¨'' Club Elite '' #99

12-17-2011, 06:27 PM	#36
Burnt_RS Drives: '10 1LT/RS Join Date: Apr 2010 Location: Canada Posts: 610	No plans to spend any money. NOT A CENT With that said, so far... -spoke with SPi about springs/swaybars and line lock install in the spring -have a set of interior and trunk red LEDs and footwell ambient lighting in red, coming from AAC. As far as not spending money, I'm off to a bad start. No plans to do anything else, but you see how that's going already Last edited by Burnt_RS; 12-18-2011 at 09:47 AM.

11-30-2011, 09:13 AM	#29
KirkB Don't Believe the Truth Drives: 2012 Chevy Camaro 1LS Join Date: Oct 2011 Location: Avondale, AZ Posts: 57	Will be doing - taillight, side marker, headlight tint - lowering springs - CIA - MRT 2 exhaust - dark grey hood spears - dark grey side vents - stereo and speaker upgrade in wife's avalanche (required to do all the above) May do - engine cover air brushing - throttle body spacer - window tint - black out silver trim rings in dash all on my new black 2012 1LS with dark grey rial 18" rims. Just completed debadging, black tail light trim and C&C stereo upgrade. Can't wait to complete it all!!!

11-30-2011, 10:17 AM	#31
Camaro21 Drives: SOLD - 2013 M6 ZL1 Join Date: Jul 2009 Location: Texas Posts: 5,040 View My Garage	I will be getting my NOS Kit installed Monday at ADM Performance. I also have Pfadt Solid Subframe bushings on the way. I also have a Driveshaft Safety Loop to install. I can't wait until Spring arrives and brings some good weather !!

12-17-2011, 07:27 PM	#37
2L82RUN Drives: ABM SS/RS Join Date: Sep 2009 Location: WV Posts: 587	SUSPENSION MODS!!! Pfadt: Rear trailing arms Rear toe rods Solid subframe bushings Differential bushings Upgraded sway bar end links Driveshaft Shop: Level 5 1400 axles Carbon Fiber driveshaft Oh....and TIRES!!!!

12-18-2011, 12:45 PM	#38
calbert1999 Camaro SS Lover Drives: 2010 Camaro 2SS/RS Black IOM Join Date: Jun 2010 Location: Toronto, Ontario (Canada) Posts: 2,862	Just added Aerofoce gauges, pillar pod and shift light. ACT 1150 clutch finally arriving next week.

12-18-2011, 12:55 PM	#39
LIM3 it's mind bottling.. Drives: SGM Join Date: Apr 2011 Location: miami floirda. Posts: 5,392	Throttle body Reverse hood Tints And god knows what else __________________

12-18-2011, 02:55 PM	#40
69 Rebel Drives: 2010 IBM 2SS/RS Auto Join Date: Apr 2010 Location: Laval, Canada Posts: 1,542	Just when i though i was done, i come across the Unrestricted Motorsports Comp Series Extractor Hood. __________________ Version I Jannetty Racing 550 RWHP Street Brawler Package, Powered by TVS2300 Maggie http://www.camaro5.com/forums/showthread.php?t=100385 Version II 416ci stroker/4L80e 701rwhp 750rwtq build and tuned by SPI-Performance

12-18-2011, 07:18 PM	#42
tpower DBLCHBY III Drives: 15 1LE Join Date: Jun 2011 Location: Team Canada Posts: 2,789	I traded my SS in for a ZL1 big mod __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My First Winter Mods..Elite..ADM..Roto-Fab	SSawdusty	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	9	02-10-2011 02:08 AM
Mods For Sale Part II	PonyMan	V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment	27	05-09-2010 01:21 AM
Scrming's Air Intake Experiment - Part II	scrming	Camaro V6 LLT Engine, Exhaust, and Bolt-Ons	94	05-02-2010 04:56 AM
DSV Customs Real Carbon Fiber 4 Gauge Pack Finished!!! (Pictures Inside)	dsvcustoms	Cosmetics and Lighting Modification Discussions	23	10-15-2009 10:43 PM
New DSV Customs Real Carbon Fiber Back Panel Inserts (Pictures Inside)	dsvcustoms	Cosmetics and Lighting Modification Discussions	3	10-12-2009 01:25 AM