You are browsing camaro5 
 |
|
04-27-2013, 09:37 PM
|
#1 |
 Drives: Black 2ss Join Date: Jul 2011
Location: Amarillo, tx
Posts: 272
|
SLP LTs, xpipe, and loudmouth 2 question
Just had all these installed... sounds awesome but I have a question.
The crossover plate is touching the resonators... is this install error? Is it normal for it to touch? Can I remove the plate? I just dont like the Idea of the plate rubbing on the resonators... any help would be appreciated. |
|
|
|
04-28-2013, 12:01 PM
|
#2 |
  Drives: 2011 2SS Join Date: Jan 2013
Location: DFW, TX
Posts: 931
|
It will bang on that. There are a few companies that make one that is made for 3" exhaust. They aren't too expensive either.
|
|
|
|
|
05-01-2013, 10:58 PM
|
#3 |
|
Serious Sleeper
Drives: 2010 CGM 2SS/RS M6 Join Date: Nov 2008
Location: Lexington,SC
Posts: 3,129
|
I used a 3/4" thick aluminum block cut to fit the mounting brackets. Painted black and drilled the same as the bolts that I bought at home depot. Those resonators need clearance, I'll post a pic of what I have if you like.
__________________
***************************************
Drive-by Fact of Life: After Monday and Tuesday even the calendar reads... W T F  *************************************** |
|
|
|
|
05-05-2013, 02:05 AM
|
#4 | |
|
Drives: Black 2ss Join Date: Jul 2011
Location: Amarillo, tx
Posts: 272
|
Quote:
|
|
|
|
|
|
05-05-2013, 08:45 PM
|
#5 |
|
Serious Sleeper
Drives: 2010 CGM 2SS/RS M6 Join Date: Nov 2008
Location: Lexington,SC
Posts: 3,129
|
Best I could do for now without jacking the car, but this set up gives me 1/4" clearance between the brace and the resonators.
__________________
***************************************
Drive-by Fact of Life: After Monday and Tuesday even the calendar reads... W T F *************************************** |
|
|
|
|
05-05-2013, 09:59 PM
|
#6 |
Drives: Camaro SS2/RS orange/black stripes Join Date: Feb 2010
Location: Louisville KY
Posts: 570
|
Nothing should the exhaust but rubber or the noise will travel into the cab. Don't remove the tunnel brace. The chassis will flex on a hard take off.
__________________
2010/2SS/RS/6L80E/Mast built LS3 416 Stroker/Black Lable Heads/Blower Cam/Jannetty Tuned/ 685rwhp/635tq/KookHeaders/3"exhaust/Magnaflows/Whipple Blower/10lbs bst/Duel pumps/85lb inj/2 gauge pillar/CAI/RX catch can/Vmax ported TB/Lexani LX15s/Pedders sub F bushings inserts/Pedders sport extreme coilovers/ZL1 sway bars/Hotchkis strut tower brace/Hawk brake pads/stainless steel brake lines/CTV front calibers/slotted rotors 15"/1 pc drive shaft & loop/hidden radar-laser detect/rear louvers/terminator hood/ SS mats/black outs/Bowties/GM GFX kit/blade spoiler/deading matting/wolf art/
|
|
|
|
|
|
|
|
 |
|
|
