Iowa Members Get In Here!

[BenningJ]

Add me in for C5 FEST 4!

[pwrmanpaul66]

They announced the date but not location did I miss a post some where ?

[Snakeater]

Originally Posted by HRD_WRK

I still plan on attending Saturday w my daughter. I need to pick up some tools from my inlaws (not sure if there or in Ames) before or after the open house. My thoughts are to return home by 530 ish. Morning leave time would be most likely around 700-730, depending on inlaw part pickup timeline.

I will be trucking it there and the cab has room for 2-3 more people if you care to tag along. Can meet anywhere along the 380/80 corridoor

Let me know by Friday 330 if via here, or call by 8p friday-see Contact album 2nd picture info-must be logged on: file name= phone #

Tim

Hey Tim just was at karls performance shop
amazing is all i can say got a personal tour from
my buddy that works there carl copo is in front lobby
Next to a sweet vette and to let everyone know
They have a 4 wheel dyno only one in the state
plus top line paint booths
cool place

[toesuf94]

I want to go up but have a deal in the morning that will prevent me from leaving much before 9-10. I guess they will be there a while so if I miss this trip there is always next time.

[Steve_RS_Camaro]

Tim here's the the 3/8 extention selection
1" 3" 6" 10" 20" 36"
which one you need I can bring it Sat. along with the Trans Jack.

[Steve_RS_Camaro]

Originally Posted by HRD_WRK

Maaaaaaaann,
too many tools, too little money.

The largest 2 extensions please - 36" I believe is needed, but 20" also just in case. I can add my assortment of other extensions as needed.

Its like the 1inch diamond laced cement holesaw bit I paid like 50$ for - only to use for 3 holes only 1/2" depth.

I appreciate it.

Too many tools is why too little money.

[xtreme2s]

Originally Posted by HRD_WRK

I still plan on attending Saturday w my daughter.
My thoughts are to return home by 530 ish.
Morning leave time would be most likely around 730-800, but flexible.
I will be trucking it there andthe cab has room for 2-3 more people if you care to tag along. Can meet anywhere along the 380/80 corridoor.

Let me know by Friday 430 if via here, or call by 9p friday or 7ish Sat-see Contact album 2nd picture info-must be logged on: file name= phone #

I'm spending tonight in Des Moines for a meeting, I also will swing by the Karl's Speed. What is the time most planning on going? -mid morning or so?

[pwrmanpaul66]

9:30 or 10:00 or there abouts for me !

[Steve_RS_Camaro]

Originally Posted by xtreme2s

I'm spending tonight in Des Moines for a meeting, I also will swing by the Karl's Speed. What is the time most planning on going? -mid morning or so?

I plan on 10ish.

[OVERPAR73]

Started to get the dynamat installed in the rear seating area, boy this is time consuming. I can't figure out how to remove the top of the rear seat? I still need to do behind there and I've also started in the trunk. This stuff is really nice and it's going to make allot of difference with the road noise.

[INTIMIDAT3R]

Originally Posted by OVERPAR73

Started to get the dynamat installed in the rear seating area, boy this is time consuming. I can't figure out how to remove the top of the rear seat? I still need to do behind there and I've also started in the trunk. This stuff is really nice and it's going to make allot of difference with the road noise.

With the top down, is road noise really a problem?

[Steve_RS_Camaro]

Had a good time at Karl Performance today (good thing I did not bring my credit card I would be broke for the next 20 years) Glad to see all that showed up Paul, Tim, JD, Nancy, Tim, Bob, Dan. Nice place all your performance needs engine, suspension, body, upholstery, and safety gear. Some fine cars out there and some great dyno pulls today.

[Fubar]

Don's ZL1 pulled a 518 hp .. When Dave is done with the car, (Lingenfelter parts) it will be at 780 rwhp..

[xtreme2s]

Originally Posted by Steve_RS_Camaro

Had a good time at Karl Performance today (good thing I did not bring my credit card I would be broke for the next 20 years) Glad to see all that showed up Paul, Tim, JD, Nancy, Tim, Bob, Dan. Nice place all your performance needs engine, suspension, body, upholstery, and safety gear. Some fine cars out there and some great dyno pulls today.

This place is awesome. For my 67, I did sign up for the dyno and tune. they have a guy on staff that does the old school carb's. Finally will get my wild cammed 3 carbed motor some good jetting/tuning via setting on a dyno.

don't know if you guys seen the "fast n furious" group leave.... sounded like a roar of angry bee's, but when I signed up on the sheet for dyno'ing, about 12+ or so cars were import stuff

Tim S