SOLD: Forgestar CF5V gloss black 19x10, 19x11, brand new, PRICE DROP!

[L99CAMA2011]

Originally Posted by Inferno LS3

Let me see if I get my 22" sold and ill jump on these for track wheels.

If you jump on them you may bend them.

[Inferno LSX]

Originally Posted by L99CAMA2011

If you jump on them you may bend them.

I'm not that much of a fatty. LOL.

[Astoc]

I updated the first post with some information/pictures regarding the weight of the 19x10 wheels.

[L99CAMA2011]

I'll take them bro. Now someone buy my freaking TSW Nurburgrings, please.

[L99CAMA2011]

Originally Posted by SUX2BU

Too bad it's not a square set up.

If they were square then they wouldn't roll now would they SUX, LOL.

[Astoc]

Sale pending.

[Donovanl1685]

Would these have any issues fitting a ZL1?

[nitto85]

Are there any pictures out there of the CF5V's on a camaro yet?

[Astoc]

Originally Posted by Donovanl1685

Would these have any issues fitting a ZL1?

These would be a very similar fitment to the stock ZL1 wheels, except smaller in diameter. As of right now, these are pending sale, though.

Originally Posted by mst504

Are there any pictures out there of the CF5V's on a camaro yet?

I haven't been able to find a single picture. Hopefully, the buyer posts pictures of these on his car.

[collinsRS]

Congrats man, GREAT looking wheels, and the buyer is getting a deal!

[Astoc]

Sale is no longer pending.

These wheels are still available.

[L99CAMA2011]

Originally Posted by Donovanl1685

Would these have any issues fitting a ZL1?

I have 19x9.5" that was meant for the ZL-1 on TireRack site. These should be better fitting as long as they clear the front breaks.

[Astoc]

UPDATE:

A board member contacted me with some concerns about the front wheels supposedly being +35 offset. He stated that the ZL1 front offsets are +23 for 20x10, and an offset of +35 might not clear the OEM shocks with a 295/35-19 tire. I felt that this warranted some investigation on my part.

So, here's a bit of explanation and some interesting information that I just found out:

When I ordered these wheels, I requested offsets that would allow me to fit 295/35-19 tires in the front on a 19x10 wheel.

Later on, after I received the wheels and went to sell them, I sent an email to Jurrian asking him what offsets were chosen for the wheels. Potential buyers had been asking me what the offsets were, and I wanted to be able to give them an answer. Jurrian replied that the wheels were probably no different than the usual, which is +35 front and +39 rear.

Now, I just took one of the 19x10 wheels out of the box and began measuring the wheel. Here's what I found:

• From the outside of the outer lip to the outside of the inner lip is 275mm (10.82").
• From the inside of the outer lip to the inside of the inner lip is 254mm (10.00").
• From the inside of the outer lip to the outside of the inner lip is 265mm (10.43").
• From the mounting surface to the outside of the inner lip is 165mm (6.49").
• Subtract 10" (the actual wheel width) from 10.43" and you get 0.43", which is the width of the inner lip.
• Subtract the inner lip width, 0.43", from 6.49". As the wheel is 10" wide inside of the outer and inner lips, subtract half of that width from 6.09" to get the distance that the mounting surface is offset from the centerline of the wheel.
• The offset would be 6.09" - 5.00", which is 1.09". That converts to 27.69mm offset.

Obviously, there is some margin of error here. However, it is quite apparent to me that the offsets of these front wheels are more akin to the ZL1 front offset of +23.

[L99CAMA2011]

Originally Posted by Astoc

UPDATE:

A board member contacted me with some concerns about the front wheels supposedly being +35 offset. He stated that the ZL1 front offsets are +23 for 20x10, and an offset of +35 might not clear the OEM shocks with a 295/35-19 tire. I felt that this warranted some investigation on my part.

So, here's a bit of explanation and some interesting information that I just found out:

When I ordered these wheels, I requested offsets that would allow me to fit 295/35-19 tires in the front on a 19x10 wheel.

Later on, after I received the wheels and went to sell them, I sent an email to Jurrian asking him what offsets were chosen for the wheels. Potential buyers had been asking me what the offsets were, and I wanted to be able to give them an answer. Jurrian replied that the wheels were probably no different than the usual, which is +35 front and +39 rear.

Now, I just took one of the 19x10 wheels out of the box and began measuring the wheel. Here's what I found:

• From the outside of the outer lip to the outside of the inner lip is 275mm (10.82").
• From the inside of the outer lip to the inside of the inner lip is 254mm (10.00").
• From the inside of the outer lip to the outside of the inner lip is 265mm (10.43").
• From the mounting surface to the outside of the inner lip is 165mm (6.49").
• Subtract 10" (the actual wheel width) from 10.43" and you get 0.43", which is the width of the inner lip.
• Subtract the inner lip width, 0.43", from 6.49". As the wheel is 10" wide inside of the outer and inner lips, subtract half of that width from 6.09" to get the distance that the mounting surface is offset from the centerline of the wheel.
• The offset would be 6.09" - 5.00", which is 1.09". That converts to 27.69mm offset.

Obviously, there is some margin of error here. However, it is quite apparent to me that the offsets of these front wheels are more akin to the ZL1 front offset of +23.

My 19x9.5 Enkei is 35mm ofset so 19x10 being 28mm approx, 7mm more outwards seems correct plus my Enkei fit like .5" inwards which I didn't like. These would fit perfect and i have 1LE/ZL-1 front hubs on my car.