06-21-2017, 02:26 AM | #1 |
Lingenfelter Reservoir
Does anyone know what cold air intakes will fit with the Lingenfelter Reservoir other than their own one , or if the stock airborne fits with it ?
http://www.lingenfelter.com/product/...l#.WUofbGh5af0
__________________
2012 ZL1 A6
Pulley upgrade CAI cold air Rotofab coolant reservoir 14.3 psi 513rwhp |
|
06-21-2017, 06:43 AM | #2 |
Drives: 2013-ZL1, 69-Z28, 71-CHEVELLE SS Join Date: Oct 2016
Location: South Jersey
Posts: 268
|
I have Cold air inductions and it fit but it is tight., had to modify slightly.
__________________
2017 C7 Z06
2013-ZL1 2017 HELLCAT SOLD 2019 HELLCAT REDEYE WB 69-Z28, LSA SWAP, T56 MAGNUM 71-CHEVELLE SS, 496 STROKER TH400 |
06-21-2017, 08:52 AM | #3 |
Drives: 2015 ZL1 Blue Velvet Metallic Join Date: Mar 2015
Location: Melbourne, FL
Posts: 720
|
I have Roto-Fab which is a perfect fit, which it should be since RF makes that reservoir for Lingenfelter.
__________________
Roto-Fab CAI, ARH LT, SW 3" catback, JRE tune, Elite-2 CC, VMAX TB, Big Gulp, WW II relo, Lingenfelter S/C reservoir
|
06-21-2017, 09:54 AM | #4 |
Drives: 2013 Triple Black ZL1 / 2006 TB SS Join Date: Feb 2011
Location: MN
Posts: 2,250
|
I previously ran the K&N and now run the JLT without a problem.
|
06-21-2017, 07:04 PM | #5 |
Do you have a pic, and what did you have to modify ?
__________________
2012 ZL1 A6
Pulley upgrade CAI cold air Rotofab coolant reservoir 14.3 psi 513rwhp |
|
06-21-2017, 08:22 PM | #6 |
Drives: 2013-ZL1, 69-Z28, 71-CHEVELLE SS Join Date: Oct 2016
Location: South Jersey
Posts: 268
|
There is a stud adapter in the kit, I had to make an offset adapter. Check out these instructions and you will see what im talking about, I used the expoxy putty stick to make my offset adapter by filling the hole in bottom of resevoir with the epoxy and slipping it over the stud adapter and let it dry, no need to put the nut on. http://www.jannettyracing.com/Instal...structions.pdf
__________________
2017 C7 Z06
2013-ZL1 2017 HELLCAT SOLD 2019 HELLCAT REDEYE WB 69-Z28, LSA SWAP, T56 MAGNUM 71-CHEVELLE SS, 496 STROKER TH400 |
06-22-2017, 01:43 AM | #7 | |
Quote:
__________________
2012 ZL1 A6
Pulley upgrade CAI cold air Rotofab coolant reservoir 14.3 psi 513rwhp |
||
06-22-2017, 12:14 PM | #8 |
Drives: 2014 ZL1 Join Date: Sep 2012
Location: West Virginia
Posts: 591
|
The adaptor stud is for the ligenfelter reservoir. It is made by rotofab, and uses the same reservoir as their windshield washer relocate. I have the same setup on my car
|
06-22-2017, 12:17 PM | #9 |
Drives: 2014 ZL1 Join Date: Sep 2012
Location: West Virginia
Posts: 591
|
Here is the only picture I have right now, but I can take a better one if you need.
|
06-22-2017, 05:27 PM | #10 |
OK thanks, so a relatively easy job ?
__________________
2012 ZL1 A6
Pulley upgrade CAI cold air Rotofab coolant reservoir 14.3 psi 513rwhp |
|
06-23-2017, 09:31 PM | #11 |
Drives: 2014 ZL1 Join Date: Sep 2012
Location: West Virginia
Posts: 591
|
Yeah, it shouldn't be very difficult. I had RDP (dyno Steve) install mine when I was getting some other work done.
|
|
|
|
|