Stock LSX376-B15, anyway to increase compression ratio - Page 9 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

2SS45th · 06-16-2013, 09:38 AM

Then you're going to need the 10 rib setup, because I'm only getting 13 without the upgrades.

10aSSee D · 06-16-2013, 09:42 AM

Quote:

Originally Posted by Fiftydriver

Who said anything about running 15-18 lbs of boost. THere is likely no way in hell that my maggie would be able to produce that level of boost without all the upgrades and I am not going with those. THis is a street car and I am looking for 10-12 boost range max.

Gotcha, just assumed I guess you would running more boost on a built motor. Cool build you got going, I wish mine was under way...

ADM PERFORMANCE · 06-16-2013, 10:02 AM

Quote:

Originally Posted by 10aSSee D

Gotcha, just assumed I guess you would running more boost on a built motor. Cool build you got going, I wish mine was under way...

I have 2-417 shortbloks in stock.

1 new block , new callies crank,new callies rods,new manley 18cc dish 4.070 pistons.fully balanced and blueprinted tested combo is on our website in our texas mile cadi.

1 used block , new manley crank,new manley rods,new mahle 28cc dish 4.075 pistons,all new bearings,fully balanced and bluepriinted

Just waiting on you

Unavowed · 06-16-2013, 02:00 PM

In Waterbury now, but nothing is open on Sunday...

Supercharged SS · 06-16-2013, 02:04 PM

Quote:

Originally Posted by Unavowed

In Waterbury now, but nothing is open on Sunday...

Unavowed · 06-16-2013, 04:57 PM

Came up for a wedding. Drove by the Mecca of speed. Not a soul in sight. Evidence of a few burnouts though. You can't swing a dead cat without hitting a Dunkin Doughnuts though. I may stop in Sandy Hook on my way home tomorrow to pay my respects. Not sure what is appropriate though.

Supercharged SS · 06-16-2013, 05:32 PM

Quote:

Originally Posted by Unavowed

Came up for a wedding. Drove by the Mecca of speed. Not a soul in sight. Evidence of a few burnouts though. You can't swing a dead cat without hitting a Dunkin Doughnuts though. I may stop in Sandy Hook on my way home tomorrow to pay my respects. Not sure what is appropriate though.

Ah, that makes sense now. Could've been waterbury vt. Nothing at JRE on a sunday. Tomorrow it all starts up again.

No harm in driving through Sandy Hook. Really not much to see now though.

10aSSee D · 06-16-2013, 07:20 PM

Quote:

Originally Posted by ADM PERFORMANCE

I have 2-417 shortbloks in stock.

1 new block , new callies crank,new callies rods,new manley 18cc dish 4.070 pistons.fully balanced and blueprinted tested combo is on our website in our texas mile cadi.

1 used block , new manley crank,new manley rods,new mahle 28cc dish 4.075 pistons,all new bearings,fully balanced and bluepriinted

Just waiting on you

That sounds good, I keep getting little surprises like my wife telling me we have another kiddie on the way

I have managed to get a street slayer clutch on the way to bring with me for when you do the build, hopefully sooner than later

Fiftydriver · 06-16-2013, 10:29 PM

Quote:

Originally Posted by 2SS45th

Then you're going to need the 10 rib setup, because I'm only getting 13 without the upgrades.

Only looking for 10-12 lbs boost so if anything the 8 rib should be fine. Hoping anyway.

Fiftydriver · 06-16-2013, 10:30 PM

Quote:

Originally Posted by ADM PERFORMANCE

I have 2-417 shortbloks in stock.

1 new block , new callies crank,new callies rods,new manley 18cc dish 4.070 pistons.fully balanced and blueprinted tested combo is on our website in our texas mile cadi.

1 used block , new manley crank,new manley rods,new mahle 28cc dish 4.075 pistons,all new bearings,fully balanced and bluepriinted

Just waiting on you

Just in the planning stages now so not ready to pull the trigger and say GO right now. I bet both these motors would be real screamers!!!

Unavowed · 06-17-2013, 12:00 AM

Quote:

Originally Posted by ADM PERFORMANCE

I have 2-417 shortbloks in stock.

1 new block , new callies crank,new callies rods,new manley 18cc dish 4.070 pistons.fully balanced and blueprinted tested combo is on our website in our texas mile cadi.

1 used block , new manley crank,new manley rods,new mahle 28cc dish 4.075 pistons,all new bearings,fully balanced and bluepriinted

Just waiting on you

So 417ci @ 10.3:1 + TVS2300 @ 12psi = ?? rwhp?

Supercharged SS · 06-17-2013, 05:32 AM

Quote:

Originally Posted by VanquisherSS

Hold your horses, I'll be posting shortly

.

. Test and tune at Atco Sunday I might give it another go with the juice. I think the stock clutch is about had it though.

ADM PERFORMANCE · 06-17-2013, 08:14 AM

Quote:

Originally Posted by Unavowed

So 417ci @ 10.3:1 + TVS2300 @ 12psi = ?? rwhp?

Depends on heads and cam and other mods

Unavowed · 06-17-2013, 10:03 PM

Quote:

Originally Posted by ADM PERFORMANCE

Depends on heads and cam and other mods

Your worked LS3's and a GT-9, long tubes, pump 93, A6.

06-16-2013, 09:38 AM	#113
2SS45th Drives: 11 Seconds or Faster Join Date: May 2012 Location: Arvada, Colorado Posts: 2,797 View My Garage	Then you're going to need the 10 rib setup, because I'm only getting 13 without the upgrades. __________________ I Ain't About That Stock Life.

06-16-2013, 02:00 PM	#116
Unavowed Drives: Twin turbo G8 GXP Join Date: Dec 2012 Location: MD Posts: 454	In Waterbury now, but nothing is open on Sunday...

06-16-2013, 04:57 PM	#118
Unavowed Drives: Twin turbo G8 GXP Join Date: Dec 2012 Location: MD Posts: 454	Came up for a wedding. Drove by the Mecca of speed. Not a soul in sight. Evidence of a few burnouts though. You can't swing a dead cat without hitting a Dunkin Doughnuts though. I may stop in Sandy Hook on my way home tomorrow to pay my respects. Not sure what is appropriate though.