FSP Visits Panama City !!! Pics!!!

[Matt @ FSP]

Ok not on a vacation

We're up here at our buddy Jason's shop once again.. Have a few cars lined up for installs... Short list is

2013 GS Coupe 140 miles- ECS SC1500 Kit (Dyno'd 383rwhp/355rwtq stock)

2010 Camaro SS - 3.91 Gears, FSP Custom Cam Grind Package

2011 Camaro SS - Change cam to FSP Custom Cam Grind, Add FAST 102mm Intake

2012 Camaro SS - We previously built this to 740rwhp (On our Mustang dyno), stock bottom end, automatic transmission. We're bringing it to the drag strip this weekend for some testing on the new combo!

[Ivan @ Southwest Speed]

Bitchin pics!!

[avellanet.jr]

Jason opening the track this weekend for test and tune or just for his use? Let me know, i'd like to watch and/or run lol.

Great work guys!! Glad to see us northerners are keeping you busy!

[spd2612]

Looks like you guys are busy

[Matt @ FSP]

Yep we are ! Dynod a FSP cam only here with SW LTs made 470.9twhp/431rwtq on a LOAD controlled Dynojet so pretty cool to see our numbers are a shade lower on the Mustang dyno vs the load controlled Dynojet. just a FYI for you spd but as we both know the proofs in the ET not the dyno #

[Adadda]

Originally Posted by avellanet.jr

Jason opening the track this weekend for test and tune or just for his use? Let me know, i'd like to watch and/or run lol.

Great work guys!! Glad to see us northerners are keeping you busy!

Not open for the public but you are more than welcome to come out and make some passes while we are out there .

[spd2612]

Originally Posted by Matt @ FSP

Yep we are ! Dynod a FSP cam only here with SW LTs made 470.9twhp/431rwtq on a LOAD controlled Dynojet so pretty cool to see our numbers are a shade lower on the Mustang dyno vs the load controlled Dynojet. just a FYI for you spd but as we both know the proofs in the ET not the dyno #

Yes on the E/T, that still comes in pretty close to the Mustang 9 HP and 5 trq
I have a couple more things to do on mine before I can test the E/T and then I will still have to play nice on the launch, so 60 ft will suffer a little.
Hopeing to see what this combination does maybe someone will beet me to it
The FSP Cam is a little Lopey but it did wake my car up.......
Plus it gets allot of attention at stop lights LOL

[spd2612]

That cam is actually very surprising with a overlap of 11@50 or a total of 61 It pulls very well low to up high in the RPM's It dose not care for Idle though
But who the hell wants to Idle?, Oh damn I forgot that's where it sounds so good .....

He He

[avellanet.jr]

Originally Posted by Adadda

Not open for the public but you are more than welcome to come out and make some passes while we are out there .

Let me know the date/time and I'll see if I can get out there.

Thanks!

[Matt @ FSP]

Originally Posted by avellanet.jr

Let me know the date/time and I'll see if I can get out there.

Thanks!

Shoot me a text tomorrow bud, we're playing it as far as when we get all these cars here done...

---------------

I have an idle clip and I'll post the dyno also from Whisper's! 470rwhp/431rwtq, check out the curve

2010+ SS
- Manual Trans
- SW LTs with Axle Back 3x3 X-Pipe w/ Cats
- FSP Custom Grind 231/239 Cam
- Melling HV Oil Pump
- C5R Timing Chain
- FSP 3.91 Gear Swap (Dyno was before gear swap)

[christianmotox]

Fail. I was expecting other Panama City pics.. LOL

[avellanet.jr]

Originally Posted by Matt @ FSP

Shoot me a text tomorrow bud, we're playing it as far as when we get all these cars here done...

Will do.

I can't imagine how loud Whispers car is now.. it was a screamer before the cam lol.

[spd2612]

That cam made mine louder LOL

Just following your thread Matt
Wait till he rolls it out about 2500 and pushes on the gas
Oh yea
Love mine

[Whisper Jet]

Originally Posted by avellanet.jr

Will do.

I can't imagine how loud Whispers car is now.. it was a screamer before the cam lol.

I can't wait to hear it when Rodney wires up the DMH cutouts that are installed.