|
View our official forum sponsors list. |
|
Thread Tools |
07-30-2009, 01:09 PM | #1 |
Drives: 2016 SS 6 Spd Join Date: Jul 2009
Location: Ohio - www.rpidesigns.com
Posts: 3,185
|
New! Retractable Front License Plate Frame/Holder! Hide your front license plate!
2010 Camaro Retractable Front License Frame
Are you in one of those states where you are required to run a front license plate? If so, this is one accessory you cannot be without. 2010 Camaro retractable front license plate holder. With this retractable plate holder you can hide your ugly front plate within seconds, simply fold it down and stow away. If your on the road just pull it out and flip it up, no more tickets and no more hassle from the authorities. Installation requires just two small holes to be drilled under the front bumper or double sided tape. Adjust up or down in less than 3 seconds! We currently do not have any other pictures on the Camaro except for the one below. Available here: http://rpidesigns.com/shop/item.asp?itemid=1672 Here is what the frame looks like while folded down, mounted on a Corvette. Last edited by RPI Designs; 08-19-2015 at 01:54 PM. |
07-30-2009, 02:06 PM | #2 |
Retarded One-Legged Owl
Drives: 2010 Black Camaro 2SS Join Date: Oct 2008
Location: San Antonio, TX
Posts: 9,745
|
Will this work with the ground effects front lip?
|
07-30-2009, 02:16 PM | #3 |
Thank you Oshawa/St.Cats!
Drives: was 2010 2LT RS 2G1FC1EV4A9103434 Join Date: May 2009
Location: NW NJ
Posts: 3,481
|
See other posts for issues with this on the LS/LT trim.
http://www.camaro5.com/forums/showth...d=1#post739582
__________________
#3434 Born 4-15-2009, Delivered 5-22-2009 BBOMG 2/3/4 - Traded-in 8/31/2019:
|
08-24-2009, 12:05 PM | #4 |
Drives: 2010 black camaro Join Date: Aug 2009
Location: nj
Posts: 290
|
I need one with a motor!!! Anyone out there can post a link!!
|
08-24-2009, 01:44 PM | #5 |
Drives: 2010 Victory Red 2SS/RS M6 Join Date: Jan 2009
Location: Prince George, VA/Lexington, KY
Posts: 586
|
This is dumb...that Helljumper guy did it with a motor. YOU CAN STILL SEE IT when its retracted. 100% waste of time and money.
Not sure how much you can see this one when its down, but on his it looks awful
__________________
|
08-24-2009, 03:16 PM | #6 |
Thank you Oshawa/St.Cats!
Drives: was 2010 2LT RS 2G1FC1EV4A9103434 Join Date: May 2009
Location: NW NJ
Posts: 3,481
|
Here's the link to Altec Products - http://www.altecproducts.com/
Just be mindful of the other posts on this product - if you have a LS/LT the bumper fascia has an angle that doesn't allow the "Show N Go" frame (manual or powered) to lay horizontal. I bought the manual and didn't install it for this reason. I have been working with another member on a bracket but that doesn't look like a solution either. So far I've been running sans front plate with no issues...
__________________
#3434 Born 4-15-2009, Delivered 5-22-2009 BBOMG 2/3/4 - Traded-in 8/31/2019:
|
03-14-2010, 09:13 PM | #7 | |
Drives: '10 Camaro 2SS/RS & Magnum R/T Join Date: Oct 2008
Location: BC, Canada
Posts: 1,520
|
No it will not I am told.
here is mine on youtube!
__________________
SIM Camaro 2010 V8-2SS/RS-A6!!+
|
|
03-15-2010, 06:37 PM | #8 |
Drives: CGM 1LT RS Join Date: Jan 2010
Location: Fayetteville, AR
Posts: 69
|
Does it have to be on the front of the car, I got some suction cups from wal-mart, ones with hooks for bathroom use or whatever, I pulled the hooks out and the suction cups have a small round bit on the non suction side, stuck em through the holes in the plate and suctioned them inside the front windshield on the bottom part, passenger side when I went down to Texas. I am from Texas and it is registered there, although I live in Arkansas, which does not require front ones. I never got hassled with that. Not quite sure what the law states though
|
03-24-2010, 04:25 PM | #9 |
Drives: 2013 Crystal Red Convertible RS Join Date: Jan 2010
Location: Fairview, Texas
Posts: 276
|
just got my retractable front plate holder from you - I have a 2LT - I don't get how I'm supposed to get the thing to work properly with the angle of the bottom of the front bumper (I don't have a problem drilling underneath, but the angle doesn't work). Your instructions (which have mustang on them GRRRRRR ) - talk about washers, but there are none included, and I think I'd have to put like 6 normal washers to get it right - then the SS screws you sent wouldn't be long enough (at least it appears that way). Give me an idea on how to get this to work please . . .
Thanks
__________________
|
01-05-2016, 10:06 AM | #10 |
Drives: 2014 Camaro 2SS RS Join Date: Nov 2015
Location: Tomball Texas
Posts: 9
|
Just ordered. Thx
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FOUND PETITION TO GET RID OF FRONT PLATES | The_Beast_ | USA - California | 90 | 03-29-2012 12:54 AM |
Not having front license plate attached by dealer | New2010CamaroLover | 5th Gen Camaro SS LS LT General Discussions | 154 | 10-07-2010 04:01 PM |
Front License Plate Bracket | blackZbandit | 5th Gen Camaro SS LS LT General Discussions | 76 | 08-17-2009 05:51 PM |
Front license plate | SSCamaro2010 | Cosmetics and Lighting Modification Discussions | 21 | 04-25-2009 04:07 PM |
front license plate | myold88 | 5th Gen Camaro SS LS LT General Discussions | 26 | 02-16-2009 07:09 AM |