06-01-2009, 04:52 PM | #15 |
Petro-sexual
|
I haven't installed LTs on a 5th Gen but have installed about six sets total on 4th Gens.
I'd say to start with removing the negative battery cable Jack the car up and get it safely on jack stands as high as you can Pull the plug wires and plugs Pull the dipstick Pull the steering shaft Loosen the intermediate pipes, post cats' Remove the cat' pipes Remove the manifolds from under the car Clean the gasket flanges Slide the LTs into position and bolt them in Add the cats' and/or mid-pipes and align to the headers Put everything else back together Test for leaks and get a tune Obviously a little abbreviated but I think one should get the point
__________________
'20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // RFBG // Soler 103 // TooHighPSI Port Injection // THPSI Billet Lid // FF // Katech Drop-In // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs |
06-01-2009, 07:59 PM | #16 |
NEcamaro5
|
3rd gen shorty headers go through the top. do it all the time. you do have to take youre time if you heat rap them first.
|
06-08-2009, 05:11 PM | #17 |
The Demon Photographer
|
If you want to make the trip to VA, I will install them for you for $300. While you wait. You can even watch if you want.
__________________
1SS IOM LS3, GM 4-pack guages, SLP SS Front Emblem, Roto-Fab CAI, Solo Performance Mach X Exhaust, Barton Industries Short Throw Shifter |
06-10-2009, 08:07 PM | #18 |
I put the FU back in FUN
Drives: 1969 SS 396 , 2010 Camaro SS Join Date: Jun 2009
Location: Between Weatherford and Azle TX hway730
Posts: 2,129
|
$300 is cheap if you are close and going to pay someone to do it anyways .
|
07-03-2009, 11:51 AM | #19 |
www.Camaro5store.com
|
Dude...there is so much room under the engine bay, it's crazy. I should take some pix of my headers on my LS3 just to show you how roomy it is under there.
|
07-03-2009, 02:41 PM | #20 |
Petro-sexual
|
DO IT!!! I'd love to see what's goin' on in there
__________________
'20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // RFBG // Soler 103 // TooHighPSI Port Injection // THPSI Billet Lid // FF // Katech Drop-In // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs |
07-03-2009, 06:59 PM | #21 |
Drives: 2010 IBM SS/RS Join Date: Oct 2008
Location: Edmonton, Alberta
Posts: 805
|
I 2nd this.
__________________
**sold** 2010 2SS/RS, 6spd manual, imperial blue metallic w/black leather
Blacked out tail/signal lights, 5% rear tint, 20% sides, Dynomax Bullet mufflers, Barton short throw shifter, Clear Image offroad downpipes |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
V8 Camaro Performance Upgrades List | Milk 1027 | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 93 | 08-30-2021 05:56 PM |
Headers for the V6? | Xanthos | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 49 | 08-04-2011 12:51 PM |
EXHAUST | Milk 1027 | Wiki | 2 | 03-07-2010 09:20 PM |
Shorty headers | 1fine79 | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 1 | 05-13-2009 09:19 AM |
Headers Question | SIK07GTSTANG | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 9 | 04-23-2009 07:14 PM |