Argenteus Lives: Dragoneye's 1LE

[Mr. Wyndham]

Originally Posted by DGthe3

The solution, so I've heard, is to keep the plate on your dash and in the event that you get pulled over just say that you were just on your way to get a plate holder. Not that its of much help now ... lol

In all honesty I HAVE been conceiving a solution so that I can comply with the law...but I shat the bed when I opened the glovebox to get out my registration and he saw the plate in there....I don't want it to scratch up my dash!!!!

Originally Posted by speedster

Oh, C'mon... You know you love Beefalo...
Hey, you had less than 10 feet of snow this year. That must be some kind of record.

Yeah...It's called a break from the normal crap...praying it happens again, this year...that'll mean I get to keep the car out of storage well into November!!!

[The Stig]

Ouch. Sorry to hear Joe. CFD came up with a solution that incorporates the plate into the lower grills

[Mr. Wyndham]

You're going to link me, like a good friend....right?

[The Stig]

Yea give me a bit. I'm on my phone.

[Mr. Wyndham]

That's fine...only kidding!

[The Stig]

http://www.camaro5.com/forums/showthread.php?t=170726

[JoeP@TeamBeckyD]

Originally Posted by stieger

Ouch. Sorry to hear Joe. CFD came up with a solution that incorporates the plate into the lower grills

There are solutions available...


Sorry Joe...
:(

[Mr. Wyndham]

Originally Posted by stieger

http://www.camaro5.com/forums/showthread.php?t=170726

hmmm...interesting...I don't think that will work quite the same on my car, though...and I'm looking for something much more temporary that I can take on and off with ease for shows/racing...

[The Stig]

Suction cups? I mean if a GoPro can hang on I'm sure your plate could

[Bad@ssCamaro]

Forum member DBLCHBY did this for his:

http://www.camaro5.com/forums/showth...hlight=dblchby

[Mr. Wyndham]

Originally Posted by Bad@ssCamaro

Forum member DBLCHBY did this for his:

http://www.camaro5.com/forums/showth...hlight=dblchby

Yeah - that was a favorite of mine until I learned what went on underneath for airflow...not to mention the already low clearance....

Suction cups might work....only problem being marring the paint in the long-term...GoPros aren't attached for months on end.

[Bad@ssCamaro]

Originally Posted by Dragoneye

Yeah - that was a favorite of mine until I learned what went on underneath for airflow...not to mention the already low clearance....

Suction cups might work....only problem being marring the paint in the long-term...GoPros aren't attached for months on end.

what about a frame that attaches from underneath the front lip that sits on a corner of the bottom front grill? You know, like an L-bracket type setup. I'm sure someone on this forum can make something up.

[Mr. Wyndham]

Originally Posted by Bad@ssCamaro

what about a frame that attaches from underneath the front lip that sits on a corner of the bottom front grill? You know, like an L-bracket type setup. I'm sure someone on this forum can make something up.

Maybe....I was, at first, thinking of magnets...but Gtahvit blew that out of the water....now I'm thinking to cover the edges of the plate in rubber...and bolting it to a plate on the inner-center of the lower grille...also Gtahvit's idea...

[Bad@ssCamaro]

Originally Posted by Dragoneye

Maybe....I was, at first, thinking of magnets...but Gtahvit blew that out of the water....now I'm thinking to cover the edges of the plate in rubber...and bolting it to a plate on the inner-center of the lower grille...also Gtahvit's idea...

I think having it mounted the way I suggested would at least allow air to flow around it and not be as restrictive as GTA's idea...my 2 cents.