06-05-2018, 08:53 AM | #351 |
"Old School"
Drives: 2010 2SS L99 Join Date: Apr 2015
Location: Sherrills Ford, NC
Posts: 1,294
|
|
06-05-2018, 08:54 AM | #352 |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,273
|
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
06-05-2018, 10:48 AM | #353 |
"Old School"
Drives: 2010 2SS L99 Join Date: Apr 2015
Location: Sherrills Ford, NC
Posts: 1,294
|
Ted, I just emailed you.
|
07-17-2018, 05:56 PM | #354 |
Drives: 2014 Camaro 2SS/RS 1LE Join Date: Jul 2014
Location: houston, tx
Posts: 20
|
time to upgrade my clutch
Ted,
you have tuned my car for me a couple of years ago. I have a magna SC long tube headers, high flow cats, CAI. My car is a 1LE so already had the ZL1 fuel pump. Car has been running great for 3.5 years and over 50k miles on this setup. But my stock clutch is starting to slip. I didn't think I would make it this long on the stocker. I eventually planning on doing a cam and injector upgrade to get 650+ wheel HP so I want a clutch that will hold without sacrificing drivability. This is my daily driver after all. what would you recommend? I have been looking at the centerforce DYAD but I am open to all recommendations. I even thought about going the OEM route. |
07-18-2018, 07:45 AM | #355 | |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,273
|
Quote:
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
07-18-2018, 12:52 PM | #356 |
Drives: 2014 Camaro 2SS/RS 1LE Join Date: Jul 2014
Location: houston, tx
Posts: 20
|
Can you send me quote for the clutch. Also I thought I heard something before about these hydro throw out bearings not being any good? Do you find this to be accurate and what would you recommend I replace with. I dont want to have to drop the trans again.
|
07-18-2018, 01:06 PM | #357 | |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,273
|
Quote:
Ted.
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
07-18-2018, 09:30 PM | #358 |
|
what upgrades needed Ted
Hey Ted, great thread, I have a 2010 ss, manual trans, stock drivetrain, trans and clutch., tvs2300 magnusion (first version that came out) with 3.6 pulley, BTR blower cam stage three. ZL1 fuel pump, 93 octane, ID1050 injectors, streetcar driven, long tube headers, corsa exhaust, cold air scoop, Roto fabe cai, dyno at 6lbs of boost. I want to go as far as I can with the zl1 pump for now. How far can I pulley down for more boost? I would assume I need a boost a pump and fpcm too? As far as belt slippage I would use your JRE tensioner. Any thing else I need to help with belt slippage? Ati crank pulley etc? What kind of HP at the wheels can I expect? Thanks
__________________
2012 zl1 stock 7000 miles
2010 TVS2300, BTR cam PD stage 3, ID1050 injectors, CHE bronze trunnions, 7.400" pushrods,.660" lift platinum springs, Titanium ret, Zl1 fuel pump, Kooks LT headers, High flow cats, Roto Fab CAI, Corsa exh., Mellings oil pump, HD chain, ls2 damper, all synthetic, BMR control arms, zl1 toe link, BMR cradle mounts, W/bottle relocation, air scoop deflector, Hennessy wheels, two piece rotor, morimoto fogs, DRL harness, coilovers, Heads up install, mgw shifter, slps splitter, slp spoiler, zl1 side skirts, painted strips, debadged, tinted, 2018 emblems. Edit Signature |
07-19-2018, 08:56 AM | #359 | |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,273
|
Quote:
Supertensioner and belt Overdrive cog kit JRE FPCM JMS fuel pump voltage booster. You will gain fuel supply that will support 700 RWHP. and 3-4 more PSI boost. Each LB of boost can be 25 RWHP gain. Feel free to give me a call. 203-753-7223 Ted.
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
07-20-2018, 05:01 PM | #360 | |
|
Quote:
Thanks Ted, I'm glad to here I can get that much HP out of the zl1 pump with add ons. I'm not sure I can live with the belt whine of the cog drive actually more her then me. Maybe sitting in the car its not as bad. any other alternatives for more boost no belt slippage that you have? Such as front pulley setup? Also can this cog drive setup be installed with out the supercharger being removed? and I read on your site there is fuel rail interference that needs to be addressed also with the cog drive? I'll be doing the work myself. thanks Ted
__________________
2012 zl1 stock 7000 miles
2010 TVS2300, BTR cam PD stage 3, ID1050 injectors, CHE bronze trunnions, 7.400" pushrods,.660" lift platinum springs, Titanium ret, Zl1 fuel pump, Kooks LT headers, High flow cats, Roto Fab CAI, Corsa exh., Mellings oil pump, HD chain, ls2 damper, all synthetic, BMR control arms, zl1 toe link, BMR cradle mounts, W/bottle relocation, air scoop deflector, Hennessy wheels, two piece rotor, morimoto fogs, DRL harness, coilovers, Heads up install, mgw shifter, slps splitter, slp spoiler, zl1 side skirts, painted strips, debadged, tinted, 2018 emblems. Edit Signature |
|
07-21-2018, 08:25 AM | #361 | |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,273
|
Quote:
If it is too loud it is too tight you can tune the noise with tension. Yes we have a machined fuel rail available with the overdrive cog kit that addresses the clearance issue.
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
07-23-2018, 10:51 PM | #362 |
Hey, what would be the safest FI setup? My goal is just 600 to the crank in a 2015 1LE, nothing crazy (510 to the wheels with a 15% loss). I don't believe I would have to upgrade much if anything at all with those numbers? Supercharger or turbo, doesn't bother me either way. Whatever setup would be safest, reliable, and hold decent longevity with proper care. Would I need upgraded injectors? I know the 1LE has the ZL1 pump already. I wouldn't want to run e85. I have 93 nearby, if that's important at all.
Thanks so much! |
|
07-24-2018, 07:10 AM | #363 | |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,273
|
Quote:
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
07-28-2018, 06:43 PM | #364 | |
|
Quote:
__________________
2012 zl1 stock 7000 miles
2010 TVS2300, BTR cam PD stage 3, ID1050 injectors, CHE bronze trunnions, 7.400" pushrods,.660" lift platinum springs, Titanium ret, Zl1 fuel pump, Kooks LT headers, High flow cats, Roto Fab CAI, Corsa exh., Mellings oil pump, HD chain, ls2 damper, all synthetic, BMR control arms, zl1 toe link, BMR cradle mounts, W/bottle relocation, air scoop deflector, Hennessy wheels, two piece rotor, morimoto fogs, DRL harness, coilovers, Heads up install, mgw shifter, slps splitter, slp spoiler, zl1 side skirts, painted strips, debadged, tinted, 2018 emblems. Edit Signature |
|
|
|
|
|