Treasure Coast Camaro 5 ***TCC5***

[mikepage0007]

last new mod , finished tonight..titanium wrap and dss is sending me a carbon fiber shaft to try out..hmmmmm

[Drago77]

Originally Posted by mikepage0007

last new mod , finished tonight..titanium wrap and dss is sending me a carbon fiber shaft to try out..hmmmmm

Is that the "Magnum" brand wrap????

[G200 Pilot]

Originally Posted by mikepage0007

i have 4 inches clearance with my body kit, also was looking more for hidden hitch...we fabbed a 1 1/4 female to the frame horn recessed behind bottom grille and have a 11 inch 1 1/4 reciever that will slide into and i can throw a pin into it...so its removable..now all i need is a trunk to carry it..lol...

You can always carry it in your "diddy bag"!

[G200 Pilot]

Originally Posted by mikepage0007

last new mod , finished tonight..titanium wrap and dss is sending me a carbon fiber shaft to try out..hmmmmm

I thought you already tried out the carbon fiber shaft... Isn't that the one that unglued?

[mikepage0007]

Originally Posted by Drago77

Is that the "Magnum" brand wrap????

it is the dei brand, best deal online..took 2 50 ft rolls to wrap DEI 010127 2" Titanium Exhaust wrap ....i was trying to reach you to see if you had some thermal shield duct tape... lol

[mikepage0007]

Originally Posted by G200 Pilot

I thought you already tried out the carbon fiber shaft... Isn't that the one that unglued?

yes and yes...it was not dss, also heat was the factor i am 90% sure of...since i am now 2inch and ceramic coated jet hott and exhaust is now wrapped. i shoud hopefully see 30 to 40% temp decrease.especially with no cats...that would drop me somewhere between 200f and 300f along the tranny hump...bond agent should hold at that temps with no problem...space shuttle uses same bond material under heat tiles and 300f is what there max temp rating is...actual failure point is approx 450f per manufacturer..

[Black11SS]

Originally Posted by mikepage0007

yes and yes...it was not dss, also heat was the factor i am 90% sure of...since i am now 2inch and ceramic coated jet hott and exhaust is now wrapped. i shoud hopefully see 30 to 40% temp decrease.especially with no cats...that would drop me somewhere between 200f and 300f along the tranny hump...bond agent should hold at that temps with no problem...space shuttle uses same bond material under heat tiles and 300f is what there max temp rating is...actual failure point is approx 450f per manufacturer..

With the amount of hp and man hours into your car mike, should be able to go as fast as the space shuttle too lmfao

[Drago77]

Thinking about going to the Civic Center Saturday after the Roma's car show for Grouchos Comedy Club and maybe Shindigs after... anyone interested?

Also; don't forget, Sun Aug 12 is the PBIR open test-n-tune/car show/swap meet. 3CC is organizing some head-to head races against a Miami Mustang club... should be a great time; lemme know who's interested, also who's up for the Mustang races, I'll be speaking w him Saturday to go over the details

[1JEWLDSSRS]

Hey Thanks everyone for the kind words and thoughts, it has been a LONG week but everything is good and me and Sis are OK. mom's in a much better place. You folks are a fantastic group and I hope to see you all soon. Thanks again.. Wayne

[UF4LIFE102SS]

Originally Posted by mikepage0007

good luck kev, my latest mod..

I don't c the mirror behind the engine?

[Tyler@ExtremePerformance]

Nope Mirror is GONE! Thanks Darrin!

[mikepage0007]

gave it to paige, maybe she can use it...would not fit with the tranny dipstick and whipple

[Drago77]

Hey guys- just an invite from Tri Co for their BBQ this weekend... its Sunday, from 11-5, Shelter #4. I don't have any more details yet, but I'll find out more tomorrow. I'm sure the info is on their thread... but my phones dying now...

Sounds like an open invite if anyone's interested! :

[Korrosion]

Alright, what do you guys think havoc rear diffuser or zl1 rear diffuser? I have zl1 front bumper and zl1 sides.