Cradle torque specs?? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Irace16 · 06-01-2015, 11:31 PM

Anyone know the front and rear cradle torque specs? I dropped the rear to install toe rods and dropped the front door a chassis brace. I know they were tight as hell when I removed the bolts and I'm sure I don't have them that tight ,just looking for the number. Thanks

Orange 2010 Camaro · 06-02-2015, 11:15 AM

As a last resort, go to your local Chevrolet dealer & ask for the parts & or Service manager.

Tell him or her what your doing with your car, & let them know that you want a safe car to drive after the installation of the parts & he or she will most likely run you a copy of the areas of the car that you need the Torque values for.

That is what I did when installing my new Ride Tech Coil Over suspension & they were glad to help me.

All The Best,

Orange 2010 Camaro

Ventmaster · 06-02-2015, 11:29 AM

Toe link to inner to subframe adjuster 85lbft
Toe link to knuckle assembly 103lbft.
Front and Back cradle (rear subframe) bolts to body 74lbft, then +120degrees.

Subframe bolts front- front bolts 118lbft, rear177lbft

JusticePete · 06-02-2015, 11:38 AM

Most of what you need can be found on the JPSS website. http://www.jpssonline.com/#/the-book...n-2010-camaro/

This is a direct link to the suspension and alignment section http://www.jpssonline.com/the-book-f...-2010-camaro-2

Irace16 · 06-02-2015, 07:00 PM

Thanks everyone! I'll get the torque wrench out tonight

06-01-2015, 11:31 PM	#1
Irace16 Drives: 2010 1SS RS M6 Join Date: Jan 2015 Location: Appleton, Wisconsin Posts: 521	Cradle torque specs?? Anyone know the front and rear cradle torque specs? I dropped the rear to install toe rods and dropped the front door a chassis brace. I know they were tight as hell when I removed the bolts and I'm sure I don't have them that tight ,just looking for the number. Thanks __________________ Vararam intake, gmpp exhaust, borla stainless long tubes, cat less, jannetty tune, bmr lowering springs, heritage grill , smoked lenses

06-02-2015, 07:00 PM	#5
Irace16 Drives: 2010 1SS RS M6 Join Date: Jan 2015 Location: Appleton, Wisconsin Posts: 521	Thanks everyone! I'll get the torque wrench out tonight __________________ Vararam intake, gmpp exhaust, borla stainless long tubes, cat less, jannetty tune, bmr lowering springs, heritage grill , smoked lenses

06-02-2015, 11:15 AM	#2
Orange 2010 Camaro Drives: 2010 2SS/RS Camaro Join Date: Aug 2014 Location: United States Posts: 268	As a last resort, go to your local Chevrolet dealer & ask for the parts & or Service manager. Tell him or her what your doing with your car, & let them know that you want a safe car to drive after the installation of the parts & he or she will most likely run you a copy of the areas of the car that you need the Torque values for. That is what I did when installing my new Ride Tech Coil Over suspension & they were glad to help me. All The Best, Orange 2010 Camaro

06-02-2015, 11:29 AM	#3
Ventmaster Drives: 2017 1SS 6spd Join Date: Jan 2011 Location: Utah Posts: 3,024	Toe link to inner to subframe adjuster 85lbft Toe link to knuckle assembly 103lbft. Front and Back cradle (rear subframe) bolts to body 74lbft, then +120degrees. Subframe bolts front- front bolts 118lbft, rear177lbft

06-02-2015, 11:38 AM	#4
JusticePete Drives: Camaro Justice Join Date: Jun 2007 Location: Virginia Posts: 20,171	Most of what you need can be found on the JPSS website. http://www.jpssonline.com/#/the-book...n-2010-camaro/ This is a direct link to the suspension and alignment section http://www.jpssonline.com/the-book-f...-2010-camaro-2