03-02-2015, 05:06 PM | #1 |
Drives: 2011 Camaro 3.6L V6 Join Date: Sep 2014
Location: South Georgia
Posts: 153
|
Putting on custom Badges...
So I got some of the old school Camaro badges and am in the process of pondering how exactly I'm going to get these things to stay on the car...
I've seen this done by a couple of other members and for the life of me can't find them now to take notes on their process... I'm figuring that I'll have to dremel off the posts on the back (that would have ordinarily pushed into holes in the fender which I will not be doing) and then find an extremely strong adhesive of some kind... Any suggestions? Thanks for your time and consideration!
__________________
Check out my Build Thread! Feedback is Welcome and Appreciated! |
03-02-2015, 05:08 PM | #2 |
Drives: 2011 Camaro 3.6L V6 Join Date: Sep 2014
Location: South Georgia
Posts: 153
|
__________________
Check out my Build Thread! Feedback is Welcome and Appreciated! |
03-03-2015, 08:20 AM | #3 |
Drives: 2014 Camaro 2LT/RS Join Date: Jun 2014
Location: Perry, Ga
Posts: 23
|
I bought a set from Emblempros.com. His don't have the post on the back but are held on by double sided tape. Nice badges by the way. Good luck.
|
03-03-2015, 08:30 AM | #4 |
PaPa Smurf
|
3M makes some very good very strong adhesive for this. Lowe's or the depot should carry it. But I would see what those are worth to a collector or someone doing a resto project and make a couple $$ and put the emblem pro's on there.
__________________
2022 Rapid Blue SS 1LE
|
03-03-2015, 08:43 AM | #5 |
Drives: 2011 Camaro 3.6L V6 Join Date: Sep 2014
Location: South Georgia
Posts: 153
|
I'll go check out Lowe's today and see what they have... BTW these are stainless steel.. not too heavy but noticeably heavier than the plastic ones which is why I'm paranoid about them coming off!
__________________
Check out my Build Thread! Feedback is Welcome and Appreciated! |
03-03-2015, 08:44 AM | #6 |
Drives: 2011 Camaro 3.6L V6 Join Date: Sep 2014
Location: South Georgia
Posts: 153
|
I'll also check out emblem pros and see about pricing
__________________
Check out my Build Thread! Feedback is Welcome and Appreciated! |
03-03-2015, 08:45 AM | #7 |
PaPa Smurf
|
That's what I would do. I don't know how rare or common those stainless ones are. Sometimes those things dissappear from fenders.
__________________
2022 Rapid Blue SS 1LE
|
03-03-2015, 09:20 AM | #8 |
Car Enthusiast
Drives: 2010 Rally Yellow Camaro 2SS A/T Join Date: Dec 2010
Location: Keller, Texas
Posts: 760
|
i would also go with them emblempros ones since they come ready to install.
__________________
2010 Rally Yellow 2SS/RS
Performance Upgrades: Custom Flowmaster X system Exhaust Audio Upgrades: Too much to write down. Visit http://www.camaro5.com/forums/showthread.php?t=206016 |
03-03-2015, 10:23 AM | #9 |
Drives: 2011 Camaro 3.6L V6 Join Date: Sep 2014
Location: South Georgia
Posts: 153
|
Do they come with the 3m double sided tape? or whatever it is they use? If so I'll probably go that route if they are the same size and use these badboys as decoration around the "man cave"
__________________
Check out my Build Thread! Feedback is Welcome and Appreciated! |
03-03-2015, 10:27 AM | #10 |
PaPa Smurf
|
They come ready to install. I've been looking at them also.
__________________
2022 Rapid Blue SS 1LE
|
03-03-2015, 06:58 PM | #11 |
Drives: 2010 2ss 6 speed Join Date: Apr 2011
Location: NEW BRUNSWICK CANADA
Posts: 328
|
did this a year ago
|
|
|
|
|