Sct X3 Data logging

[oachalon]

Hello everyone,

I purchased a tune from Ted, and for the life of me i cannot get the data logging to work on the sct x3. Does someone have exact step by step instructions on what i have to do to setup the data logging.

I tried following SCT's instructions and they suck.

So if someone that bought a tune from ted and did data logging, please post instructions if you can.

[JANNETTYRACING]

I got your data log and the tune looks Perfect I guess you figured it out Ehh!

Thank You

Ted.

[oachalon]

Yeppers. Sun is starting to come out, time to have fun.

Thanks again ted.

[Rikarus]

please post them for me, I wnet out hooked up a laptop and guessed at the PID's, and ran it that way and sent Ted a csv file, but when I do it the way SCT says to the unit just tells me it has no dlf files....yikes!

[JANNETTYRACING]

Originally Posted by Rikarus

please post them for me, I wnet out hooked up a laptop and guessed at the PID's, and ran it that way and sent Ted a csv file, but when I do it the way SCT says to the unit just tells me it has no dlf files....yikes!

If you want to datalog with just the handheld you have to create, save and load a Datalogging file to the hand held, I find it better to just set a laptop on the seat and use the sct as an interface and run Livelink.

[Rikarus]

Originally Posted by JANNETTYRACING

If you want to datalog with just the handheld you have to create, save and load a Datalogging file to the hand held, I find it better to just set a laptop on the seat and use the sct as an interface and run Livelink.

ok, that is what I did, I hop e i got you the right PID's

[4xchamp]

Right from their website .

Here is a walkthrough for datalogging on the device using the X3 or the SF3.
•Plug in the X3/SF3 to the vehicles OBD2 port.
•Scroll down to Data Logging, Press Select.
•Then Scroll down to Setup Monitor, Press Select.
•Config Analog Inputs? Select Yes or No, answering yes will allow you to connect a wideband or any other 0-5V component to the device analog input
•Pick Diesel or Gas, then press select.
•You are now ready to pick the pids.
oSelect them by highlighting them and then pressing select. You’ll notice that an Arrow will show next to the PID once selected.
oYou can select up to 20 Pids. NOTE: Default parameters are generated from a generic list of readable PCM parameters. It is possible that some pids shown will not be log able on your particular vehicle.
•Press Cancel to Exit from the list of Pids.
•This will bring you to a Save Data Configuration Menu.
oSelect – Save OK, Left – Back, Cancel – Exit
•Start Data Logging
oSelect – OK, Cancel – Exit
•A Message will display stating to make sure the vehicle is running, press Select to Start Recording.
•Once The Log has started, you can press LEFT/RIGHT arrows to view additional PIDS.
•Select will Stop Recording.
•Cancel will Exit the Log.

•You can Review this Log using a Computer with Livelink 4.24 or greater installed.
•Once 4.24 is installed and open…
•Then press: File/ Import Data log file from X3/livewire.
•A pop up box appears, Select Datalog0.dat from the list, then Press Ok.
•This will open and display the saved datalog.

[GSUNCSU]

Originally Posted by 4xchamp

Right from their website .

Here is a walkthrough for datalogging on the device using the X3 or the SF3.
•Plug in the X3/SF3 to the vehicles OBD2 port.
•Scroll down to Data Logging, Press Select.
•Then Scroll down to Setup Monitor, Press Select.
•Config Analog Inputs? Select Yes or No, answering yes will allow you to connect a wideband or any other 0-5V component to the device analog input
•Pick Diesel or Gas, then press select.
•You are now ready to pick the pids.
oSelect them by highlighting them and then pressing select. You’ll notice that an Arrow will show next to the PID once selected.
oYou can select up to 20 Pids. NOTE: Default parameters are generated from a generic list of readable PCM parameters. It is possible that some pids shown will not be log able on your particular vehicle.
•Press Cancel to Exit from the list of Pids.
•This will bring you to a Save Data Configuration Menu.
oSelect – Save OK, Left – Back, Cancel – Exit
•Start Data Logging
oSelect – OK, Cancel – Exit
•A Message will display stating to make sure the vehicle is running, press Select to Start Recording.
•Once The Log has started, you can press LEFT/RIGHT arrows to view additional PIDS.
•Select will Stop Recording.
•Cancel will Exit the Log.

•You can Review this Log using a Computer with Livelink 4.24 or greater installed.
•Once 4.24 is installed and open…
•Then press: File/ Import Data log file from X3/livewire.
•A pop up box appears, Select Datalog0.dat from the list, then Press Ok.
•This will open and display the saved datalog.

I have had no luck with these instructions. If someone has better instructions that include setting up the file let me know.