ABL Light Pipes - Page 13 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

The Stig · 01-14-2012, 11:22 PM

Mine are in the mail

tennyson1 · 01-15-2012, 01:30 AM

how did u order them???

sjmautoprod · 01-15-2012, 11:04 AM

Sorry guys. Once again, I am being told that we will have pricing tomorrow.

Pricing will be for...

Dash Package: Short flex and long rigid; no cutting required

Door Package: Top of panel, or, full panel; no cutting required

Customizing Package: Longer lengths of flex or rigid that can be free-cut

There are also three types of light-projecting features available:

Continuous (like the original, Tyco pipes); can be free-cut
Tuned for a specific, longer length; minimal dimming in middle; alignment is less of an issue than continuous
Expanded; 180° output; can be free-cut

tennyson1: We still have a few of the first-run, 40" rigid and flex pieces left. These are tuned.

DNAman · 01-15-2012, 10:15 PM

Will these kits have the pipes, lights and clamps to hold the pipe to the door panels? Will the panel kits have just 1 long pipe for the whole panel or will there be two. I've very interested in these.

WCoolBreeze · 01-15-2012, 11:22 PM

I like the option of the "Tuned" or "Expanded" ones, since on the lower door panel it is not the easy to get the light aimed just right. It really has to be played with to get the same intensity from start to finish.

Walt B.

sjmautoprod · 01-16-2012, 08:40 AM

Quote:

Originally Posted by DNAman

Will these kits have the pipes, lights and clamps to hold the pipe to the door panels? Will the panel kits have just 1 long pipe for the whole panel or will there be two. I've very interested in these.

Just pipes and LED's (if desired) to start. It looks like the full door-panel kit will require two pipes as the upper-rear radius is pretty small.

Quote:

Originally Posted by WCoolBreeze

I like the option of the "Tuned" or "Expanded" ones, since on the lower door panel it is not the easy to get the light aimed just right. It really has to be played with to get the same intensity from start to finish.

Walt B.

Multiple bends is where the expanded-projection version, umm... shines.

Saint Alban · 01-16-2012, 10:58 AM

I'll take the tuned dash package when everything is ready.

sjmautoprod · 01-17-2012, 09:04 PM

Well, the pricing we received was incomplete.

The pricing we do have is...

Passenger-Side Dash, Rigid: $13.75

Customizing:

39.4" [1000mm] Rigid, Free-Cut: $19.35

78.7" [2000mm] Flex, Tuned: $39.35

Note that "tuned" can be cut, but, equal amounts should come from each end.

Hopefully, the remaining pricing comes tomorrow.

tennyson1 · 01-18-2012, 03:26 AM

Do u offer and entire pre cut kit???

bee sting · 01-18-2012, 05:50 AM

Quote:

Originally Posted by tennyson1

Do u offer and entire pre cut kit???

+1

Saint Alban · 01-18-2012, 06:43 AM

I would've liked a pre cut flex tuned dash kit.

sjmautoprod · 01-18-2012, 08:32 AM

Yes, we will have complete kits. That is just the partial pricing that we have received so far.

Saint Alban · 01-18-2012, 09:02 AM

Ok, I can wait.

sjmautoprod · 01-23-2012, 08:33 AM

I will update this later today.

01-14-2012, 11:22 PM	#169
The Stig knows 2 facts about ducks Drives: ...and they're both wrong Join Date: Aug 2009 Location: The HMS Invincible Posts: 25,072 View My Garage	Mine are in the mail __________________

01-15-2012, 11:04 AM	#171
sjmautoprod Drives: '16 2SS Join Date: Apr 2011 Location: Chicago Suburbs Posts: 2,271	Sorry guys. Once again, I am being told that we will have pricing tomorrow. Pricing will be for... Dash Package: Short flex and long rigid; no cutting required Door Package: Top of panel, or, full panel; no cutting required Customizing Package: Longer lengths of flex or rigid that can be free-cut There are also three types of light-projecting features available: Continuous (like the original, Tyco pipes); can be free-cut Tuned for a specific, longer length; minimal dimming in middle; alignment is less of an issue than continuous Expanded; 180° output; can be free-cut tennyson1: We still have a few of the first-run, 40" rigid and flex pieces left. These are tuned. Last edited by sjmautoprod; 01-15-2012 at 11:57 AM. Reason: Clarified and added diagram

01-15-2012, 11:22 PM	#173
WCoolBreeze 2SS Drives: 2016 2SS, Red Garnet Tint Join Date: Nov 2008 Location: Imperial, CA Posts: 1,343	I like the option of the "Tuned" or "Expanded" ones, since on the lower door panel it is not the easy to get the light aimed just right. It really has to be played with to get the same intensity from start to finish. Walt B. __________________ 2016 Camaro 2SS 2005 Dodge Magnum R/T (Yes it has a Hemi) 1987 Camaro RS (California Special) - For Sale Gen6, 2016 Camaro 2SS, Red Garnet Tint (with Silver Rally Stripes) Ordered: 2-12-2016 TPW: 3-7-2016 Built: 3-7-2016 VIN 1G1FH78G0157626 Delivered: 4-26-2016

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Who is up for an install day for the dash ABL? (Updated)	2010SSRSM6	USA - California	565	07-10-2012 09:41 PM
Jba catted mud pipes....check engine light on?	Camarowguy	Camaro V6 LLT Engine, Exhaust, and Bolt-Ons	13	07-23-2011 09:35 AM
WTB: ABL Light Pipe 2058296-1 Tyco	irocnroll	Interior Parts & Accessories	13	05-20-2011 09:20 PM
Those with LT's, RESET your check engine light!	TAG UR IT	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	107	08-18-2010 02:51 AM
ABL lighting and Footwell Light Install?	JProberts	USA - Mid-Atlantic	3	02-25-2010 11:17 PM

01-15-2012, 01:30 AM	#170
tennyson1 Tennyson1 Drives: Camaro Join Date: Oct 2010 Location: Florida Posts: 89	how did u order them???

01-15-2012, 10:15 PM	#172
DNAman Drives: 2011 Inferno Orange 2SS Join Date: Dec 2011 Location: Hammond, LA Posts: 10	Will these kits have the pipes, lights and clamps to hold the pipe to the door panels? Will the panel kits have just 1 long pipe for the whole panel or will there be two. I've very interested in these.

01-16-2012, 10:58 AM	#175
Saint Alban Drives: '14 Black 2SS RS Join Date: Jul 2011 Location: Queens, New York (NY5thGen.com) Posts: 978 View My Garage	I'll take the tuned dash package when everything is ready.

01-17-2012, 09:04 PM	#176
sjmautoprod Drives: '16 2SS Join Date: Apr 2011 Location: Chicago Suburbs Posts: 2,271	Well, the pricing we received was incomplete. The pricing we do have is... Passenger-Side Dash, Rigid: $13.75 Customizing: 39.4" [1000mm] Rigid, Free-Cut: $19.35 78.7" [2000mm] Flex, Tuned: $39.35 Note that "tuned" can be cut, but, equal amounts should come from each end. Hopefully, the remaining pricing comes tomorrow.

01-18-2012, 03:26 AM	#177
tennyson1 Tennyson1 Drives: Camaro Join Date: Oct 2010 Location: Florida Posts: 89	Do u offer and entire pre cut kit???

01-18-2012, 06:43 AM	#179
Saint Alban Drives: '14 Black 2SS RS Join Date: Jul 2011 Location: Queens, New York (NY5thGen.com) Posts: 978 View My Garage	I would've liked a pre cut flex tuned dash kit.

01-18-2012, 08:32 AM	#180
sjmautoprod Drives: '16 2SS Join Date: Apr 2011 Location: Chicago Suburbs Posts: 2,271	Yes, we will have complete kits. That is just the partial pricing that we have received so far.

01-18-2012, 09:02 AM	#181
Saint Alban Drives: '14 Black 2SS RS Join Date: Jul 2011 Location: Queens, New York (NY5thGen.com) Posts: 978 View My Garage	Ok, I can wait.

01-23-2012, 08:33 AM	#182
sjmautoprod Drives: '16 2SS Join Date: Apr 2011 Location: Chicago Suburbs Posts: 2,271	I will update this later today.