Engine bay clean up - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

RaiderSS · 05-04-2015, 07:42 PM

Cleaned up the engine bay after ecs build was done...

Also added:
ZL1 brace, Moroso covers, Taylor 10.4mm wires, spectre filter, E2 can

ActNup NY · 05-04-2015, 08:39 PM

Nicely done

Sent from my iPhone using Tapatalk

canecorso69 · 05-09-2015, 12:19 AM

Are the spacers needed on the strut bar to clear the holley mid rise? That is the mid rise correct. I have the high rise and was thinking about installing the zl1 strut bar but I am not sure about clearance issues.

RaiderSS · 05-11-2015, 09:56 PM

Quote:

Originally Posted by canecorso69

Are the spacers needed on the strut bar to clear the holley mid rise? That is the mid rise correct. I have the high rise and was thinking about installing the zl1 strut bar but I am not sure about clearance issues.

ZL1 brace would actually clear mid rise without spacer (I do have aftermarket motor mounts) I believe it would clear high rise looking at the gap but not sure... I will switch to the hi rise base when I get the cam done hope it all works without further modification

canecorso69 · 05-11-2015, 10:57 PM

Thanks for the info.

KalCorp · 04-19-2016, 10:28 PM

Quote:

Originally Posted by RaiderSS

I do have aftermarket motor mounts

Are these higher or shorter?

So anyone know if the Holley mid rise fit under the cowl as-is?

Slilly20102ss · 04-20-2016, 02:24 AM

Looks killer

Ledzepx · 04-20-2016, 06:07 AM

Nice job! Very clean looking

My 5th · 04-20-2016, 11:07 PM

Quote:

Originally Posted by canecorso69

Are the spacers needed on the strut bar to clear the holley mid rise? That is the mid rise correct. I have the high rise and was thinking about installing the zl1 strut bar but I am not sure about clearance issues.

The spacers are necessary to get the brace to fit the 2010's because the early models strut towers were not dimpled to accept the factory brace.

05-04-2015, 07:42 PM	#1
RaiderSS Drives: 2010 Camaro SS2 DeadBLK Join Date: Nov 2010 Location: Atlanta Posts: 481	Engine bay clean up Cleaned up the engine bay after ecs build was done... Also added: ZL1 brace, Moroso covers, Taylor 10.4mm wires, spectre filter, E2 can Attached Images __________________ RaiderSS - COTW 6/6/11 http://www.camaro5.com/forums/attach...1&d=1312764428

05-04-2015, 08:39 PM	#2
ActNup NY Drives: 2011 1LT Black Camaro Join Date: Feb 2012 Location: Queens, NYC Posts: 2,496 View My Garage	Nicely done Sent from my iPhone using Tapatalk __________________ *The DREAM is free... It's the HUSTLE that is sold seperately*

05-09-2015, 12:19 AM	#3
canecorso69 run ur car not ur mouth Drives: 2013 1LE Join Date: Jul 2013 Location: Middletown, DE; Mayfield, NY Posts: 1,220	Are the spacers needed on the strut bar to clear the holley mid rise? That is the mid rise correct. I have the high rise and was thinking about installing the zl1 strut bar but I am not sure about clearance issues. __________________ TSP headers, cat delete, x-pipe, atak, RPM custom cam and tune, Phfadt 1.25 springs, 15" Carlyle conversion, Nitrous Outlet, Procharger F1A-94, Meth inj

05-11-2015, 10:57 PM	#5
canecorso69 run ur car not ur mouth Drives: 2013 1LE Join Date: Jul 2013 Location: Middletown, DE; Mayfield, NY Posts: 1,220	Thanks for the info. __________________ TSP headers, cat delete, x-pipe, atak, RPM custom cam and tune, Phfadt 1.25 springs, 15" Carlyle conversion, Nitrous Outlet, Procharger F1A-94, Meth inj

04-20-2016, 02:24 AM	#7
Slilly20102ss Drives: 2010 2ss/rs Join Date: Jan 2016 Location: Cincinnati Posts: 147 View My Garage	Looks killer __________________ Roto fab,stainless power works long tube headers,atak cat back exhaust,cat delete and dyno steve custom tune.

04-20-2016, 06:07 AM	#8
Ledzepx Drives: 2010 2SS Camaro 6sp. Join Date: Jan 2012 Location: South Jersey Posts: 639	Nice job! Very clean looking __________________ www.rsconversions.com