ADM TEXAS MILE 1LE TT BUILD - Page 8 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ADM PERFORMANCE · 10-27-2014, 07:43 AM

We went 200.4 in this car Sunday morning oct 26th 2014

TX/ZL1 · 10-27-2014, 08:11 AM

Quote:

Originally Posted by ADM PERFORMANCE

We went 200.4 in this car Sunday morning oct 26th 2014

HP_Therapy · 10-27-2014, 12:03 PM

Quote:

Originally Posted by ADM PERFORMANCE

We went 200.4 in this car Sunday morning oct 26th 2014

Job well done Sir!!

2010SSRSM6 · 10-27-2014, 01:23 PM

Andy,

Did you get any pic's of the custom roll bar job you guys did on this? Just curious as to if there are any differences in what is required for the mile compared to what is required for a 10.0 in the 1/4 mile?

Impressive build.

10aSSee D · 10-27-2014, 02:55 PM

I knew you guys would do it!!

ADM PERFORMANCE · 10-28-2014, 06:37 AM

Quote:

Originally Posted by 10aSSee D

I knew you guys would do it!!

Thanks as it did not come without some work and effort.

Cheetoh · 10-30-2014, 10:40 PM

Great Job Andy!!

eviltech72 · 11-03-2014, 04:45 PM

😍

Trackman · 11-03-2014, 10:52 PM

Quote:

Originally Posted by ADM PERFORMANCE

Thanks as it did not come without some work and effort.

The only work and effort I saw was gettin up early to get this car in line.(Didn't actually see it as I was sleeping) Put a little fuel in it and put Iceman in the driver seat. Job done.

ADM PERFORMANCE · 11-04-2014, 06:25 AM

Quote:

Originally Posted by Trackman

The only work and effort I saw was gettin up early to get this car in line.(Didn't actually see it as I was sleeping) Put a little fuel in it and put Iceman in the driver seat. Job done.

That 5 am shit sucks ........Still waiting on the results.We had 3 cars over 200mph ,I think most out of 1 shop.

ADM PERFORMANCE · 12-29-2014, 06:12 PM

We now offer these cars turn key - Starting at $75,000

pincushin3819 · 12-30-2014, 06:26 AM

Can you make a new thread Andy & give in detail what $75K will get me/us? I was looking at modding my C7 or buying a Z06 but I would like to know more about your turn key cars? Thanks!

ADM PERFORMANCE · 12-30-2014, 09:54 AM

Quote:

Originally Posted by pincushin3819

Can you make a new thread Andy & give in detail what $75K will get me/us? I was looking at modding my C7 or buying a Z06 but I would like to know more about your turn key cars? Thanks!

These cars are all 2014 -2015 1LE Cars.They are built to order as you have the option to add the standard GM UPGRADES

Powertrain: ADM 417 Engine
Parts included in base engine
GM LS3 aluminum block - 4.070 bore
Water jacket plugs, oil galley & cam bearings
Mahle forged aluminum pistons
Callies 4340 forged steel -58x reluctor
Callies billet steel 6.125 H beam connecting rods
Clevite heavy duty HN rod bearings
GMPP Ported LS3 Heads
LS9Camshaft with Custom dual valvesprings
Ported LS3 Intake manifold
Holley Black Valvecovers
1000cc Injectors
Squash Twin Walbro Fuel pump system
Weldon regulator and all stainless steel hard lines as well as GM factory lines.
AGP Twin Turbo System with air to air intercooler
Twin Ball bearing Garrett Turbos - Rated at 575hp ea
Centerforce DYAD twin disc clutch - Rated at 1200+ftlb torque

Boost Controller
PCS D-200 Datalogger with Boost by MPH and RPM
Fully programmable

Gears
3.23 gear ratio

Brakes
6 piston Brembo brakes with 2 piece Rotors

Fuel
Minimum Octane 93 (More horsepower can be attained with higher Octane fuel

Options:
Brembo 6 piston front calipers and 2 piece rotors
3" Magnaflow Exhaust
Ultra Intercooler for Drag Racing or Texas Mile racing only
Liquid Intercooler Intake by Lingenfelter for Drag Racing or Texas Mile racing only
1200 Hp LSX 427
Larger upgraded turbos
Eibach Springs
ADM 15" Drag Pack
RPS Triple Carbon Clutch

firefighter1 · 01-31-2015, 11:38 AM

Quote:

Originally Posted by ADM PERFORMANCE

These cars are all 2014 -2015 1LE Cars.They are built to order as you have the option to add the standard GM UPGRADES

Powertrain: ADM 417 Engine
Parts included in base engine
GM LS3 aluminum block - 4.070 bore
Water jacket plugs, oil galley & cam bearings
Mahle forged aluminum pistons
Callies 4340 forged steel -58x reluctor
Callies billet steel 6.125 H beam connecting rods
Clevite heavy duty HN rod bearings
GMPP Ported LS3 Heads
LS9Camshaft with Custom dual valvesprings
Ported LS3 Intake manifold
Holley Black Valvecovers
1000cc Injectors
Squash Twin Walbro Fuel pump system
Weldon regulator and all stainless steel hard lines as well as GM factory lines.
AGP Twin Turbo System with air to air intercooler
Twin Ball bearing Garrett Turbos - Rated at 575hp ea
Centerforce DYAD twin disc clutch - Rated at 1200+ftlb torque

Boost Controller
PCS D-200 Datalogger with Boost by MPH and RPM
Fully programmable

Gears
3.23 gear ratio

Brakes
6 piston Brembo brakes with 2 piece Rotors

Fuel
Minimum Octane 93 (More horsepower can be attained with higher Octane fuel

Options:
Brembo 6 piston front calipers and 2 piece rotors
3" Magnaflow Exhaust
Ultra Intercooler for Drag Racing or Texas Mile racing only
Liquid Intercooler Intake by Lingenfelter for Drag Racing or Texas Mile racing only
1200 Hp LSX 427
Larger upgraded turbos
Eibach Springs
ADM 15" Drag Pack
RPS Triple Carbon Clutch

Got a car in the garage waiting! Where's my quote ANDY!!!!! lol!!!

10-27-2014, 01:23 PM	#102
2010SSRSM6 Drives: My wife crazy with my C5 usage. Join Date: Apr 2009 Location: DFW Posts: 6,553 View My Garage	Andy, Did you get any pic's of the custom roll bar job you guys did on this? Just curious as to if there are any differences in what is required for the mile compared to what is required for a 10.0 in the 1/4 mile? Impressive build. __________________ UNDER CONSTRUCTION......again......

10-27-2014, 02:55 PM	#103
10aSSee D Drives: Silver 2010 SS Camaro Join Date: Jul 2009 Location: TN Posts: 2,562	I knew you guys would do it!! __________________ MODS: ADM built 417, 2.9L Whipple with 3.250 pulley, ADM ported and polished LSA heads,ADM stage3 cam,ADM LSA belt drive system,ADM CAI race scoop, ADM dual fuel pumps, ID 850's, BMR full suspension, Gforce 9 inch kit with 3.5 inch driveshaft, Street Slayer twin carbon clutch, Lingenfelter oil seperator. Tuned by built by ADM Performance, 763rwhp,705rwtq

10-30-2014, 10:40 PM	#105
Cheetoh Drives: 2011 Callaway SC572, 2000 Firehawk Join Date: Nov 2009 Location: Irving, TX Posts: 468	Great Job Andy!! __________________

11-03-2014, 04:45 PM	#106
eviltech72 Drives: 2011 Camaro SS/RS package Join Date: Sep 2013 Location: Rochester, NY Posts: 52	😍 __________________ 2011 MIO SS/RS M6- CAI - Kooks LT Header, HF Cats w/ 3in Piping - UDP - PTB - CAM- Hotchkis 1in Lowering Springs - ZL1 Factory Reproduction Rims - Performance Tuned by New Era Performance.

12-29-2014, 06:12 PM	#109
ADM PERFORMANCE Drives: Anything I want Join Date: Oct 2008 Location: DfW - Texas Posts: 5,408	We now build these turn key ready to go. We now offer these cars turn key - Starting at $75,000

10-27-2014, 07:43 AM	#99
ADM PERFORMANCE Drives: Anything I want Join Date: Oct 2008 Location: DfW - Texas Posts: 5,408	We went 200.4 in this car Sunday morning oct 26th 2014

12-30-2014, 06:26 AM	#110
pincushin3819 Drives: 11 AGP TT SS, 14 ECS C7 Join Date: May 2012 Location: Anderson, SC Posts: 352	Can you make a new thread Andy & give in detail what $75K will get me/us? I was looking at modding my C7 or buying a Z06 but I would like to know more about your turn key cars? Thanks!