12-14-2009, 11:56 AM | #1 |
Drives: 2012 Challenger SRT8 Auto Join Date: Sep 2009
Location: Central New Jersey
Posts: 839
|
One more Roto-Fab CAI Install
This is a bit of a re-post from a prior CAI thread but I finally installed my Roto-Fab on my LS3 2SS over the weekend, after breaking the car in pretty hard for the first 1000 miles I did a quick oil/filter change, changed the fluid in the rear end and then popped the hood for the CAI. The install was SUPER easy, if you can change a light bulb you can install this CAI, the packaging was very good, the instructions were very clear and simple to follow. Even putzing around and taking my time itr was less than an hour from opening the hood to closing it. I did pull the 5/20 fuses overnight just to give the car a fresh start to learn with the Roto-Fab on there. The one additional thing I may do is pick up another small piece of rubber stripping to totally close off the back right corner of the heat shield from the engine compartment, while I am not sure just how much heat can get in through there and if I am being too paranoid it gives me something to do.
I went with the Roto-Fab for the following reasons; 1. I like the looks (personal preference) 2. I like the ease of installation as posted by many on this forum. (others are easy as well) 3. Based on the testing by Ted Jannety, which I have full faith in as it is related to an apples to apples, controlled environment test, I most liked the very consistent IAT's (air temp readings) as well as the fuel trims being reasonable (as others were as well). http://www.camaro5.com/forums/showthread.php?t=48202 4. I like that the unit has a few "relief" points to allow the engine to move around and the unit to "give a little". 5. I really like the investment Roto-Fab has in getting the unit right and their investment in this community, evident by some of the praise they have gotten here in the forums as well as their immediate reaction to Ted's testing and their immediate effort to see if they still had room for improvement once they got feedback from Ted, evident in this thread; http://www.camaro5.com/forums/showthread.php?t=48992 6. The price point, there are good deals to be had, you just have to pick up a phone and reach out to shops to find them, but my guess is this holds true for most of the units. Got mine from Brandon at IPS Motorsports I was not concerned with 2-3hp difference between units, I was most concerned with a solid all around package IN MY EYES that served as a good starting point in allowing the engine to breath better on the intake side and not be a bottleneck when I upgrade the exhaust side of things with long tubes, hi-flow cats, and less restrictive exhaust later on. For me, there were quite a few I would have gone with based on performance alone but taking all the other things into consideration I went with Roto-Fab. Hope this helps anyone contemplating a CAI, just make sure you choose the one YOU want.
__________________
"When the people find they can vote themselves money, that will herald the end of the republic." - Benjamin Franklin LS3 Camshaft Swap Do-It-Yourself Instructions - 2010 LS3 gone but not forgotten!!! Last edited by robertway; 12-14-2009 at 01:11 PM. |
12-14-2009, 12:45 PM | #2 |
|
Looks awesome
|
12-14-2009, 01:07 PM | #3 |
Drives: 1SSRS RY L99 Join Date: Aug 2009
Location: Ontario
Posts: 1,329
|
Nice and clean!!!
|
12-14-2009, 01:14 PM | #4 |
Jim
Drives: 2010 Camaro 2SS/RS Orange Join Date: Sep 2009
Location: New York, Staten Island
Posts: 362
|
I just installed mine on Saturday and the sound difference from the engine is worth every penny. Also the look the under the hood is so much cleaner looking. I'll post some pics up later.
__________________
ARH 1 7/8 with Cats, Corsa Cat-back, Roto Fab CAI, and Jannetty Tune, L99
|
12-14-2009, 04:22 PM | #5 |
Drives: Aggressive Join Date: Jul 2008
Location: Southampton, PA.
Posts: 1,086
|
Just installed mine as well, Got tired of waiting for Vararam... I love this intake, butt dyno can feel a difference and it sounds like a monster at WOT.. Great intake Roto-Fab, could not be happier
__________________
Black 2SS RS LS3 Inferno Int. '17 1LE replica 20's {MODS} KOOKS LT: Borla S-Type: Roto-Fab CAI: Hurst ST.: PFADT Stage 2, Trailing arms, Tie Rods: ECS BigBlower Cam: Fast 102mm intake: Brian Tooley racing dual spring kit: TFS pushrod set: Katech C5R timing chain: Mellings high volume oil pump: ATI Balancer: Ideal performance upgraded clutch master cylinder:Tick performance upgraded slave cylinder/throwout bearing: Mantic 9000 twin disk clutch & light weight flywheel: Tuned by Doug Ring at ECS. 475RWHP/445RWTQ.Dynapack Dyno.
|
12-14-2009, 06:15 PM | #6 |
Banned
Drives: 2010 Camaro 2SSRS and a 09' Deluxe Join Date: Oct 2009
Location: Kansas City
Posts: 117
|
I just put mine in not too long ago....
Cons... I have noticed that my average mpg. has dropped...it was 16.9 city now its 15.4 city....No biggy...i could just have a heavier foot now. Also maybe Roto Fab should have included some kind of cover or something for the back stock box mount. Because Roto Fabs box only uses one box mount. And finally with the dry filter it sits almsot too close to my fluid resivoir...Another No biggy...as long as when the motor is moven it don't knock into it. It looks like they covered everything else though.... PROS... I have to agree with the OP about everything he posted. Well made unit, not to mention IMO it's the best looking in appearence. I went with the dry filter also.... As the OP has stated there are great deals to be found out there. It only took me a month to find such a deal. I purchased mine NEW for super cheap.... $265.00 shipped for unit and dry filter. Great job Roto Fab... here's another pic.... |
12-14-2009, 06:36 PM | #7 |
Drives: 2002 Camaro SS Join Date: Jul 2009
Location: Quitman, LA
Posts: 609
|
Very clean, looks good!
__________________
2015 1LE - CAI intake, TSP longtubes,
NPP, Futral Motorsports tuned, BMR 1"lowering springs, BMR trailing arms |
12-14-2009, 07:03 PM | #8 |
I FARTED
Drives: 2010 2SS/RS Join Date: Nov 2009
Location: cen-tex
Posts: 870
|
Why'd you pull the fuses? I thought on the LS3's the fix was just the battery disconnect. Thats what the sticky says doesn't it?
__________________
|
12-14-2009, 07:09 PM | #9 |
G-Man
|
Here is mine. I have had it a couple of months and I love it.
__________________
G-Man
|
12-14-2009, 07:17 PM | #10 |
Drives: 2010 2ss/rs Join Date: Sep 2009
Location: Austin
Posts: 1,016
|
when i get one it will be a rotofab
|
12-14-2009, 07:31 PM | #11 |
Black Thunder
Drives: 2010 Camaro 2SS/RS Join Date: Oct 2009
Location: NJ
Posts: 183
|
I also installed mine on Saturday and I am well pleased with it. Bought mine from Brandon @ IPS also during his black friday sale.
|
12-14-2009, 08:52 PM | #12 |
Drives: 2010 Bumble Bee SS/RS L99/A6 Join Date: Oct 2009
Location: Florida
Posts: 43
|
Install mine a week ago and have to say I love the looks and how much it cleans up the engine room(sic).
Great product and the sound is awesome. It is not load until you get on it and then it sounds like something is fixin to get stomped! My IAT averages went from 11 - 15 deg F above ambiant to between 2 - 3 above. RJ |
12-15-2009, 04:49 AM | #13 | |
Drives: 2012 Challenger SRT8 Auto Join Date: Sep 2009
Location: Central New Jersey
Posts: 839
|
Quote:
I really just want to tune the dam thing but the warranty is too valuable to me at this time
__________________
"When the people find they can vote themselves money, that will herald the end of the republic." - Benjamin Franklin LS3 Camshaft Swap Do-It-Yourself Instructions - 2010 LS3 gone but not forgotten!!! |
|
12-15-2009, 04:54 AM | #14 | |
Drives: 2012 Challenger SRT8 Auto Join Date: Sep 2009
Location: Central New Jersey
Posts: 839
|
Quote:
__________________
"When the people find they can vote themselves money, that will herald the end of the republic." - Benjamin Franklin LS3 Camshaft Swap Do-It-Yourself Instructions - 2010 LS3 gone but not forgotten!!! |
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Unofficial 1/4 Mile (V8) 2010+ Camaro Fast List | Merc | Dragstrip and Launch Techniques Discussion | 250 | 04-01-2014 10:40 AM |
Roto Fab CAI with IOM PAint | Coop | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 9 | 09-29-2009 04:25 PM |
Vector Motorsports ECM/TCM Tune & Roto Fab CAI Package | ralyrat | Vendor and Seller review / feedback / experiences | 1 | 09-15-2009 11:39 AM |
LS3 goes 11`s Bonestock! | GMRULZ | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 28 | 12-08-2008 09:10 PM |