Blackout rear kit and badge - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

silentdoom · 10-28-2010, 09:49 PM

The piece of vinyl that you can buy that's black and goes below the spoiler... Do u think if you put that on the car you can just take the badge and leave it off no problems? Just wondering
Thanks

LoneStar · 10-28-2010, 09:53 PM

If the blackout in this picture is what you are talking about, then yes you can take off the emblem without a problem. Since you have a 2011, there are no holes in the trunk under the emblem.

ORANGE U NV · 10-28-2010, 10:20 PM

BTW, 2010's has 2 holes behind the bowtie.

Shadowshawn · 10-28-2010, 10:21 PM

since you have a 2011 you should be able to do it with no problems. People like me who have the 2010's can't do it because than we'd be left with 2 holes in the trunk.

JerseyMonte · 10-29-2010, 07:27 AM

I got this fill in panel on Ebay about a year ago
I think it was about 20 or 30 bucks,
it is cut to fit around the bowtie
it shrunk a little on the ends but not too noticable
I don't know if it is still available or not.

CamaroCowboy · 10-29-2010, 07:46 AM

I had the holes and just used the blackout vinyl over the holes. Havn't had any problems

aldaron327 · 10-29-2010, 09:35 AM

Quote:

Originally Posted by CamaroCowboy

I had the holes and just used the blackout vinyl over the holes. Havn't had any problems

Me either. My car's whole tail panel is blacked out and the vinyl covered the holes just fine. Then I put an "old-school" SS emblem over the top of that and you can't see even the vaguest outline of the holes.

CamaroCowboy · 10-29-2010, 09:53 AM

aldaron327 · 10-29-2010, 09:57 AM

Quote:

Originally Posted by CamaroCowboy

Murph0408 · 10-29-2010, 10:09 AM

Quote:

Originally Posted by CamaroCowboy

wow. i'm surprised by how good this looks, definitely helps make yours unique, good job.

Ironheadspearo · 10-29-2010, 10:12 AM

if you want to remove that emblem you can use strong fishing line or string, I recommend some gloves as well. you run the string behind the emblem till you basically cut through the 3m double sides stick tape. once removed you have the fun of getting the remaining tape off which might take you 30 minutes, then finish it off with goof off and then wax. i did mine but honestly wouldnt offer to do one for anyone else.

CamaroCowboy · 10-29-2010, 10:49 AM

Quote:

Originally Posted by Murph0408

wow. i'm surprised by how good this looks, definitely helps make yours unique, good job.

thanks man, I appreciate that.

INTIMIDAT3R · 10-29-2010, 11:03 AM

Just do like I did and have them cut around it. It looks good and right now I'm just waiting on some vinyl cut-outs for the bowties.

silentdoom · 10-29-2010, 01:56 PM

So is fishing line the best way to remove the badge. Seems soo scary

10-28-2010, 09:49 PM	#1
silentdoom Silentdoom.com Drives: 11' Synergy SS/RS Join Date: Sep 2010 Location: Saint Charles, MO Posts: 154	Blackout rear kit and badge The piece of vinyl that you can buy that's black and goes below the spoiler... Do u think if you put that on the car you can just take the badge and leave it off no problems? Just wondering Thanks __________________ Modern day hair metal! Silentdoom.com

10-28-2010, 09:53 PM	#2
LoneStar Drives: 2011 IOM Camaro Join Date: Jul 2010 Location: Texas Posts: 3,446	If the blackout in this picture is what you are talking about, then yes you can take off the emblem without a problem. Since you have a 2011, there are no holes in the trunk under the emblem. Attached Images

10-28-2010, 10:20 PM	#3
ORANGE U NV Drives: The Wife Crazy Join Date: Jul 2009 Location: TAMPA BAY Posts: 550	BTW, 2010's has 2 holes behind the bowtie. __________________ "God is great, beer is good and people are crazy" 2010 2SS IOM/IOM L99 Black Rally Stripes, Polished Wheels, Loudmouth II, Rotofab CAI, IOM Heritage Grille,Tune by Jeremy Formato (Fasterproms Tuning).

10-28-2010, 10:21 PM	#4
Shadowshawn Drives: 2010 SW 2SS/RS LS3 M6 Join Date: Oct 2010 Location: Rowland Heights,California Posts: 113	since you have a 2011 you should be able to do it with no problems. People like me who have the 2010's can't do it because than we'd be left with 2 holes in the trunk. __________________

10-29-2010, 07:27 AM	#5
JerseyMonte Drives: 1972 Z28 Join Date: Mar 2009 Location: Southern New Jersey Posts: 346	Magnetic black insert I got this fill in panel on Ebay about a year ago I think it was about 20 or 30 bucks, it is cut to fit around the bowtie it shrunk a little on the ends but not too noticable I don't know if it is still available or not.

10-29-2010, 07:46 AM	#6
CamaroCowboy Drives: 2013 Chevy Truck Join Date: Mar 2010 Location: Copperas Cove, Texas Posts: 1,782 View My Garage	I had the holes and just used the blackout vinyl over the holes. Havn't had any problems __________________ Texas speed LT Headers and High Flow Cats, Magnaflow 3 inch cat-back Exhaust, SNL V2 Comp CAM, Texas Speed Underdrive Pully, G5CR CAI, Hurst Short Throw Shifter, JetFlo Mass Air Sensor, Custom Grill, Amber AAC Headlight and Fog Light Halo, Amber footwell Lighting, Amber under hood lighting, RK Sport Ram Air /Heat Extractor Hood and ADM Racing Scoop. 447.9 RWHP 428 TQ My car is exactly that, No one has to like it but me!

10-29-2010, 09:53 AM	#8
CamaroCowboy Drives: 2013 Chevy Truck Join Date: Mar 2010 Location: Copperas Cove, Texas Posts: 1,782 View My Garage	__________________ Texas speed LT Headers and High Flow Cats, Magnaflow 3 inch cat-back Exhaust, SNL V2 Comp CAM, Texas Speed Underdrive Pully, G5CR CAI, Hurst Short Throw Shifter, JetFlo Mass Air Sensor, Custom Grill, Amber AAC Headlight and Fog Light Halo, Amber footwell Lighting, Amber under hood lighting, RK Sport Ram Air /Heat Extractor Hood and ADM Racing Scoop. 447.9 RWHP 428 TQ My car is exactly that, No one has to like it but me!

10-29-2010, 10:12 AM	#11
Ironheadspearo ride the pain train Drives: 2011 1LT RS, 1998 fxstc HD Join Date: Jun 2010 Location: Daytona Beach Posts: 2,047	if you want to remove that emblem you can use strong fishing line or string, I recommend some gloves as well. you run the string behind the emblem till you basically cut through the 3m double sides stick tape. once removed you have the fun of getting the remaining tape off which might take you 30 minutes, then finish it off with goof off and then wax. i did mine but honestly wouldnt offer to do one for anyone else. __________________ PAIN is temporary, PRIDE is forever......RACE HARD

10-29-2010, 11:03 AM	#13
INTIMIDAT3R Account Suspended Drives: '11 2SS/RS L99, '12 2LS LFX Join Date: Jul 2010 Location: Malmac A.U.N. Posts: 2,122 View My Garage	Just do like I did and have them cut around it. It looks good and right now I'm just waiting on some vinyl cut-outs for the bowties. Last edited by INTIMIDAT3R; 10-29-2010 at 04:07 PM.

10-29-2010, 01:56 PM	#14
silentdoom Silentdoom.com Drives: 11' Synergy SS/RS Join Date: Sep 2010 Location: Saint Charles, MO Posts: 154	So is fishing line the best way to remove the badge. Seems soo scary __________________ Modern day hair metal! Silentdoom.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY RS badge kit for 2lt Camaro	Camaro Freak	Camaro DIY & HOW-TO instructions & discussions	4	08-19-2013 03:00 PM
Modifying for " Dummies"	Dr Jkel	Tuning / Diagnostics -- engine and transmission	209	06-17-2012 11:24 PM
DRESDEN® - Complete Grille Kit	CARiD	Exterior Parts & Accessories	0	08-20-2010 12:41 AM
More Challenger Information (drivetrain)	The_Stache	General Automotive + Other Cars Discussion	47	04-19-2009 06:26 PM
1SS standard equipment and options	Tran	Wiki	1	11-05-2008 02:34 PM