removing door panel for speaker install - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

iyam_lorne · 01-18-2010, 01:17 PM

Hi. i plan to get speakers installed in my camaro but i want to know how easy it is to get the door panels off and back on just as tight. i dont want them messinh up the doors on my brand new car.

Lightson357 · 01-19-2010, 03:31 PM

Just took mine off yesterday, it was real easy. Once you get the 5 screws, out you will need a allen wrench for the one in the door pull And it's a lil trickey to remove the plate from the door latch release. I had a real small screw driver to use to pull it off. Also with the windows rolled down, find the metal latches on the top that hold the door to the top sill and use a screw driver to release them makes it real easy to reinstall. On the driver side be careful of the trunk release button the housing is flimsy. I broke off some of the tabs so I had to black tape it together. Also there is a black rubber washer in the trunk release button. Make sure you keep up with it. That thing will bounce around on you if it falls out. But other than that it's painless. Way easier than the rear deck. Good Luck.

n-shane@hotmail.com · 01-19-2010, 03:53 PM

go on youtube they nhave a entire step by step removal of entire interior and moldings and panels. very helpful and detailed

search 2010 camaro door panel removal or somthing like that.,

skuttduck · 01-19-2010, 03:55 PM

Or go here, and look at this thread. They were so kind as to post the GM instructions.

http://www.camaro5.com/forums/showthread.php?t=59422

01-18-2010, 01:17 PM	#1
iyam_lorne Drives: '94 Grand Prix SE Join Date: Aug 2009 Location: canada Posts: 174	removing door panel for speaker install Hi. i plan to get speakers installed in my camaro but i want to know how easy it is to get the door panels off and back on just as tight. i dont want them messinh up the doors on my brand new car. __________________ ABM(changed to SIM) 1LT Automatic w/RS, polished alum, conv&conn pkg - May 1, 2010

01-19-2010, 03:53 PM	#3
n-shane@hotmail.com Drives: 2010 MAROOOOOO Join Date: Jun 2009 Location: GLENDORA, CA Posts: 350	go on youtube they nhave a entire step by step removal of entire interior and moldings and panels. very helpful and detailed search 2010 camaro door panel removal or somthing like that., __________________ THIS CAR IS AMAZING!!!!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Complete ******** install from a Novice	Susantroy1	Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum	63	07-31-2015 02:25 PM
DIY : Install underdrive pulley on 2010 Camaro SS	Nine Ball	Camaro DIY & HOW-TO instructions & discussions	34	09-30-2013 09:25 PM
Want to install Recarro Race Seats what about SRS fault from removing stock seat?	55Designs	5th Gen Camaro SS LS LT General Discussions	0	12-08-2009 04:10 PM
Removing Front bumper for Halo install?	Double O Nick	Camaro DIY & HOW-TO instructions & discussions	11	09-06-2009 09:30 AM
DIY : Install catback on 2010 Camaro SS	Nine Ball	Camaro DIY & HOW-TO instructions & discussions	3	08-09-2009 05:36 PM

01-19-2010, 03:31 PM	#2
Lightson357 Drives: 2012 45th Edition Convertible RS Join Date: Jan 2010 Location: Atlanta, GA Posts: 31	Just took mine off yesterday, it was real easy. Once you get the 5 screws, out you will need a allen wrench for the one in the door pull And it's a lil trickey to remove the plate from the door latch release. I had a real small screw driver to use to pull it off. Also with the windows rolled down, find the metal latches on the top that hold the door to the top sill and use a screw driver to release them makes it real easy to reinstall. On the driver side be careful of the trunk release button the housing is flimsy. I broke off some of the tabs so I had to black tape it together. Also there is a black rubber washer in the trunk release button. Make sure you keep up with it. That thing will bounce around on you if it falls out. But other than that it's painless. Way easier than the rear deck. Good Luck.

01-19-2010, 03:55 PM	#4
skuttduck Drives: 2010 RJT 2LT Camaro Join Date: May 2009 Location: East Lansing, MI Posts: 2,529	Or go here, and look at this thread. They were so kind as to post the GM instructions. http://www.camaro5.com/forums/showthread.php?t=59422