1000 HP SEVERE DUTY AXLES ???? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

markssylver · 11-15-2009, 03:19 PM

I installed a set of these axles in my car last week and today i ran the the car up to 120 mph and was getting a vibration from the rear of the car and im thinking its from the axles as i ve had the car up to 140 mph stock and dont recall the vibration also the axles i have are from the Driveline shop any one else with these axles experience this

markssylver · 11-16-2009, 06:23 PM

anybody

*CamaroSpike23* · 11-16-2009, 06:27 PM

its possible they are to blame. stock driveshaft?

markssylver · 11-16-2009, 06:32 PM

yes it does still have stock driveshaft also the vibration grows with speed

1320junkie · 11-16-2009, 06:33 PM

hmmm interesting

SMPdude · 11-16-2009, 07:43 PM

I can tell you that they have been fighting a drive line vibration on the Koni cars and they run the stock axles, but a one piece driveshaft.

markssylver · 11-18-2009, 02:15 AM

tonight on the way home from work i got on her real hard and started getting vibrations at speeds as low as 30 mph so not being able to sleep i went back towork got her up on the lift trying to figure out were the vibration could be coming from while checking the axles i noticed a lot of slop in the cv joints so i pulled the axles out and put my stockers back in put it all back together and test drove it up 154 and it was smooth as silk no vibrations so now i have to figure out what im going to do with these axles

TC · 11-18-2009, 07:19 AM

Just installed mine this weekend. Only drove it once and not at that high of speed. I did think it was a little shaky. I have not replaced my front sway bar from drag racing yet either though. Every time I do something to my car I think it takes away from how smooth it was from the factory. I will take her up a little higher today and see what happens. Unfortunately my passenger side CV joint cracked, so I will not be able to do a comparison test.

camaro1 · 11-18-2009, 08:20 AM

Quote:

Originally Posted by markssylver

so now i have to figure out what im going to do with these axles

is there no warranty on these super axles? who is the manufacture. did you even contact them?

2010 2-Tone · 11-18-2009, 08:25 AM

How much were they? There must be some type of warr on them!!

mark_p · 11-18-2009, 08:51 AM

If you have slack the axles are crap. Who made these. I am going to buy some soon and want to know who to avoid.......

speedster · 11-18-2009, 08:56 AM

From what I have been told, most of the "HD, 1000hp" axles sold are made by the same place - the Driveshaft Shop out of NC. You may want to speak with them directly.

ZZcamaro · 11-18-2009, 10:13 AM

Any updates on what the DRiveshaft shop told you?

There are a lot of folks whom want axles, but I am not going to buy ones with this problem. I already have mine lined up from another company, so that is a good thing, but I want to know where not to send my customers if they do not fix this for you!!

markssylver · 11-18-2009, 11:21 AM

the axles are from the driveline shop and they do have a 1 year warranty i just have to call them and get an authorization # to send them back and hopefully they will send a new set without the slop maybe just got a defective set

11-15-2009, 03:19 PM	#1
markssylver Drives: 95 bbb impala ss Join Date: Apr 2009 Location: md Posts: 332	1000 HP SEVERE DUTY AXLES ???? I installed a set of these axles in my car last week and today i ran the the car up to 120 mph and was getting a vibration from the rear of the car and im thinking its from the axles as i ve had the car up to 140 mph stock and dont recall the vibration also the axles i have are from the Driveline shop any one else with these axles experience this Last edited by markssylver; 11-15-2009 at 03:36 PM.

11-18-2009, 02:15 AM	#7
markssylver Drives: 95 bbb impala ss Join Date: Apr 2009 Location: md Posts: 332	problem fixed tonight on the way home from work i got on her real hard and started getting vibrations at speeds as low as 30 mph so not being able to sleep i went back towork got her up on the lift trying to figure out were the vibration could be coming from while checking the axles i noticed a lot of slop in the cv joints so i pulled the axles out and put my stockers back in put it all back together and test drove it up 154 and it was smooth as silk no vibrations so now i have to figure out what im going to do with these axles

11-18-2009, 08:56 AM	#12
speedster SST... Drives: SST Camaro 2010 Join Date: Oct 2008 Location: East Coast of Florida Posts: 5,927 View My Garage	From what I have been told, most of the "HD, 1000hp" axles sold are made by the same place - the Driveshaft Shop out of NC. You may want to speak with them directly. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1,000 HP Extreme Duty Rear Axles and CV Joints Package	SpohnPerformance	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	31	02-24-2010 11:50 PM
Gforce Engineering axles and driveshafts coming soon	GFORCE1320	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	13	02-13-2010 12:29 PM
NEW Driveshaft shop High output axles!	IPS Brandon	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	18	09-19-2009 03:38 PM
Hendrix-Engineering hd axles ready to ship	Hendrix-Engineering	V8 Bolt-Ons & Tunes	8	07-04-2009 11:12 AM
New 4.5 L Duramax Diesel V8 for light duty pickups	Scotsman	General Automotive + Other Cars Discussion	8	12-01-2008 07:21 PM

11-16-2009, 06:23 PM	#2
markssylver Drives: 95 bbb impala ss Join Date: Apr 2009 Location: md Posts: 332	anybody

11-16-2009, 06:32 PM	#4
markssylver Drives: 95 bbb impala ss Join Date: Apr 2009 Location: md Posts: 332	yes it does still have stock driveshaft also the vibration grows with speed

11-16-2009, 06:33 PM	#5
1320junkie Drives: The Imperial Army Join Date: Feb 2009 Location: The Darkside Posts: 15,742	hmmm interesting

11-16-2009, 07:43 PM	#6
SMPdude Drives: 2010 Camaros and more Join Date: Sep 2009 Location: Jacksonville, NC Posts: 115	I can tell you that they have been fighting a drive line vibration on the Koni cars and they run the stock axles, but a one piece driveshaft.

11-18-2009, 07:19 AM	#8
TC Drives: 2010 VR 2SS-RS Join Date: Dec 2008 Location: Michigan Posts: 367 View My Garage	Just installed mine this weekend. Only drove it once and not at that high of speed. I did think it was a little shaky. I have not replaced my front sway bar from drag racing yet either though. Every time I do something to my car I think it takes away from how smooth it was from the factory. I will take her up a little higher today and see what happens. Unfortunately my passenger side CV joint cracked, so I will not be able to do a comparison test.

11-18-2009, 08:25 AM	#10
2010 2-Tone Drives: 2010 RY 2SS with Custom Stripes Join Date: Mar 2009 Location: Jennings, La. Posts: 2,220 View My Garage	How much were they? There must be some type of warr on them!!

11-18-2009, 08:51 AM	#11
mark_p Drives: 2010 2SSRS m6 Join Date: Jul 2009 Location: Memphis ntn Posts: 225	If you have slack the axles are crap. Who made these. I am going to buy some soon and want to know who to avoid.......

11-18-2009, 10:13 AM	#13
ZZcamaro Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008 Location: Pittsburgh, PA Posts: 2,699	Any updates on what the DRiveshaft shop told you? There are a lot of folks whom want axles, but I am not going to buy ones with this problem. I already have mine lined up from another company, so that is a good thing, but I want to know where not to send my customers if they do not fix this for you!!

11-18-2009, 11:21 AM	#14
markssylver Drives: 95 bbb impala ss Join Date: Apr 2009 Location: md Posts: 332	the axles are from the driveline shop and they do have a 1 year warranty i just have to call them and get an authorization # to send them back and hopefully they will send a new set without the slop maybe just got a defective set