![]() |
![]() |
#1 |
![]() |
ZL1 side skirts
Pics below:
Just curious about the fitment if everyone's ZL1 sideskirts they may have installed on their 1LE. Mine seem to be sticking out about 1/4 inch at the top edge of the skirt, bottom edge of the door. i cant remember what it looked like before and didn't take the proper angle photos that would make me feel better. i have been meaning to stop by dealership to get a look at stock but haven't as of yet. just curious, I'm gonna try and post some pics, thanks. Last edited by brilll; 01-18-2015 at 09:15 PM. |
![]() |
![]() |
![]() |
#2 |
Todd
|
post some pics and we can given you an answer right away, plenty of us have done this
|
![]() |
![]() |
![]() |
#3 |
![]() |
Im trying. Dont really know what im doing wrong.
|
![]() |
![]() |
![]() |
#4 |
![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Sounds like the clips might not have gone in.
__________________
|
![]() |
![]() |
![]() |
#5 |
![]() |
I don't have any close-ups, but I think you can see that they are flush with the door and rear side panel....
__________________
PR
---------------------------------------------- 2014 CRT 2SS/RS 1LE ![]() Dual-Mode, Recaros, Sunroof, Nav ---------------------------------------- ZL1 Rockers RPI Stealth Splash Guards De-badged (except blacked-out front bowtie) |
![]() |
![]() |
![]() |
#6 |
KaBoom1701
Drives: 13' ZL1 Red M6 Join Date: Dec 2012
Location: I.E. SoCal (Yucaipa)
Posts: 8,630
|
When I install the ZL1 rockers on my V6 everything fit flush...double check that you have all the clips lined up and "snapped" in place.
__________________
Mods:
Roto-Fab Intake, WW Res. kit & Big Gulp Air Scoop, Elite Catch Can, ATI Super Damper & 18% OD Pulley, LF Idler pulley bracket, Metco CC breather, ID850 Injectors, Stainless Power Headers w/ ceramic coating, TR71X Spark Plugs, JMS Fuel Pump Booster, Bo White TB, Tuned by Ted @ Jannetty Racing, Ron Davis HX, D3 Reservoir, Pfadt 1" Springs, Moreno Camber Plates, ZL1 Addons Splitter guard washers, Tow Hook kit & rock guards, Hurst Shifter Billet Plus 6 Speed Short Shifter, ZL1 DRL lighting harness, ZL1 Recaro Seats. |
![]() |
![]() |
![]() |
#7 |
Drives: 1967-2014 Camaro's Join Date: Jun 2010
Location: Athens, GA and Titusville, FLA
Posts: 341
|
Sounds to me the clips are not all the way in.
|
![]() |
![]() |
![]() |
#8 |
![]() Drives: 22 ZL1 1LE Join Date: Nov 2014
Location: Miami,FL
Posts: 345
|
Where can I buy these? Look awsome on the 1LE!!
|
![]() |
![]() |
![]() |
#9 |
![]() ![]() ![]() ![]() ![]() ![]() ![]() |
__________________
|
![]() |
![]() |
![]() |
#10 |
![]() |
the clips are fully seated. I'm gonna re try using my old clips, they were slightly different. I can't remember how, didn't think it would matter.
|
![]() |
![]() |
![]() |
#11 |
![]() |
Not that noticeable when you are not right above it.
|
![]() |
![]() |
![]() |
#12 |
![]() |
Upper rear portion is flush.
|
![]() |
![]() |
![]() |
#13 |
![]() Drives: '14 Blk SS 2SS/RS 1LE - SOLD :-( Join Date: Apr 2013
Location: Apollo Beach, FL
Posts: 161
|
Mine does that on the passenger door. Not that bad on the driver door.
|
![]() |
![]() |
![]() |
#14 |
Belle Isle
|
Mines stick out slightly further than the stock one as well. I thought it was just me. I like it tho.
__________________
2014 2SS
Credit to xVengeancex28 |
![]() |
![]() |
|
|
![]() |
|
|