Exhaust- correct me if I'm wrong.. - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

FlashBurntFace · 02-18-2014, 08:13 PM

My car has had 2 previous owners.. Did one of them delete the resonator already? 2010 SS/RS m6

FlashBurntFace · 02-18-2014, 08:22 PM

canecorso69 · 02-18-2014, 08:42 PM

It appears so.

FlashBurntFace · 02-18-2014, 09:40 PM

Quote:

Originally Posted by canecorso69

It appears so.

It seems like that's all they had done to the exhaust... Is deleting the resonator worth the trouble of cutting it out. I'm wondering why they didn't put an x pipe in its place instead of 2 straight sections..

axis · 02-19-2014, 11:27 AM

Take a wider pic. Those buldges in the rear look like they could be the resonators. There "should" be a crossover tube near them that's the H pipe. I have no idea what they cut out, unless those buldges are bullet mufflers.

Iam Broke · 02-19-2014, 02:00 PM

Looks like they cut out the "H". I think the LS3 resonators are still back there. Prob had an "X" welded in and took it out. No other reason to replace that much pipe.

FlashBurntFace · 02-19-2014, 02:46 PM

If I'm not mistaken, this big clunky thing on the right is the stock resonator which fits up underneath the heat shield. I'm Ultimately trying to figure out what went/fits where because I'm ordering long tubes, cats, x pipe (which should fit where the resonator was) and a muffler delete axle back

Badbubba · 02-19-2014, 02:59 PM

^^^ that exhaust is for a L99. LS3 does not have that huge resonator. LS3 just has a small bulge in each each pipe and an H pipe after the cats, when the 2 exhaust pipes start to run parallel. Also L99 and LS3 mufflers look the same on the outside, but are different on the inside.

Badbubba · 02-19-2014, 03:16 PM

http://www.camaro5.com/forums/attach...1&d=1301717957
L99 left, LS3 right.
http://www.camaro5.com/forums/showth...ht=ls3+muffler
http://www.camaro5.com/forums/showth...ht=L99+muffler

nyrfan · 02-19-2014, 03:44 PM

Looks like a stock LS3 exhaust to me, not modified.

FlashBurntFace · 02-19-2014, 05:07 PM

Ahh I didn't know l99 had different exhaust setup. Any recommendations for an x pipe? And do I want the "x" right about where the H was?

mikeyg36 · 02-19-2014, 05:16 PM

Looks stock.

JDP Sales · 02-19-2014, 05:29 PM

Quote:

Originally Posted by axis

Take a wider pic. Those buldges in the rear look like they could be the resonators. There "should" be a crossover tube near them that's the H pipe. I have no idea what they cut out, unless those buldges are bullet mufflers.

My thoughts exactly. It looks like the pic was taken next to the H pipe and just before the resonators.

But to answer your question O.P. I suggest going with the Magnaflow X pipe Part # 10791.

Best regards,

Tyler
888-308-6007

RA1987 · 02-19-2014, 05:29 PM

Stock

02-18-2014, 08:13 PM	#1
FlashBurntFace Drives: 10' 2SS/RS, LS3, CAI Join Date: Dec 2013 Location: Auburn, Indiana Posts: 198	Exhaust- correct me if I'm wrong.. My car has had 2 previous owners.. Did one of them delete the resonator already? 2010 SS/RS m6 Attached Images

02-19-2014, 11:27 AM	#5
axis Search Ninja Drives: 2010 Black 2SS/RS A6 Join Date: Oct 2009 Location: Central Ark Posts: 7,183	Take a wider pic. Those buldges in the rear look like they could be the resonators. There "should" be a crossover tube near them that's the H pipe. I have no idea what they cut out, unless those buldges are bullet mufflers. __________________ 2010 Black 2SS/RS A6 Halltech CF 102 fed GPI modded intake manifold Bo (knows) White ported TB Kooks LT's/ Dynomax VT Pfadted (springs/sways) Dyno tuned by Rhino and GPI I once parallel parked a train.

02-19-2014, 02:00 PM	#6
Iam Broke PHAT B33 Drives: 2012 TF3 Camaro 2SS/RS M6 Join Date: Jun 2012 Location: Dark of the Moon Posts: 1,460 View My Garage	Looks like they cut out the "H". I think the LS3 resonators are still back there. Prob had an "X" welded in and took it out. No other reason to replace that much pipe. __________________ Another 1 of 371 '12 T3 LS3 M6's built.

02-19-2014, 02:46 PM	#7
FlashBurntFace Drives: 10' 2SS/RS, LS3, CAI Join Date: Dec 2013 Location: Auburn, Indiana Posts: 198	If I'm not mistaken, this big clunky thing on the right is the stock resonator which fits up underneath the heat shield. I'm Ultimately trying to figure out what went/fits where because I'm ordering long tubes, cats, x pipe (which should fit where the resonator was) and a muffler delete axle back Attached Images

02-19-2014, 02:59 PM	#8
Badbubba GrINned & JUICEd Drives: 15STI, 10Expy, 10 2SS/RS M6, 47KB1 Join Date: Nov 2009 Location: Pittsburgh, PA Posts: 1,251	^^^ that exhaust is for a L99. LS3 does not have that huge resonator. LS3 just has a small bulge in each each pipe and an H pipe after the cats, when the 2 exhaust pipes start to run parallel. Also L99 and LS3 mufflers look the same on the outside, but are different on the inside. __________________ GPI SS3 Cam & stuff,N.O. Plate(dedicated fuel tank,progressive,fuel hose upgrade,remote opener,heater,console switches),LNC2000,CTAP,ARH 1 7/8" LTs/gutted cats/X pipe/mufflers,Jet Hot coated LTs,GPI HPT Tune,CAI, Scoop,Rx Catch Can,Gates heater hose relocation, Remote clutch & auto brake res,Metco loop,Momentum Tunnel Brace,TSW Nurb 18",555 & 05,Pfadt trailing arms & toe rods,Autometer WB,Fesler Pillar Pod,LED strips (int),Lloyds floor & trunk mats,LED DRL/front turn & license plate,DRL harness,VLEDs tail lights,Plasticoat Bowties. Ord: Oct 5, 2009 Rec: Nov 19, 2009 13.17@112.6 stock

02-18-2014, 08:22 PM	#2
FlashBurntFace Drives: 10' 2SS/RS, LS3, CAI Join Date: Dec 2013 Location: Auburn, Indiana Posts: 198

02-18-2014, 08:42 PM	#3
canecorso69 run ur car not ur mouth Drives: 2013 1LE Join Date: Jul 2013 Location: Middletown, DE; Mayfield, NY Posts: 1,220	It appears so.

02-19-2014, 03:16 PM	#9
Badbubba GrINned & JUICEd Drives: 15STI, 10Expy, 10 2SS/RS M6, 47KB1 Join Date: Nov 2009 Location: Pittsburgh, PA Posts: 1,251	http://www.camaro5.com/forums/attach...1&d=1301717957 L99 left, LS3 right. http://www.camaro5.com/forums/showth...ht=ls3+muffler http://www.camaro5.com/forums/showth...ht=L99+muffler __________________ GPI SS3 Cam & stuff,N.O. Plate(dedicated fuel tank,progressive,fuel hose upgrade,remote opener,heater,console switches),LNC2000,CTAP,ARH 1 7/8" LTs/gutted cats/X pipe/mufflers,Jet Hot coated LTs,GPI HPT Tune,CAI, Scoop,Rx Catch Can,Gates heater hose relocation, Remote clutch & auto brake res,Metco loop,Momentum Tunnel Brace,TSW Nurb 18",555 & 05,Pfadt trailing arms & toe rods,Autometer WB,Fesler Pillar Pod,LED strips (int),Lloyds floor & trunk mats,LED DRL/front turn & license plate,DRL harness,VLEDs tail lights,Plasticoat Bowties. Ord: Oct 5, 2009 Rec: Nov 19, 2009 13.17@112.6 stock

02-19-2014, 03:44 PM	#10
nyrfan Let's go Rangers! Drives: 13' AGM 2SS/RS L99 Join Date: Jun 2011 Location: Orlando, FL Posts: 10,742 View My Garage	Looks like a stock LS3 exhaust to me, not modified. __________________ Soprano 4/1/00-6/14/11, Gone but NEVER forgotten! FSP tuned: 377/389 Last edited by nyrfan; 02-19-2014 at 05:30 PM.

02-19-2014, 05:07 PM	#11
FlashBurntFace Drives: 10' 2SS/RS, LS3, CAI Join Date: Dec 2013 Location: Auburn, Indiana Posts: 198	Ahh I didn't know l99 had different exhaust setup. Any recommendations for an x pipe? And do I want the "x" right about where the H was?

02-19-2014, 05:16 PM	#12
mikeyg36 Drives: 2015 Z/28 #533 Join Date: Jul 2012 Location: NY Posts: 6,732	Looks stock.

02-19-2014, 05:29 PM	#14
RA1987 Drives: SS Join Date: Mar 2013 Location: 92129 Posts: 489 View My Garage	Stock