Adding a ZL1 front end to your car.

[01pewterz28]

I think maybe he is looking for one dedicated post with only the required parts with the part numbers and no other comments and maybe it is only updated by 2SSRS the man who knows it all.

Sean

[chevy 3]

Will I need a special rivet gun for the plastic rivets? And what are the nuts for? I thinking the top lip of the bottom grill maybe

[2SSRS@Gen5diy]

Originally Posted by 01pewterz28

I think maybe he is looking for one dedicated post with only the required parts with the part numbers and no other comments and maybe it is only updated by 2SSRS the man who knows it all.

Sean

The OP is updated as of last night.

Originally Posted by chevy 3

Will I need a special rivet gun for the plastic rivets? And what are the nuts for? I thinking the top lip of the bottom grill maybe

Any rivet gun will work, The nuts go on the bumper and when you add the grill the screws go in the gill and thread in to the nuts, by the way its the same nuts for the guys that did the HUD upgrade.

[11 Camaro IBM]

Can you show about where they go? I don't have a rivet gun so what should I do?

[2SSRS@Gen5diy]

Here if you want to add this part back on your new bumper you need the rivets and you need to drill them out of your old bumper.

[Coop]

Originally Posted by 2SSRS

What do you want it to have in the list, I have all the part # in there for the bumper, Or do you want a list for all parts that are on the ZL1?

I saw a couple of pics of parts but wasnt sure whihc ones were necessary. I would suggest a complete list written into the thread stating this is the complete list of part numbers with the quantities need. This would allow someone to print the message and take it their local parts guy and say " This what I need to order". Unless this has already been done and I missed it.

[Darth_Emma]

Originally Posted by Coop

I saw a couple of pics of parts but wasnt sure whihc ones were necessary. I would suggest a complete list written into the thread stating this is the complete list of part numbers with the quantities need. This would allow someone to print the message and take it their local parts guy and say " This what I need to order". Unless this has already been done and I missed it.

It's in the fist post. Scroll down.

[2SSRS@Gen5diy]

Originally Posted by Coop

I saw a couple of pics of parts but wasnt sure whihc ones were necessary. I would suggest a complete list written into the thread stating this is the complete list of part numbers with the quantities need. This would allow someone to print the message and take it their local parts guy and say " This what I need to order". Unless this has already been done and I missed it.

But for what, The front page has all the parts you need to do a car, for the new bumper, Do you want me to add the all the parts for the Hood and rear parts too? that is what i need to know.

[garcmol]

I think I'm going to start ordering some of the hardware and smaller parts. Save the fascia for the finale. Thanks for posting up the schematics and part numbers!

One question: The pics of the rivets and it says you need 10 of them. Does that part # include 10 rivets, or do you order 10 of that part #? I hope that makes sense. Just curious if the part numbers include the quantities needed. Thanks!

[2SSRS@Gen5diy]

The pat # are for only 1 so you need to tell your parts guy you need part X 10 for the rivets or any outer part.

[camaro2lt]

do we need a riviet gun?

[bthibodeaux]

Originally Posted by 11 Camaro IBM

Can you show about where they go? I don't have a rivet gun so what should I do?

You just need a cheap pop rivet gun that you can get at any hardware store for about $10.

Harbor Freight sells the one in the picture for$16, and it is specifically for the poly rivets.

[2SSRS@Gen5diy]

Originally Posted by camaro2lt

do we need a riviet gun?

Originally Posted by bthibodeaux

You just need a cheap pop rivet gun that you can get at any hardware store for about $10.

This^.

[Ray@RDS]

Much to my surprise the ZL1 side skirts arrived! ya hooo!