How Many Use The DashLogic on there ZL1? - Page 12 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ZL1_TA · 09-06-2014, 01:33 AM

Had mine freeze three times today... first time since I started using it. I did just install a cable so I could re-locate but don't think that is the issue because it worked fine for a couple of days after the cable install. The only thing different about today is a car wash where they start the car and move it very short distances a couple of times... probably not enough time for a complete boot.

Guessing this might cause the issue. Luckily I mounted it on Velcro where I can reach it... to re-boot I just flip the switch to config then back to the profile I want.... seems to be back to normal now.... hoping it stays that way.... maybe another firmware update is needed?

BoostedX2 · 09-06-2014, 05:42 AM

Quote:

Originally Posted by RLHMARINES

May radio display for Dashlogic comes on but I also must hit the command button on the radio and hit the back button for the read outs to stay on the radio. I sometimes while driving will have to toggle the switch to config and then back to profile to reset it.

I hit INFO and the dash logic readout stays....

camguynj · 09-06-2014, 10:02 AM

Quote:

Originally Posted by ZL1_TA

Had mine freeze three times today... first time since I started using it. I did just install a cable so I could re-locate but don't think that is the issue because it worked fine for a couple of days after the cable install. The only thing different about today is a car wash where they start the car and move it very short distances a couple of times... probably not enough time for a complete boot.

Guessing this might cause the issue. Luckily I mounted it on Velcro where I can reach it... to re-boot I just flip the switch to config then back to the profile I want.... seems to be back to normal now.... hoping it stays that way.... maybe another firmware update is needed?

What version are you using? When mine froze with v1.17 on my '13 Palmer said to pull the Cluster fuse for 20secs to reboot Dashlogic, just switching from Config to Profile didn't unfreeze it.

ZL1_TA · 09-06-2014, 11:48 AM

Quote:

Originally Posted by camguynj

What version are you using? When mine froze with v1.17 on my '13 Palmer said to pull the Cluster fuse for 20secs to reboot Dashlogic, just switching from Config to Profile didn't unfreeze it.

I am using the latest...1.18a

ZL1_TA · 09-13-2014, 05:07 PM

Quote:

Originally Posted by ZL1_TA

Had mine freeze three times today... first time since I started using it. I did just install a cable so I could re-locate but don't think that is the issue because it worked fine for a couple of days after the cable install. The only thing different about today is a car wash where they start the car and move it very short distances a couple of times... probably not enough time for a complete boot.

Guessing this might cause the issue. Luckily I mounted it on Velcro where I can reach it... to re-boot I just flip the switch to config then back to the profile I want.... seems to be back to normal now.... hoping it stays that way.... maybe another firmware update is needed?

I have come to the conclusion that the freezing is caused by the extension cable that I bought... when plugged in directly there are no issues. Really don't need a cable just a right angle adapter. I looked but didn't find any... does anyone have a link to one?

Bigtime53 · 09-13-2014, 08:19 PM

Quote:

Originally Posted by ZL1_TA

I have come to the conclusion that the freezing is caused by the extension cable that I bought... when plugged in directly there are no issues. Really don't need a cable just a right angle adapter. I looked but didn't find any... does anyone have a link to one?

Hold on because mine has froze up before and it is plugged directly in also. I have not driven my car in several weeks but if it starts freezing up I will have to do the update to it.

2013 ZL1 #7860 · 09-13-2014, 08:33 PM

I never could get the cables to work. Instead I just relocated the OBD port under the dash with a few zip ties. You can't tell at all and it is still available to use if needed.

Aussie ZL1 · 09-15-2014, 09:58 AM

My dash logic turned up Down Under a couple of weeks ago.
Like most of you, I love the product...
I'm an Engineer, so having all that Data on display is awesome.

I've had the system freeze once, so reached down and pulled the module and reinserted it to reset.

I thought that the "no show" on the My Link screen was something to do with the right hand drive conversion... But after about a week, I got a display, then after a few minutes it disappeared. Now it just seems to come and go randomly.
I think I'll just turn that display off...

I love having the bimodal exhaust switch on the steering wheel..

I'm not disappointed with the product, there are a few bugs to fix though and the instructions could do with a bit more info....

Cheers

BaylorCamaro · 09-16-2014, 04:35 PM

So ever since using my Dash Logic my nav has not worked. It says that I'm using OnStar for directions and need to cancel that route. I don't even have OnStar. I have a 2013 ZL1 and my Dash Logic came with version 1.17, this really hasn't been an issue since I don't use nav much. However I'm going on a road trip starting Friday. Anyone know how to solve this? Do I need to flash version 1.16 on it?

Also, I tried unplugging it and restarting my car. I get the same message..

camguynj · 09-16-2014, 11:24 PM

Quote:

Originally Posted by BaylorCamaro

So ever since using my Dash Logic my nav has not worked. It says that I'm using OnStar for directions and need to cancel that route. I don't even have OnStar. I have a 2013 ZL1 and my Dash Logic came with version 1.17, this really hasn't been an issue since I don't use nav much. However I'm going on a road trip starting Friday. Anyone know how to solve this? Do I need to flash version 1.16 on it?

Also, I tried unplugging it and restarting my car. I get the same message..

See my post #79 ...after v1.15 Palmer made a major change for the '14 my link which is not fully compatible with '10-'13

Sven59 · 09-16-2014, 11:25 PM

What's the most dependable version out there for a 13 without nav?

BaylorCamaro · 09-16-2014, 11:27 PM

Quote:

Originally Posted by camguynj

See my post #79 ...after v1.15 Palmer made a major change for the '14 my link which is not fully compatible with '10-'13

Oh, so 1.15 is the stable version for a 2013? I thought it was 1.16

camguynj · 09-16-2014, 11:27 PM

Quote:

Originally Posted by Sven59

What's the most dependable version out there for a 13 without nav?

V1.15

Sven59 · 09-16-2014, 11:31 PM

Thanks, I will give it a try.

09-06-2014, 01:33 AM	#155
ZL1_TA Drives: 2013 ZL1 Join Date: Mar 2014 Location: CA Posts: 22	Freezing Issue Had mine freeze three times today... first time since I started using it. I did just install a cable so I could re-locate but don't think that is the issue because it worked fine for a couple of days after the cable install. The only thing different about today is a car wash where they start the car and move it very short distances a couple of times... probably not enough time for a complete boot. Guessing this might cause the issue. Luckily I mounted it on Velcro where I can reach it... to re-boot I just flip the switch to config then back to the profile I want.... seems to be back to normal now.... hoping it stays that way.... maybe another firmware update is needed?

09-15-2014, 09:58 AM	#162
Aussie ZL1 Drives: 2013 ZL1 manual RHD Join Date: Dec 2013 Location: Melbourne, Australia Posts: 73	My dash logic turned up Down Under a couple of weeks ago. Like most of you, I love the product... I'm an Engineer, so having all that Data on display is awesome. I've had the system freeze once, so reached down and pulled the module and reinserted it to reset. I thought that the "no show" on the My Link screen was something to do with the right hand drive conversion... But after about a week, I got a display, then after a few minutes it disappeared. Now it just seems to come and go randomly. I think I'll just turn that display off... I love having the bimodal exhaust switch on the steering wheel.. I'm not disappointed with the product, there are a few bugs to fix though and the instructions could do with a bit more info.... Cheers __________________ Brad Dunstan RHD '13 M6 ZL1

09-16-2014, 04:35 PM	#163
BaylorCamaro Track > 1/4 Mile Drives: 2016 C7 Z51 Join Date: Sep 2009 Location: League City, TX Posts: 6,072 View My Garage	So ever since using my Dash Logic my nav has not worked. It says that I'm using OnStar for directions and need to cancel that route. I don't even have OnStar. I have a 2013 ZL1 and my Dash Logic came with version 1.17, this really hasn't been an issue since I don't use nav much. However I'm going on a road trip starting Friday. Anyone know how to solve this? Do I need to flash version 1.16 on it? Also, I tried unplugging it and restarting my car. I get the same message.. __________________ Automotive YouTube Channel / Texas World Speedway / MSR Houston

09-16-2014, 11:25 PM	#165
Sven59 HAMMER PILOT Drives: 13 ZL1#182, 85 CJ7, 16 Silverado Join Date: Nov 2011 Location: Tucson AZ Posts: 4,387	What's the most dependable version out there for a 13 without nav? __________________ "DO YOU WANT ME TO PUT THE HAMMER DOWN?"

09-16-2014, 11:31 PM	#168
Sven59 HAMMER PILOT Drives: 13 ZL1#182, 85 CJ7, 16 Silverado Join Date: Nov 2011 Location: Tucson AZ Posts: 4,387	Thanks, I will give it a try. __________________ "DO YOU WANT ME TO PUT THE HAMMER DOWN?"

09-13-2014, 08:33 PM	#161
2013 ZL1 #7860 Drives: 2013 ZL1 A6 #7860 Join Date: Apr 2014 Location: CO, USA Posts: 1,279	I never could get the cables to work. Instead I just relocated the OBD port under the dash with a few zip ties. You can't tell at all and it is still available to use if needed.