You are browsing camaro5 
 |
|
03-14-2017, 08:50 PM
|
#1 |
 Drives: 2011camaross Join Date: Oct 2015
Location: shrevport,la
Posts: 48
|
service stabilatrac light on
I recently did had the intake rod mod and ported throttle body done on my 2011 camaro. After that I put a 1 piece drive shaft in and now the car says to check the stabiltrac. The car also is down on power and not running good. Any ideas. Thanks jerry davis
|
|
|
|
03-14-2017, 09:16 PM
|
#2 |
 Drives: 2010 Camaro SS Join Date: Oct 2013
Location: Saskatoon SK Can. Eh
Posts: 365
|
Give the battery a goog charging.
__________________
 2010 Camaro SS RS, Maggie with 3.4" pulley, 60# injectors, ADM dual fuel pumps, ADM Stage 2 Cam with Brian Tooley springs and pushrods, black CAI intake, Stainless Works long tube headers w/gutted cats, ZL1 Diff w/offset bushings, Pfadt lowering springs, Pfadt sway bars, Pfadt solid sub frame mounts, BMR trailing arms and toe rods, Hurst short throw shifter, Painted on Hugger Orange stripes, Forgestar F14 Piano Black wheels, Nitto NT05 rubber. |
|
|
|
|
03-14-2017, 11:07 PM
|
#3 |
|
WHAT RED LIGHT?!
Drives: 2011 Black Camaro 2SS/RS M6 Join Date: Apr 2011
Location: Miami, Florida
Posts: 1,115
|
Try to get some codes
__________________
2011 2SS/RS M6 BLACK - VARARAM NO TUNE INTAKE, MODDED AND PORTED TB, PORTED INTAKE MANIFOLD, VITESSE THROTTLE CONTROLLER, DOUG THORLEY LT'S, CATLESS, X-PIPE, 25" STAINLESS WORKS RETRO CHAMBERED MUFFLERS, CUSTOM 2.5" MANDREL BENT EXHAUST, RICHMOND 4.10 GEARS, CUSTOM CAM (231/242 @ 114LSA), MUSTANG DYNO TUNED BY TORQ, 20% CERAMIC TINTS, EIBACH PROKIT SPRINGS 1" DROP, HAWK PERFORMANCE CERAMIC BRAKES, NITTO INVO TIRES, HYDROCARBON TAIL LIGHT AND FOG LIGHT BEZELS BY EMBLEMPROS, METRA DASH KIT, JVC KW-AV71BT, PHOENIX GOLD iAMP GM1, PASSPORT QI45 - 450 RWHP 415 RWTQ
 |
|
|
|
|
03-15-2017, 08:12 PM
|
#4 |
 Drives: 2013 1ss Join Date: Jul 2012
Location: WI.
Posts: 569
|
I have had dirty throttle body and maf sensor cause the computer to cause it to run terrible like it was in limp mode or reduced power. In relation to the 1 piece driveshaft, I installed one and I get a lot of stabilitrack warning at light throttle steady cruise. The 1 pc shafts removed the rubber isolator causing the driveline lash to throw the code. Still trying to figure a way out of that one.
|
|
|
|
|
03-16-2017, 08:29 AM
|
#5 | |
|
Drives: 2011camaross Join Date: Oct 2015
Location: shrevport,la
Posts: 48
|
Quote:
|
|
|
|
|
|
03-16-2017, 09:26 AM
|
#6 | |
|
My Dream Car
Drives: 2011 SIM LS3 1SS Join Date: Jul 2009
Location: staten island
Posts: 1,534
|
Quote:
this maybe the issue, as my battery started to go, I would get the service stabilitrac light . Plus a few other issues. as soon as I changed the battery they stopped happening
__________________
CAI intake/ADM Scoop/Stainless Power Headers/Dynatech cat back exhaust/Vitesse Throttle Control/ Ported Throttle Body/QTP Electric Cutouts/ 3.91 gears and janetty rear posi/ Tuned by Janetty racing
|
|
|
|
|
|
03-16-2017, 07:20 PM
|
#7 |
|
Drives: 2011camaross Join Date: Oct 2015
Location: shrevport,la
Posts: 48
|
I pulled some codes out of it today they were p0122 p0123. P0223. P2135. These are all throttle postion codes. I charged the battery ans the stabiktack light went off. I also eraised the codes car runs fine now. Trying to figure out if I need to replace the throttle postion senser. What are your thoughts. Thanks jerry davis
|
|
|
|
|
03-16-2017, 09:02 PM
|
#8 |
Drives: 2013 Black SS Join Date: Apr 2016
Location: Ky
Posts: 6
|
I have never had tps problems, but when trying to tune after my lsa swap, the stabilitrac light was a constant problem. I Tracked it all back to a bad connection at the MAP sensor splice. Connections were good but I cut it all apart and re soldered everything. This took care of it, but I was able to catch it while data logging.
Last edited by drgrcr32; 03-16-2017 at 09:54 PM. Reason: Posted wrong component. |
|
|
|
|
03-16-2017, 09:05 PM
|
#9 | |
|
Drives: Camaro Justice Join Date: Jun 2007
Location: Virginia
Posts: 20,171
|
Quote:
|
|
|
|
|
|
|
|
|
 |
|
|
