08-06-2011, 11:21 AM | #1 |
Drives: 2013 2LT/RS Summit White Join Date: Feb 2011
Location: NY
Posts: 1,283
|
Vararam + RX Catch Can/Breather questions
I'm going to do the install today or tomorrow, driver's side.
If you have this setup, what did you do with the Vararam breather? Leave it on? Any harm or benefit on having the Vararam breather and the RX breather? Plug the line? If you plugged the line, what did you use and how much hose did you leave? Help = greatly appreciated. |
08-06-2011, 11:54 AM | #2 |
Love me some Tacos
|
Remove the Vararam breather and plug it with one of these http://www.camaro5.com/forums/showpo...6&postcount=44
this can be purchased from lowes. Any harm, well I am not Tracy or SC2150 (same person). I think you would cap it and use the oil cap filter. I placed my RX Catch can on the driver side just easier to get to. |
08-06-2011, 03:00 PM | #3 |
Drives: 2010 2SS/RS Coupe Join Date: Feb 2011
Location: Peoria, IL
Posts: 330
|
Here is what I did and was recommended by Tracey. Basic answer is toss the VR breather to the side and plug the line. Just put the breather and catch can on this morning too.
Here are a few installed pics: First pull out the whole clean side assembly: There should be a little 45' fitting on the back of the engine: Got this little plug at home depot, was like $1.75: Take off the last little black rubber piece of the assembly and put the plug in: Install the plugged rubber piece back on the engine:
__________________
2010 CGM 2SS/RS
Last edited by baup5f; 02-22-2012 at 02:10 PM. |
08-06-2011, 03:10 PM | #4 |
Drives: 2010 2SS/RS Coupe Join Date: Feb 2011
Location: Peoria, IL
Posts: 330
|
One more thing, I didn't route my catch can hoses very well so my engine cover doesn't really snap on very well. Plus the edge of of the engine cover sits tight on the top of the catch can which could also account for it not snapping back in easily.
__________________
2010 CGM 2SS/RS
|
08-06-2011, 03:38 PM | #5 |
Love me some Tacos
|
I would just mount it on the driver side. That is if you dont have something else there. I asked for the driver bracket and Tracy was nice enough to send one. RX is the best!!!!
|
08-06-2011, 03:51 PM | #6 |
Tracy (RX) did mine for me when I drove down there and pulled my Vararam breather off then capped it. As for the engine cover, the day before yesterday I got tired of pulling it off and back on so I decided to ditch it. It is not only useless (other than for show) but it holds hot air in. Very bad design by GM... When I get my TB from Tracy (who knows when) I'll pay extra to have the whole TB painted. That cover will be going into the garbage. lol
|
|
08-06-2011, 04:24 PM | #7 |
Drives: 2011 Camaro 1lt rs auto 4-9-11 Join Date: Apr 2009
Location: NY Long Island
Posts: 754
|
i got both breathers in now,dont have anything to plug it with right now,any harm that can happen?
__________________
|
08-06-2011, 04:24 PM | #8 |
Drives: 2010 2SS/RS Coupe Join Date: Feb 2011
Location: Peoria, IL
Posts: 330
|
I was originally going to, but decided on that location. If for any reason I need to put the stock intake back on, the drivers side mount would be a pain to try and relocate, imo.
__________________
2010 CGM 2SS/RS
|
08-06-2011, 04:26 PM | #9 | |
Drives: 2010 2SS/RS Coupe Join Date: Feb 2011
Location: Peoria, IL
Posts: 330
|
Quote:
__________________
2010 CGM 2SS/RS
|
|
08-06-2011, 04:28 PM | #10 |
Drives: 2010 2SS/RS Coupe Join Date: Feb 2011
Location: Peoria, IL
Posts: 330
|
Just redundant and probably letting a little too much air in. Probably won't hurt it too much, but your fuel trims won't be able to completely set in until you find something to plug it.
__________________
2010 CGM 2SS/RS
|
08-06-2011, 04:55 PM | #11 |
Drives: 2011 Camaro 1lt rs auto 4-9-11 Join Date: Apr 2009
Location: NY Long Island
Posts: 754
|
hmmmm i will take it out then thanks
wish i knew the vararam came with with a breather would of saved me $40
__________________
|
08-06-2011, 05:00 PM | #12 | |
Drives: 2010 2SS/RS Coupe Join Date: Feb 2011
Location: Peoria, IL
Posts: 330
|
Quote:
Going with just the VR breather and put the regular oil cap on for right now shouldn't be too bad, but I would still try to use the VR breather only whenever you get a chance to head to the hardware store.
__________________
2010 CGM 2SS/RS
|
|
08-06-2011, 05:35 PM | #13 |
Drives: 2013 2LT/RS Summit White Join Date: Feb 2011
Location: NY
Posts: 1,283
|
Thx for everyone's input. I'll have to to hit Home Depot or Lowe's tomorrow morning.
|
08-06-2011, 08:09 PM | #14 | |
|
Quote:
You could always do a cool custom job on yours rather than just ditching it. Several members have posted threads on their custom covers.
__________________
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
V6 Questions I'd Like Answered | The_Blur | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 36 | 07-14-2012 10:44 AM |
****CNC BILLET OIL CATCH CAN OPTIONS**** | DREV LSX | V8 Bolt-Ons & Tunes | 57 | 03-08-2012 07:46 PM |
Elite Engineering Catch Cans Now Available At APEX Motorsports! Multiple Colors! | Apex Motorsports | V8 Bolt-Ons & Tunes | 136 | 06-30-2011 05:24 AM |
RX Catch can install questions | mrh923 | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 18 | 04-02-2011 09:10 PM |