Do you have to run a 2.5 inch axleback with the ARH headers and x-pipe? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

g-townmach · 02-08-2010, 07:32 PM

I currently have JBA's 3 inch competition catback. I am looking to go to the 1.875 American Racing Headers and their catted 3 inch Xpipe. But heres the thing, I know how at the end of their Xpipe its necked down to accommodate 2.5 inch. So that you can run your factory mufflers or the plethora of 2.5 axle-backs available. But I want to just ditch my H-pipe from JBA and just bolt up the ARH xpipe to the remaining JBA axle-back (which is 3 inch). MAKE SENSE??

Anybody else run into this? Please advise. All else fails I shall just cut and weld.

Heres what I currently have:
http://www.latemodelrestoration.com/item/JBA-403114

And heres the ARH's and Xpipe I want:
http://www.lethalperformance.com/exh...x-pipe-p-29749

2010 4 DW · 02-08-2010, 07:45 PM

Why not just buy the JBA 1 7/8 Longtubes and Mids and replace the few inches of 2.5 at the front of your exhaust with 3". I love the way the H-pipe sounds on my car.

You will save a ton as the JBA 1 7/8 Longtubes are about $1200.00 with cats.

Just my o2

g-townmach · 02-08-2010, 08:09 PM

Quote:

Originally Posted by 2010 4 DW

Why not just buy the JBA 1 7/8 Longtubes and Mids and replace the few inches of 2.5 at the front of your exhaust with 3". I love the way the H-pipe sounds on my car.

You will save a ton as the JBA 1 7/8 Longtubes are about $1200.00 with cats.

Just my o2

Yeah I'm considering that too. But to be honest I'm just curious to see what the JBA mufflers will sound like w/ an Xpipe. Plus, I plan to do a mid-size cam soon thereafter and want to scavange as much as possible with the X.

g-townmach · 02-09-2010, 10:39 AM

Anyone else??

JANNETTYRACING · 02-09-2010, 10:48 AM

Quote:

Originally Posted by g-townmach

I currently have JBA's 3 inch competition catback. I am looking to go to the 1.875 American Racing Headers and their catted 3 inch Xpipe. But heres the thing, I know how at the end of their Xpipe its necked down to accommodate 2.5 inch. So that you can run your factory mufflers or the plethora of 2.5 axle-backs available. But I want to just ditch my H-pipe from JBA and just bolt up the ARH xpipe to the remaining JBA axle-back (which is 3 inch). MAKE SENSE??

Anybody else run into this? Please advise. All else fails I shall just cut and weld.

Heres what I currently have:
http://www.latemodelrestoration.com/item/JBA-403114

And heres the ARH's and Xpipe I want:
http://www.lethalperformance.com/exh...x-pipe-p-29749

What you should do is order the ARH with the Short Cats and just bolt it up no modifications, unless you want to get rid of the 2.5 neck down at the back of the cat, front of the JBA, and that is pretty simple to do.

We stock them, and I have a used set left over from the header test I can give you a deal on.

Ted.

g-townmach · 02-09-2010, 11:00 AM

Quote:

Originally Posted by JANNETTYRACING

What you should do is order the ARH with the Short Cats and just bolt it up no modifications, unless you want to get rid of the 2.5 neck down at the back of the cat, front of the JBA, and that is pretty simple to do.

We stock them, and I have a used set left over from the header test I can give you a deal on.

Ted.

So when ordering just the ARH headers and cats it goes to 2.5? I assumed it did so people could use their stock hpipe but wasn't sure. That may be a good option. Another one would just be to weld on some 3.0 OD to 3.0 ID ball type connectors at the end of the arh 3 inch xpipe, if I chose to go that route.

JANNETTYRACING · 02-09-2010, 11:31 AM

Quote:

Originally Posted by g-townmach

So when ordering just the ARH headers and cats it goes to 2.5? I assumed it did so people could use their stock hpipe but wasn't sure. That may be a good option. Another one would just be to weld on some 3.0 OD to 3.0 ID ball type connectors at the end of the arh 3 inch xpipe, if I chose to go that route.

That is correct, Hate to see you cut up that nice 3 inch system and toss it.

Ted.

g-townmach · 02-09-2010, 11:36 AM

Quote:

Originally Posted by JANNETTYRACING

That is correct, Hate to see you cut up that nice 3 inch system and toss it.

Ted.

Wouldn't be cutting up much of the xpipe, just the back 3 inches or so. I might just go ahead and swap out everything b/c I want to see what the arh headers and xpipe would sound like with a spintech catback (always loved spintechs). But, my current jba DOES sound good.

RocketCutlass · 02-09-2010, 11:39 AM

Call Nick and tell him what you want and he'll make it. I seriously doubt it will be an issue for them not to shrink the pipe down to 2.5 inches. Nick helped me out with my 02 Camaro I had, I ordered headers and a ORY and I had a 3 inch cat back as well. not only did he make it like i asked he included a coupler pipe for free about 2 feet long for me to cut cause we werent sure if the cat back i had would reach his ORY. Nick is a stand up guy. He didnt jack up the price either since it was a small change.

RocketCutlass · 02-09-2010, 11:43 AM

Just saw you want spintechs, I have that system on my goat and I love it. Get compliments on it all the time, some die hard GM guys say it sounds like a mustang, but almost everybody loves how mustangs sound.

I dont think it sounds like a mustang but this clip right here is extremly close to what it sounds lik in person on the GTO

RocketCutlass · 02-09-2010, 11:45 AM

Also the Camaro may sound different cause the mufflers are mounted behind the rear versus the GTO being mounted closer to the middle of the car.

g-townmach · 02-09-2010, 11:56 AM

Quote:

Originally Posted by RocketCutlass

Call Nick and tell him what you want and he'll make it. I seriously doubt it will be an issue for them not to shrink the pipe down to 2.5 inches. Nick helped me out with my 02 Camaro I had, I ordered headers and a ORY and I had a 3 inch cat back as well. not only did he make it like i asked he included a coupler pipe for free about 2 feet long for me to cut cause we werent sure if the cat back i had would reach his ORY. Nick is a stand up guy. He didnt jack up the price either since it was a small change.

Yeah I was thinking about callin them and asking about that.

g-townmach · 02-09-2010, 12:00 PM

Quote:

Originally Posted by RocketCutlass

Just saw you want spintechs, I have that system on my goat and I love it. Get compliments on it all the time, some die hard GM guys say it sounds like a mustang, but almost everybody loves how mustangs sound.

I dont think it sounds like a mustang but this clip right here is extremly close to what it sounds lik in person on the GTO

Yeah I miss the sound of my 04 mach1 and my 04 cobra. (really miss the low end torque too)

02-08-2010, 07:32 PM	#1
g-townmach I FARTED Drives: 2010 2SS/RS Join Date: Nov 2009 Location: cen-tex Posts: 870	Do you have to run a 2.5 inch axleback with the ARH headers and x-pipe? I currently have JBA's 3 inch competition catback. I am looking to go to the 1.875 American Racing Headers and their catted 3 inch Xpipe. But heres the thing, I know how at the end of their Xpipe its necked down to accommodate 2.5 inch. So that you can run your factory mufflers or the plethora of 2.5 axle-backs available. But I want to just ditch my H-pipe from JBA and just bolt up the ARH xpipe to the remaining JBA axle-back (which is 3 inch). MAKE SENSE?? Anybody else run into this? Please advise. All else fails I shall just cut and weld. Heres what I currently have: http://www.latemodelrestoration.com/item/JBA-403114 And heres the ARH's and Xpipe I want: http://www.lethalperformance.com/exh...x-pipe-p-29749 __________________

02-09-2010, 10:39 AM	#4
g-townmach I FARTED Drives: 2010 2SS/RS Join Date: Nov 2009 Location: cen-tex Posts: 870	Anyone else?? __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
V8 Camaro Performance Upgrades List	Milk 1027	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	93	08-30-2021 06:56 PM
EXHAUST	Milk 1027	Wiki	2	03-07-2010 10:20 PM
ARH 1 7/8" Headers & Cat X Pipe Used 300 miles!	Jason 98 TA	V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment	36	01-10-2010 08:43 PM
JBA releases exhausts, headers and midpipes.	Bewenched	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	17	09-16-2009 04:04 PM
ARH Headers - when will we see an axleback specific made for them?	Crowley	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	10	09-11-2009 04:21 PM

02-08-2010, 07:45 PM	#2
2010 4 DW Account Suspended Drives: White 2010 RS/SS Join Date: Dec 2009 Location: San Diego Posts: 672	Why not just buy the JBA 1 7/8 Longtubes and Mids and replace the few inches of 2.5 at the front of your exhaust with 3". I love the way the H-pipe sounds on my car. You will save a ton as the JBA 1 7/8 Longtubes are about $1200.00 with cats. Just my o2

02-09-2010, 11:39 AM	#9
RocketCutlass Property USMC Drives: 95 Caprice 9C1 Join Date: May 2009 Location: Camp Lejeune Posts: 476 View My Garage	Call Nick and tell him what you want and he'll make it. I seriously doubt it will be an issue for them not to shrink the pipe down to 2.5 inches. Nick helped me out with my 02 Camaro I had, I ordered headers and a ORY and I had a 3 inch cat back as well. not only did he make it like i asked he included a coupler pipe for free about 2 feet long for me to cut cause we werent sure if the cat back i had would reach his ORY. Nick is a stand up guy. He didnt jack up the price either since it was a small change.

02-09-2010, 11:45 AM	#11
RocketCutlass Property USMC Drives: 95 Caprice 9C1 Join Date: May 2009 Location: Camp Lejeune Posts: 476 View My Garage	Also the Camaro may sound different cause the mufflers are mounted behind the rear versus the GTO being mounted closer to the middle of the car.